691782
30
Verklein
Vergroot
Pagina terug
1/244
Pagina verder
30 ENGLISH
Crown molding stopper
Optional accessory
Crown molding stoppers allow easier cuts of crown
molding without tilting the saw blade. Install them on the
turnbaseasshowninthegures.
At right 45° miter angle
►Fig.52: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3.Turnbase4. Guide fence
At left 45° miter angle
►Fig.53: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3.Turnbase4. Guide fence
PositioncrownmoldingwithitsWALLCONTACTEDGE
againsttheguidefenceanditsCEILINGCONTACTEDGE
againstthecrownmoldingstoppersasshowninthegure.
Adjustthecrownmoldingstoppersaccordingtothesizeof
thecrownmolding.Tightenthescrewstosecurethecrown
molding stoppers. Refer to the table (C) for the miter angle.
►Fig.54: 1. Guide fence 2. Crown molding stopper
(a) (b) (c) (d)
12
1. Inside corner 2. Outside corner
Table (C)
Molding
position in
the gure
Miter angle Finished
piece
For inside
corner
(a) Right 45° Save the right
side of blade
(b) Left 45° Save the left
side of blade
For outside
corner
(c) Save the right
side of blade
(d) Right 45° Save the left
side of blade
Cutting aluminum extrusion
►Fig.55: 1. Vise 2. Spacer block 3. Guide fence
4.Aluminumextrusion5. Spacer block
When securing aluminum extrusions, use spacer blocks or pieces
ofscrapasshownintheguretopreventdeformationofthealu-
minum. Use a cutting lubricant when cutting the aluminum extru-
sion to prevent build-up of the aluminum material on the blade.
WARNING: Never attempt to cut thick or
round aluminum extrusions.Thickorroundalumi-
numextrusionscanbedifculttosecureandthework
may loosen during the cutting operation which may
resultinlossofcontrolandseriouspersonalinjury.
Groove cutting
WARNING: Do not attempt to perform this
type of cut by using a wider type blade or dado
blade.Attemptingtomakeagroovecutwithawider
blade or dado blade could lead to unexpected cutting
results and kickback which may result in serious
personalinjury.
WARNING: Be sure to return the stopper arm
to the original position when performing other
than groove cutting.Attemptingtomakecutswith
the stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which may
resultinseriouspersonalinjury.
For a dado type cut, perform as follows:
1. Adjustthelowerlimitpositionofthebladeusing
theadjustingscrewandthestopperarmtolimitthecut-
tingdepthoftheblade.Referto"Stopperarm"section
described on previously.
2. Afteradjustingthelowerlimitpositionoftheblade,
cut parallel grooves across the width of the workpiece
using a slide (push) cut.
►Fig.56: 1. Cut grooves with blade
3. Remove the workpiece material between the
grooves with a chisel.
Carrying tool
Before carrying, make sure to remove the batteries and
allmovablepartsofthemitersawaresecured.Always
check the following:
• Thebatteriesareremoved.
• Thecarriageisat0°bevelanglepositionand
secured.
• Thecarriageisloweredandlocked.
• Thecarriageisfullyslidtotheguidefenceand
locked.
• Theturnbaseisatthefullrightmiterangleposi-
tion and secured.
• Theholdersarestoredandsecured.
Carry the tool by holding both sides of the tool base as
showninthegure.
►Fig.57
WARNING: Stopper pin for carriage elevation
is for carrying and storage purposes only and not
for any cutting operations.Theuseofthestopper
pin for cutting operations may cause unexpected
movement of the saw blade resulting in kickback and
seriouspersonalinjury.
CAUTION: Always secure all moving portions
before carrying the tool. If portions of the tool move
or slide while being carried, loss of control or balance
mayoccurandresultinpersonalinjury.
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DLS111 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DLS111 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 37,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info