Handleiding Makita DUR141 (pagina 12 van 22) (Nederlands, Engels)

599972

Verklein

Vergroot

Pagina terug

1/22

Pagina verder

Cutting the grass near a tree, concrete

block, brick or garden stone (Fig. 27)

Hold the trimmer tilting at a level so that it does not

contact the ground surface and cut the grass using the

nylon cord tip like knocking the ground. In this work,

smooth feeding out is needed because the nylon cord

wears more quickly than usual.

NOTE:

• Getting the trimmer too close to a tree, concrete block,

brick or garden stone or the like during performing the

edging work or such similar cutting work may cause the

nylon cord to be cut off halfway inside the spool cover.

At this time, take the spool out of the spool cover and

then set the nylon cord again properly by referring to

the section titled “Installing or removing the nylon

cutting head” and “Winding a new nylon cord on the

spool”. Using the tip of the nylon cord during operation

brings the best result of operation and therefore it is

recommended to keep the tool more than 5 cm away

from the tree, concrete block, brick or garden stone or

the like.

Start the trimmer before getting close to the grass to be

cut.

Cut the grass using the nylon cord tip by moving the

trimmer from right to left and proceed slowly, keeping the

trimmer tilted at the angle of about 30° in relation to the

ground surface.

When cutting high grass, cut in layers always beginning

from the top with each cut length short.

Using the tool as an edger

Using the tool as an edger allows the operator to cut along

the edge of the concrete block, brick and the like. (Fig. 28)

For using the tool as an edger, hold the shaft of the

trimmer with one hand and turn the grip counter clockwise

to loosen the shaft. Rotate the shaft with the motor

housing 180° and tighten the grip clockwise until it locks.

(Fig. 29)

NOTE:

• Before rotating the shaft, it needs to be fully shortened

or extended.

• After changing to the edger position, make sure that

the motor housing and shaft are locked.

To obtain a good result of finish cutting, move parallel to

the edge you are going to perform an edging work.

(Fig. 30)

Cutting the grass in a tight place or on a

slope

WARNING:

• When cutting the grass on a slope, be careful of

stones, grass and other foreign objects thrown from the

cutting head area.

• When cutting the grass on a slope, make sure that you

always keep a good and stable footing.

To ease the work in a tight place which restricts the

height, such as cutting the grass under an outdoor wood

deck and similars, push the lock button and then bend

down the cutting head so that the shaft is parallel to the

ground surface. Adjusting the cutting head angle properly

in this way helps you cut the grass on a slope. (Fig. 31)

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before attempting to

perform inspection or maintenance on the tool.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

NOTICE:

Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Nylon cutting head

• Nylon cords

• Shoulder strap

• Goggles

• Various type of Makita genuine batteries and chargers

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN786:

Model DUR141

Sound pressure level (L

): 75 dB (A)

Sound power level (L

): 83.7 dB (A)

Uncertainty (K): 2.5 dB (A)

Model DUR181

Sound pressure level (L

): 82 dB (A)

Sound power level (L

): 88.5 dB (A)

Uncertainty (K): 2.5 dB (A)

Wear ear protection.

Vibration

ENG904-2

The vibration total value determined according to EN786:

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita DUR141 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Makita DUR141

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info