691782
34
Verklein
Vergroot
Pagina terug
1/244
Pagina verder
34 ENGLISH
State of abnormality Probable cause (malfunction) Remedy
Thevacuumcleanerdoesnotrun
along with the switch operation of
the tool.
Thewirelessunitisnotinstalledinto
the tool.
Thewirelessunitisimproperlyinstalled
into the tool.
Install the wireless unit correctly.
Theterminalofthewirelessunitand/or
the slot is dirty.
Gently wipe off dust and dirt on the terminal of the
wireless unit and clean the slot.
Thewirelessactivationbuttononthe
tool has not been pushed.
Pushthewirelessactivationbuttonbrieyandmake
sure that the wireless activation lamp is blinking
in blue.
Thestand-byswitchonthevacuum
cleanerisnotsetto"AUTO".
Set the stand-by switch on the vacuum cleaner to
"AUTO".
More than 10 tools are registered to the
vacuum cleaner.
Perform the tool registration again.
If more than 10 tools are registered to the vacuum
cleaner, the tool registered earliest will be cancelled
automatically.
Thevacuumcleanererasedalltool
registrations.
Perform the tool registration again.
No power supply Supply the power to the tool and the vacuum
cleaner.
Thetoolandvacuumcleanerisaway
from each other (out of the transmission
range).
Get the tool and vacuum cleaner closer each other.
Themaximumtransmissiondistanceisapproxi-
mately 10 m however it may vary according to the
circumstances.
Radio disturbance by other appliances
which generate high-intensity radio
waves.
Keep the tool and vacuum cleaner away from the
appliances such as Wi-Fi devices and microwave
ovens.
Thevacuumcleanerrunswhilethe
tool's switch trigger is not pulled.
Other users are using the wireless
activation of the vacuum cleaner with
their tools.
Turnoffthewirelessactivationbuttonoftheother
tools or cancel the tool registration of the other
tools.
MAINTENANCE
WARNING: Always be sure that the tool is
switched off and batteries are removed before
attempting to perform inspection or maintenance.
Failure to removing the batteries and switch off the
tool may result in accidental start up of the tool which
mayresultinseriouspersonalinjury.
WARNING: Always be sure that the blade is
sharp and clean for the best and safest perfor-
mance.Attemptingacutwithadulland/ordirtyblade
may cause kickback and result in a serious personal
injury.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Adjusting the cutting angle
Thistooliscarefullyadjustedandalignedatthefactory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
Miter angle
Lower the handle fully and lock it in the lowered position
by the stopper pin. Push the carriage toward the guide
fence. Loosen the grip and the screws which secure the
pointer and miter angle scale.
►Fig.70: 1. Screw on pointer 2. Screws on miter
angle scale 3. Miter scale
Set the turn base to the 0° position using the positive
stopfunction.Squarethesideofthebladewiththeface
oftheguidefenceusingatriangularruleortry-square.
Whilekeepingthesquare,tightenthescrewsonthe
miteranglescale.Afterthat,alignthepointers(both
right and left) with the 0° position in the miter angle
scale and then tighten the screw on the pointer.
►Fig.71: 1.Triangularrule
Bevel angle
0° bevel angle
Push the carriage toward the guide fence and lock the
sliding movement by the stopper pin. Lower the handle
fully and lock it in the lowered position by the stopper
pinandthenloosentheknob.Turnthe0°adjusting
bolt two or three revolutions counterclockwise to tilt the
blade to the right.
►Fig.72: 1.0°Adjustingbolt2. Screw
Carefullysquarethesideofthebladewiththetop
surface of the turn base using the triangular rule, try-
square,etc.byturningthe0°adjustingboltclockwise.
Thentightentheknobrmlytosecurethe0°angleyou
have set.
►Fig.73: 1.Triangularrule2. Saw blade 3.Topsur-
face of turn base
Checkifthesideofthebladesquareswiththeturnbase
surface once again. Loosen the screw on the pointer.
Alignthepointerwith0°positioninthebevelangle
scale and then tighten the screw.
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS111 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS111 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 37,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info