448381
12
Verklein
Vergroot
Pagina terug
1/149
Pagina verder
12
MOUNTING OF HANDLE
Fix a barrier to the left side of the machine together with the
handle for operators protection.
Do not adjust position of the loop handle too close to the control
grip. Keep not less than 25cm distance between the handle
and the grip.
(a distance collar is provided for this purpose.)
MOUNTING OF PROTECTOR
To meet the applicable safety provisions, only the tool/protector
combinations as indicated in the table must be used. Failure to do
so may result in serious injury or death to user or bystanders.
Be sure to use genuine MAKITA cutter blade or nylon
cutting head.
The cutter blade must be well clean, sharp and free of cracks
or breakage.
If the cutter blade contacts any hard objects or stones during
operation, stop the engine and check the blade immediately.
Clean and sharpen or replace the cutter blade at least every
three hours of operation.
The outside diameter of the cutter blade must not exceed 255
mm (10-1/32). Never use any blades surpassing 255 mm (10-
1/32) in outside diameter.
CAUTION : The appropriate guard must always be in-
stalled, for your own safety and in order to
comply with accident-prevention regulations.
Operation of the equipment without the
protector being properly in place must never
be attempted.
Fix protector to a gear case by 4 bolts firmly
Never use a blush cutter without a protector or with a broken
protector.
MOUNTING OF CUTTER BLADE OR
NYLON CUTTING HEAD
Turn the machine upside down, and you can replace the cutter
blade or nylon cutting head easily.
Mounting of cutter blade
Fit a cutting blade and other parts in the order as in the illustra-
tion. Thrust a bar or allen wrench into a hole of the gear case
until the cutting blade is locked and will not turn. Tighten a nut
by turning to counter-clockwise with a combination wrench.
(Note that the nut is tightened or loosened in the opposit
direction of a usual nut.)
The nut must be re-tightened every time before use.
For this brush cutter, we recommend the cutting attachments on
the right.
Never attempt to cut a tree, a log, wood or other hard materials.
[Tightening torque: 28 48 N
m]
NOTE : Always wear gloves when handling the cutter
blade.
Mounting of nylon cutting head
The blade cap, bolt cover and nut are not necessary for
mounting the nylon cutting head. The nylon cutting head should
go on top of the grass cover.
Insert the allen wrench through the hole in the gear case and
rotate the blade holder until it is locked with the alln wrench.
Then screw the nylon cutting head onto the shaft by turning it
counter-clockwise.
Remove the allen wrench.
Star Blade
Protector for metal
blades
Eddy Blade
PART NO.
6418501400
PART NO.
6418501900
PART NO.
6118502000
Nut
Bolt cover
Blade cap
Blade
Grass cover
Blade holder
Protector plate
Protector
Gear case
PART NO.6348003000 PART NO.174345800
Nylon cutting head
to engine
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita EBH341R bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita EBH341R in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 3,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info