599871
9
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
9
Oil Alert System (Fig. 14)
The engine can be damaged if there is an insufficient
amount of oil in the crankcase. The Oil Alert system
prevents this from happening by automatically stopping
the engine before the oil level in the crankcase falls below
the safe limit (the engine switch will remain in the “I (ON)”
position). When the oil alert system works, the oil level
warning lamp lights up in red. The oil level should always
be checked before each use, regardless of this Oil Alert
system.
If the engine stops and fails to restart, check the engine oil
level before troubleshooting in other areas.
NOTICE:
When the amount of oil in the crankcase is sufficient, the
pilot lamp lights up in green. When the amount of oil is
insufficient, the oil level warning lamp lights up in red. Be
sure to add oil before using the generator.
AC Circuit Breaker (Fig. 10)
The AC circuit breaker automatically turns off if there is a
short circuit or a significant overload of the generator at
the receptacle. If the AC circuit breaker is turns off
automatically, make sure that the appliance is working
correctly and does not exceed the rated load capacity of
the circuit before turning on the AC circuit breaker again.
The AC circuit breaker may be used to turn the generator
power on or off.
AC Circuit Protector (EG4550A, EG5550A,
EG6050A only) (Fig. 11)
The AC circuit protectors automatically turn off if there is a
short circuit or a significant overload of the generator at
the 26A 230V. If an AC circuit protector turns off
automatically, make sure that the appliance is working
correctly and does not exceed the rated load capacity of
the circuit before resetting the AC circuit protector on.
GENERATOR USE
Connections to a Building’s Electrical
System
A qualified electrician must make the connections for
standby power to a building’s electrical system. Make sure
that the connection isolates the generator power from the
utility power, and complies with all applicable laws and
electrical codes. A transfer switch, which isolates
generator power from utility power, can be purchased
through authorized Makita generator dealers.
WARNING:
Electrical current from the generator may backfeed
into the utility lines if connections to a building’s
electrical system are made improperly. Such backfeed
may electrocute utility company workers or others
who come into contact with the lines during a power
outage, and the generator may explode, burn, or
cause fires when the utility power is restored. Consult
the utility company or a qualified electrician.
Ground System
Makita portable generators are equipped with a system
ground that connects generator frame components to the
ground terminals in the AC output receptacles. Since the
system ground is not connected to the AC neutral wire, if
the generator is tested by a receptacle tester, it will show
the same ground circuit condition as for a home
receptacle.
AC Applications
Before connecting an appliance or power cord to the
generator:
Make sure that it is in good working condition. Faulty
appliances or power cords can cause electrical shock.
If an appliance begins to operate in an abnormal
manner, becomes slow, or stops suddenly, turn it off
immediately. Disconnect the appliance, and determine
whether there is a problem with the appliance or if the
rated load capacity of the generator has been
exceeded.
Make sure that the electrical rating of the tool or
appliance does not exceed the generator’s rating.
Never exceed the maximum power rating of the
generator. Power levels between rated and maximum
may be used for no more than one hour.
NOTICE:
Substantial overloading will turn off the circuit breaker.
Exceeding the time limit for maximum power operation or
slightly overloading the generator may not turn off the
circuit breaker or circuit protector, but will shorten the
service life of the generator.
Limit operation requiring maximum power to one hour.
Maximum power is as follows:
EG2250A: 2.2 kW
EG2850A: 2.8 kW
EG4550A: 4.5 kW
EG5550A: 5.5 kW
EG6050A: 6.0 kW
For continuous operation, do not exceed the rated power.
Rated power is as follows:
EG2250A: 2.0 kW
EG2850A: 2.6 kW
EG4550A: 4.0 kW
EG5550A: 5.0 kW
EG6050A: 5.5 kW
The total power requirements (VA) of all appliances
connected to the generator must be considered. Rating
information for appliances and power tools are usually
listed near the model number or serial number.
AC Operation (Fig. 12)
1. Start the engine.
2. Turn on the AC circuit breaker.
3. Plug in the appliance.
NOTICE:
Before connecting any appliance to the generator, make
sure they are in good working condition. If an appliance
begins to operate in an abnormal manner, becomes slow,
or stops suddenly, turn off the ignition switch lever
immediately. Then disconnect the appliance and check for
signs of malfunction.
Most motorized appliances require more than their rated
power for startup.
Do not exceed the current limit specified for any one
receptacle. If an overloaded circuit causes the AC circuit
breaker or AC circuit protector to turn off, reduce the
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita EG4550A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita EG4550A in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info