691889
11
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
11 ENGLISH
CAUTION: Hold the tool rmly so that it does
not shake when cutting. Cutting with the tool
shaking will shorten the life of the Tipped Saw and
damage the blades.
CAUTION: Position the tool so it is at 90
degrees to rebar to be cut. If the tool is not at 90
degrees to the rebar, it can cause shaking and
overload the tool.
CAUTION: Do not start cutting immediately
after the motor is switched on. Allow the Tipped
Saw to reach full speed before beginning to cut.
CAUTION: Do not remove the battery when
the motor is switched on. Doing so can cause
damage to the motor’s electronics.
6. After nishing the cut, push down on the rear end
of the Switch which will cause the Switch to move to the
“O” position and turn off the motor.
CAUTION: This tool is designed to cut rebar.
Please contact the manufacturer or your local
dealer if you want to cut other materials. Cutting
other materials will damage the Tipped Saw
blades.
Caution when cutting
1. Ensure that the Tipped Saw blade is well away
from the material to be cut before switching on.
2. Slow down the forward (cutting) movement of the
tool when approaching the end of the cut. This is espe-
cially important when the piece to be cut is less than 50
mm in length. The piece cut off can strike the Tipped
Saw blades, damaging them and cause serious injury.
3. When the Tipped Saw blades become blunt or
chipped. replace the blade. Continuing to use it in this
condition will overload the tool.
4. If the material moves or shakes, when being cut,
stop the operation and properly secure the material.
5. Do not hold by hand the material to be cut. Doing
so may result in personal injury.
6. Do not cut rebar that in size or hardness exceeds
the cutting capacity of the tool.
Replace the Tipped Saw when any
of the below occurs
1. Warning Lamp (red) blinks frequently even though
the battery is fully charged.
2. The Tipped Saw blades are chipped or worn.
3. The cutting speed is very slow.
4. The surface of the cut piece is discolored by heat.
NOTE: Tipped Saw blades cannot be resharpened.
How to t the Dust Bag
Fig.7: 1. Dust Bag
1. Place the open end of the Dust Bag over the Dust
Bag Holder and secure in place with the draw strings.
2. Give the bag a sharp tug to ensure it is properly
secured.
CAUTION: The Dust Bag is made from non-
ammable material but very hot debris, such as
that produced when cutting with a worn Tipped
Saw blade, can melt the material. Be aware of this
possibility when using the Dust Bag.
Battery Indicator function
Fig.8: 1. Battery Indicator
When you turn the tool on, the battery indicator shows
the remaining battery capacity. (see table 1)
Table 1
Battery indicator status
Remaining battery
capacity
:On :Off :Blinking
5 0 %-1 0 0 %
2 0 %-5 0 %
0 %-2 0 %
Charge the battery
Automatic speed change function
Fig.9: 1. Mode Indicator
The tool has ‘high speed mode’ and ‘high torque mode’.
It will select the operating mode automatically, accord-
ing to the work load. When the mode indicator lights up
during operation, the tool is in high torque mode. (see
table 2)
Table 2
Mode indicator status Operation mode
High speed mode
High torque mode
Tool / battery protection function
The tool will automatically stop during operation if the
tool or battery is placed under one of the following
conditions:
- The tool is overloaded
- The tool overheats
If the tool is repeatedly operated under these condi-
tions, the protection system will lock the tool.
Overload protection
If the tool is overloaded during cutting, it will automati-
cally stop. In this situation, turn the tool off and remove
the cause of the overload then restart the tool.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DSC250 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DSC250 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 7,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info