600212
7
Verklein
Vergroot
Pagina terug
1/72
Pagina verder
7
NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Switch action (Fig. 3)
CAUTION:
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the “OFF” position when
released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
NOTE:
The tool automatically stops if you keep pulling the
switch trigger for about 360 seconds.
Lighting up the front lamp (Fig. 4 & 5)
CAUTION:
Do not look in the light or see the source of light
directly.
To turn on the lamp status, press the button for few
seconds. To turn off the lamp status, press the button
for few seconds again.
With the lamp status ON, pull the switch trigger to turn on
the lamp. To turn off, release it. The lamp goes out
approximately 10 seconds after releasing the switch
trigger.
With the lamp status OFF, the lamp will not turn on even
if the trigger is pulled.
NOTE:
To confirm the lamp status, pull the trigger. When the
lamp lights up by pulling the switch trigger, the lamp
status is ON. When the lamp does not come on, the
lamp status is OFF.
While pulling the switch trigger, the lamp status cannot
be changed.
For approximately 10 seconds after releasing the
switch trigger, the lamp status can be changed.
Reversing switch action (Fig. 6)
CAUTION:
Always check the direction of rotation before operation.
Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
Characteristics of Cordless Oil-impulse Driver
The Makita Cordless Oil-impulse Driver is a hydraulically
operated impact tool using oil viscosity to produce
impacts. Since oil viscosity changes with the
temperature, be aware of the following two points when
operating the tool.
1. Avoid using the tool below –10°C (14°F) of
temperature. When the tool temperature goes down
below the degrees, this may cause damage to the
motor of tool due to poor impulse.
2. When the tool becomes too hot, it may take longer to
set screws.
3. The tool can overheat, causing a failure or hand
burn if you operate it continuously for long hours. Let
the tool cool off for more than 30 minutes before
changing batteries during a long, continuous job.
Changing the impact force (Fig. 7)
015147
Impact force grade
displayed on panel
Maximum blows
Application Work
DTS131 DTS141
Hard
2,500
(min
–1
)
2,700
(min
–1
)
Tightening when force and
speed are desired.
Tightening in underwork
material / Tightening long
screws.
Medium
2,200
(min
–1
)
2,200
(min
–1
)
Tightening when a good
finishing is needed.
Tightening in the finishing
board, plaster board.
Soft
1,400
(min
–1
)
1,400
(min
–1
)
Tightening when excessive
tightening need to be avoided
because of potentially
clogged female screw and
broken or damaged screw
head.
Tightening sash screw/
Tightening small screws such
as M6.
Tightening bolt up to M8.
T mode
1,400
(min
–1
)
1,400
(min
–1
)
Tightening when speed and
good finishing are needed.
Tightening when speed and
good finishing are needed.
Tightening bolt up to M8.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DTS141 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DTS141 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 3,95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info