600658
6
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
For DA301DB/DA391DB (Fig. 3)
Plug the battery charger into your power source.
Insert the battery cartridge so that the plus and minus
terminals on the battery cartridge are on the same
sides as their respective markings on the battery
charger. Insert the cartridge fully into the port so that
it rests on the charger port floor.
When the battery cartridge is inserted, the charging
light will come on and charging will begin. The charg-
ing light will keep lighting up steadily during charging.
When charging is completed, the charging light goes
out. The charging time is approx. 100 minutes. If you
leave the battery cartridge in the charger after the
charging cycle is complete, the charger will switch into
its ‘trickle charge (maintenance charge)’’ mode which
will last approximately 24 hours.
After charging, unplug the charger from the power
source.
Battery type
Capacity
(mAh)
Number of
cells
7033 2,200 6
9033 2,200 8
CAUTION:
If you charge a battery cartridge from a just-
operated machine or a battery cartridge which has
been left in a location exposed to direct sunlight for
a long time, the charging light may flash in red color.
If this occurs, wait for a while. Charging will begin
after the battery cartridge cools.
Any of the following conditions indicates damage to
the charger and/or battery cartridge. Ask your
Makita Authorized or Factory Service Center to
check them.
1) The charging light does not light up or flash (red)
when the battery is inserted in the charger port.
2) Charging is not completed at even more than
three hours after red light comes ON at start of
charging.
Trickle charge (Maintenance charge)
If you leave the battery cartridge in the charger to
prevent spontaneous discharging after full charge,
the charger will switch into its ‘‘trickle charge (main-
tenance charge)’’ mode and keep the battery car-
tridge fresh and fully charged.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop machine operation and charge the
battery cartridge when you notice less machine
power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C 40°C (50°F 104°F).
Let a hot battery cartridge cool down before
charging it.
Installing or removing drill bit or driver bit
Important:
Always be sure that the machine is switched off and
the battery cartridge is removed before installing or
removing the bit.
For DA301D/DA301DB (Fig.4&6)
To install the bit, place it in the chuck as far as it will
go. Tighten the chuck by hand. Place the chuck key in
each of the three holes and tighten clockwise. Be sure
to tighten all three chuck holes evenly. To remove the
bit, turn the chuck key counterclockwise in just one
hole, then loosen the chuck by hand.
After use, return the chuck key to the storage cavity
on the machine.
For DA391D/DA391DB (Fig. 5)
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far
as it will go. Hold the ring firmly and turn the sleeve
clockwise to tighten the chuck. To remove the bit, hold
the ring and turn the sleeve counterclockwise.
Switch action
(Fig. 7 for DA301D/DA301DB & Fig. 8 for
DA391D/DA391DB)
CAUTION:
Before inserting the battery cartridge into the
machine, always check to see that the switch trigger
actuates properly and returns to the ‘‘OFF’’ position
when released.
Always check the direction of rotation before opera-
tion.
Use the reversing switch lever only after the
machine comes to a complete stop. Changing the
direction of rotation before the machine stops may
damage the machine.
When not operating the machine, keep the revers-
ing switch lever in the neutral position.
Set the reversing switch lever just in front of the switch
trigger to
/ ‘‘FWD’’ side for clockwise rotation or
/ ‘‘REV’’ side for counterclockwise rotation. To
start the machine, simply pull the trigger. Machine
speed is increased by increasing pressure on the
trigger. Release the trigger to stop. When the revers-
ing switch lever is in the neutral position, the machine
will not start even if you pull the trigger.
Drilling operation
Drilling in wood
When drilling in wood, best results are obtained with
wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole,
make an indentation with a center punch and ham-
mer at the point to be drilled. Place the point of the
bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The
exceptions are iron and brass which should be
drilled dry.
6
DA301D/DA391D (Eng) (’100. 3. 8)
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DA391DB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DA391DB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info