599912

Makita EY401MP Handleiding

6
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
6
Part description (Fig. 1)
The numbers below refer to the gure
1. Shaft
2. Gear Case
3. Oil cap
4. Oil tank
5. Bar holder
6. Guide bar
7. Saw chain
8. Guide bar cover
Safety precautions
WARNING: Read all safety warnings and all instructions
in this booklet and the instruction manual of the power unit.
Failure to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term “pole saw” and “equipment” in the warnings and
precautions refer to the combination of the attachment and the
power unit.
The term “motor” in the warnings and precautions refers to the
engine or electric motor of the power unit.
Intended use
This attachment is designed for only the purpose of pruning •
branches and limbs less than 15 cm in diameter in conjunction
with an approved power unit. Never use the attachment for the
other purpose. Abusing the attachment may cause serious injury.
General precautions
Before starting the pole saw, read this booklet and the instruction •
manual of the power unit to become familiar with the handling of
the pole saw.
Do not lend the attachment to a person with insufcient •
experience or knowledge regarding handling of pole saws.
When lending the attachment, always attach this instruction •
manual.
Do not allow children or young persons under 18 years old to use •
the pole saw. Keep them away from the pole saw.
Handle the pole saw with the utmost care and attention.•
Never use the pole saw after consuming alcohol or drugs, or if •
feeling tired or ill.
Never attempt to modify the attachment.•
National regulations may restrict of the use of the equipment.•
Follow the regulations about handling of pole saws and chain
saws in your country.
Personal protective equipment
Wear safety helmet, protective goggles and protective gloves to •
protect yourself from ying debris or falling objects. (Fig. 2)
Wear ear protection such as ear muffs to prevent hearing loss.•
Wear proper clothing and shoes for safe operation, such as •
a work overall and sturdy, non-slip shoes. Do not wear loose
clothing or jewelry. Loose clothes, jewelry or long hair can be
caught in moving parts.
When handling the saw chain or adjusting the chain tension, wear •
protective gloves. Saw chain can cut bare hands severely.
Work area safety
• Danger: Keep the pole saw at least 15 m away from electric
lines and communication cables (including any branches
contacting them). Touching or approaching high-voltage lines with
the pole saw can result in death or serious injury. Watch power
lines and electrical fences around the work area before starting
operation.
Operate the pole saw under good visibility and daylight conditions •
only. Do not operate the pole saw in darkness or fog.
Start and operate the engine only outdoors in a well ventilated •
area. Operation in a conned or poorly ventilated area can result
in death due to suffocation or carbon monoxide poisoning.
During operation, never stand on an unstable or slippery surface •
or a steep slope. During the cold season, beware of ice and snow
and always ensure secure footing.
During operation, keep bystanders or animals at least 15 m •
away from the pole saw. Stop the motor as soon as someone
approaches.
Before operation, examine the work area for wire fences, walls, •
or other solid objects. They can damage the saw chain.
• WARNING: Use of this product can create dust containing
chemicals which may cause respiratory or other illnesses.
Some examples of these chemicals are compounds found in
pesticides, insecticides, fertilizers and herbicides.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially
designed to lter out microscopic particles.
Putting into operation
Before assembling or adjusting the equipment, switch off the •
motor and remove the spark plug cap or the battery cartridge.
Before handling the saw chain or adjusting the chain tension, •
wear protective gloves.
Before starting the motor, inspect the equipment for damages, •
loose screws/nuts or improper assembly. Sharpen blunt saw
chain. If the saw chain is bent or damaged, replace it. Check all
control levers and switches for easy action. Clean and dry the
handles.
Never attempt to start the motor if the equipment is damaged or •
not fully assembled. Otherwise serious injury may result.
Adjust the shoulder harness and hand grip to suit the operator’s •
body size.
Adjust the chain tension properly. Rell the chain oil, if necessary.•
Starting motor
Wear the personal protective equipments before starting the motor.•
Start the engine at least 3 meters (10 feet) away from the fueling •
spot.
Before starting the motor, make sure that there is no person or •
animal in the work area.
When starting the engine or inserting a battery cartridge, keep •
the saw chain and guide bar clear of your body and other object,
including the ground. The saw chain may move when starting
and may cause serious injury or damage to the saw chain and/or
property.
Place the equipment on rm ground. Maintain good balance and •
secure footing.
When pulling the starter knob, hold the power unit rmly against •
the ground by your left hand. Never step on the drive shaft of the
power unit. (Fig. 3)
Follow the instruction manual of the power unit for starting the •
motor.
Check that there is sufcient difference between idling and •
engagement speed to ensure that the attachment is at a standstill
while the engine is idling (if necessary reduce idling speed).
If the saw chain moves at idle, stop the engine and adjust the idle •
speed down.
Operation
In the event of an emergency, switch off the motor immediately.•
If you feel any unusual condition (e.g. noise, vibration) during •
operation, switch off the motor. Do not use the equipment until
the cause is recognized and solved.
The saw chain continues to move for a short period after •
releasing the throttle trigger or switch off the motor. Don’t rush to
contact the saw chain.
With the engine running only at idle, attach the shoulder harness.•
During operation, use the shoulder harness. Keep the equipment •
on your right side rmly. (Fig. 4)
Hold the front handle with the left hand and the rear grip with the •
right hand, no matter you are right-hander or left-hander. Wrap
your ngers and thumbs around the handles.
Never attempt to operate the equipment with one hand. Loss of •
control may result in serious or fatal injury. To reduce the risk of
injury, keep your hands and feet away from the blades.
Do not overreach. Keep proper footing and balance at all times. •
Watch for hidden obstacles such as tree stumps, roots and
ditches to avoid stumbling. Clear fallen branches and other
objects away.
Never work on a ladder or tree to avoid loss of control.•
… 6 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita EY401MP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita EY401MP in de taal/talen: Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 2,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info