574943
8
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
8
Technical data ECU 45
Supply voltage (input) 230 - 240 V ~
Line frequency 50/60 Hz
Charging voltage (output) 7.2 – 14.4 V (DC)
Charging current
Quick charge max. 3 A
Compensation charge pulsating app. 0.06 A
Charging time for
NiCd 1.4 Ah app. 38 min
NiCd 1.7 Ah app. 42 min
NiCd 2.0 Ah app. 46 min
NiMH 3.0 Ah app. 70 min
Weight 0.5 kg
The illustrations mentioned can be found
on a fold-out page at the beginning of the
operating instructions.
1 Directions for use
The charger ECU 45 has been designed to
charge the battery packs speci ed under
Chapter 2.
The user will be liable for damage due to
improper use.
For your own safety
Repairs may only be carried out by quali-
ed experts. Warning: ECU 45 charging
device: Even after disconnection from the
mains, there is still a high capacitor volt-
age on the power output component on
the inside of the device.
Protect equipment against moisture.
Do not use the charger if the connecting
cable is damaged, unplug immediately
from the main.
Protect the cable against heat, oil and
sharp edges.
Never carry the tool by its cable and never
use to the cable to pull the plug out of the
wall socket.
Do not use defect and damaged battery
packs.
Only use original Festool battery packs.
Do not use spent and recycled battery
packs. The user shall be liable for dam-
ages if Festool original battery packs are
not used.
Do not place spent battery packs into
re or into domestic waste. Attention:
Festool offers an ecological friendly waste
disposal for used battery packs (refer to
RECYCLING OF BATTERY PACKS).
Do not open battery packs.
Do not store battery packs with metal
objects (danger of short circuit).
No metal objects (metal chips) should
enter the charger at the contact points as
well as through the cooling slits into the
equipment (danger of short circuit).
Keep out of reach of children.
Check the tool for damages before use.
Have damaged parts repaired or replaced
by the customer service department.
2 Charge battery pack
All NiCd and NiMH battery packs between 7.2
V and 14.4 V voltage can be charged with the
ECU 45 charger.
The battery type used (NiCd or NiMH) is
detected automatically. Charging is control-
led by a microprocessor.
Warning: If a warm NiMH battery pack
(>37°C) is inserted, charging will only be
carried out at a lower charge current.
In this case the charging time for a battery
pack with 3.0 Ah is around 100 min..
By the in uence of powerful electromag-
netic perturbations while charging it can be
switched over to conservation charge.
Thereby the charger can not take in a dan-
gerous or unsafe status
The LED (1.10) shows the charge status of
the charger.
LED yellow - steady
= Charger is ready for use.
LED green - ashing
= Battery pack being charged.
LED green - steady
= Battery pack fully charged, conservation
charge on.
LED red - ashing
= General malfunction, e. g. full contact
not being made, short-circuit, battery pack
faulty.
LED red - steady
= Temperature of battery pack is outside
permissible limit (5° - 45°C).
Charging
Connect charger to mains.
Warning: The line voltage and frequency
must correspond with the data on the rat-
ings plate!
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita ECU 45 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita ECU 45 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info