793614
10
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
10 ENGLISH
Error code
and status
symbol on
screen
Tool performance
and function
Tool status LED indicators/beeper status Action to be taken
LED indicators Beeper
-󰀩
fastening
The tool raises an alert for
incomplete fastening under the
following operating conditions.
(1): The trigger switch is
released before the pre-set
fastening torque has been
achieved.
(2): The tool stops automati-
cally after classifying fastening
errors.
(1): The LED
indicator lights
up in red for
approximately two
seconds.
(2): The LED

in yellow and red
alternately for
approximately two
seconds.
A long
beep
Retighten the screw.
Waiting function
between pre-set
fastening steps
The tool is sitting idle, after one
of the pre-set fastening steps
has been completed, waiting to
follow the next pre-set fasten-
ing step.
* A status symbol ( 
in the display screen.
The LED indicator
lights up in green.
- -
-Low-battery alert The battery is becoming low on
power, and the battery cartridge
needs to be recharged or
replaced with fully charged one.
The LED indicator

in red.
A series of
long beeps
Replace the battery
with fully charged
one.
-Error alert for heat
detection of motor
The motor temperature cannot
be monitored properly for a
number of technical reasons
including line breaks.
The LED indicator

in red.
A series
of short
beeps
Remove the battery
cartridge and cool
the tool down. If the
indicator remains lit,
ask your local Makita
Service Center for
repair.
Maintenance notice Maintenance notice will be
posted for optimum operational
reliability when the accu-
mulated maintenance count
reaches the pre-set number.
* A status symbol ( )
appears in the display screen
when the accumulated mainte-
nance count reaches the pre-
set “Stop Count” number.
The LED indicator

-Reset the mainte-
nance count in the
application software
designed for this
tool.
Alert for storage
disabled
Up to 1,000 fastening result
data can be saved in the tool
memory. The number of unread
data in the memory reaches to
the maximum.
* A status symbol ( )
appears in the display screen
when the storage capacity
reaches the maximum.
The LED indicator

-Load the fastening
result data saved
in the tool memory
using the application
software designed
for this tool.
-Error alert for data
communication with
computer
The tool raises an alert for
communication error in the
wired environment.
The LED indicator

-Link the tool again
with the application
software designed
for the tool after
restarting the
application.
-Status indicator for
data communication
with computer
The tool informs that data
communication has been
securely established in the
wired environment.
The LED indicator

- -
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DFT120T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DFT120T in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 18.78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info