Handleiding Makita DPJ140 (pagina 8 van 16) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens)

691239

Verklein

Vergroot

Pagina terug

1/16

Pagina verder

– If the tool continues to be overloaded and the indica-

tion lamp continues to light up for approximately two

seconds, the tool stops. This prevents the motor and

its related parts from being damaged.

– In this case, to start the tool again, move the slide

switch to the “O (OFF)” position once and then to the

“I (ON)” position.

– Battery cartridge replacing signal

– When the remaining battery capacity gets small, the

indicator lamp lights up during operation earlier than

enough capacity battery use.

– Accidental re-start preventive function

– Even if the battery cartridge is inserted on the tool

with the slide switch in the “I (ON)” position, the tool

does not start. At this time, the lamp flickers slowly

and this shows that the accidental re-start preven-

tive function is at work.

– To start the tool, first slide the slide switch toward the

“O (OFF)” position and then slide it toward the “I

(ON)” position.

Adjusting the depth of groove (Fig. 4)

6 grooving depths can be preset according to the size of

biscuit to be used.

Refer to the table below for the correspondence between

the sizes marked on the stopper and the biscuit size.

Fine adjustments to the grooving depth can be made by

turning the adjusting screw after loosening the hex nut.

This may become necessary after the blade has been

resharpened a few times.

* With the rubber spikes removed.

012681

Angle guide (Fig. 5 & 6)

The angle guide height can be moved up and down to

adjust the position of the blade in relation to the top of the

workpiece.

To adjust the angle guide height, loosen the lock lever

down and rotate the knob until the pointer points to the

desired scale graduation marked on the angle guide.

Then tighten the lock lever up to secure the angle guide.

The scale on the angle guide indicates the distance from

the top of the workpiece to the center of the blade thick-

ness.

The angle guide is removable from the fence according

to the need of your work. To remove the angle guide,

loosen the lock lever and turn the knob clockwise until it

comes out of the upper end of the fence.

Fence (Fig. 7 & 8)

NOTE:

• Remove the angle guide according to the need of your

work when using the tool with the angle of the fence

adjusted to other than 0°. When you need to use the

angle guide under the above condition, be sure to

adjust the depth of groove to get a proper depth.

The angle of the fence can be adjusted between 0° and

90° (positive stops at 0°, 45° and 90°). To adjust the

angle, loosen the lock lever and tilt the fence until the

pointer points to the desired graduation on the angle

scale. Then tighten the lock lever to secure the fence.

When the fence is set at 90°, both the distance from the

center of the blade thickness to the fence and the dis-

tance from the center of the blade thickness to the bot-

tom of the base are 10 mm.

Set plate (Fig. 9 & 10)

Use the set plate as shown in Fig. 9 & 10 when cutting

slots in thin workpieces.

Switch action (Fig. 11)

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the slide switch actuates

properly and returns to the “OFF” position when the

rear of the slide switch is depressed.

• Switch can be locked in “ON” position for ease of oper-

ator comfort during extended use. Apply caution when

locking tool in “ON” position and maintain firm grasp on

tool.

To start the tool, slide the slide switch toward the “I (ON)”

position. For continuous operation, press the front of the

slide switch to lock it.

To stop the tool, press the rear of the slide switch, then

slide it toward the “O (OFF)” position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Removing or installing the blade (Fig. 12)

CAUTION:

• When installing the plate joiner blade, mount the inner

flange with the side marked “22” facing toward you.

To remove the blade, loosen the clamp screw and open

the blade cover. Push the shaft lock and loosen the lock

nut using the lock nut wrench. To install the blade, first

mount the inner flange.

Then mount the blade and the lock nut. Securely tighten

the lock nut using the lock nut wrench. Close the blade

cover and tighten the clamp screw to secure the blade

cover.

CAUTION:

• Use only Makita lock nut wrench provided to remove or

install the blade.

• Always check the depth of groove after replacing the

blade. Readjust it if necessary.

Dust bag (Fig. 13)

To attach the dust bag, fit it onto the dust nozzle. If the

dust bag becomes an obstacle to your work, turn the dust

nozzle to change the dust bag position.

When the dust bag is about half full, switch off and

remove the battery cartridge. Remove the dust bag from

the tool and pull the bag’s fastener out. Empty the dust

bag by tapping it lightly to remove as much of the dust as

possible.

Size on stopper 0 10 20 S D MAX

Biscuit size 0 10 20 — — —

Depth of groove 8 mm 10 mm 12.3 mm 13 mm 14.7 mm 20 mm*

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita DPJ140 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info