600685
7
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
7
Switch action (Fig. 3)
To start the cleaner, simply press the “HIGH/LOW” but-
ton. To switch off, press the “OFF” button. To change the
cleaner speed, press the “HIGH/LOW” button. The first
press on this button is for high speed and the second
press for low speed and then each press on this button
repeats the high/low speed cycle alternatively.
ASSEMBLY
CAUTION:
Always be sure that the cleaner is switched off and the
battery cartridge is removed before carrying out any
work on the cleaner.
Any work with the battery cartridge being installed on
the cleaner may cause a personal injury or damage to
the objects around the cleaner.
Installing dust bag (Fig. 4, 5, 6 & 7)
Hold the square section of the dust bag joint and fit the
pins inside the dust bag joint to the notches in the dust
outlet of the cleaner and then insert and turn it clockwise
all the way until it stops.
At this time, make sure that the fastener part on the dust
bag faces upward.
NOTE:
• When the dust bag joint and the ring inside the dust
bag come off, install as follows.
(1) Align the dust bag joint with the seam of the dust
bag and install it so that its protrusion faces
upward.
(2) Tighten the ring inside the dust bag firmly so that
the pins and the ring are positioned as shown in
the figure.
Installing the shoulder strap (Fig. 8)
Attach one end hook of the shoulder strap onto the ring
in the front of the cleaner and thrust the other end of the
strap through the band of the dust bag and then attach
the other end hook as shown in the figure.
Adjusting the shoulder strap (Fig. 9)
To adjust the length of the shoulder strap, pull it out to
your desired length and pull the strap in the direction of
arrow as shown in the figure.
Connecting the hose (Fig. 10)
CAUTION:
Do not force the hose to bend it and/or stamp it.
Forcing and/or stamping the hose may cause deforma-
tion or damage to the hose.
Do not pull the hose to carry the cleaner. Pulling the
hose may cause deformation or damage to the hose.
Insert the “A” end of the hose to the suction opening of
the cleaner and turn it clockwise all the way until it locks.
Attach the cuff on the “B” end of the hose and then con-
nect it to the dust outlet of an power tool.
Replacing the front cuff (Fig. 11)
Change the front cuff of the hose according to the dust
outlet size of a power tool you use.
To remove the front cuff, hold the hose and turn it coun-
terclockwise.
To mount the front cuff, turn it clockwise and then screw it
in until it stops.
OPERATION
WARNING:
Do not use the shoulder strap when working in a high
place.
When using the cleaner as a stationary cleaner, place it
on a flat and stable surface.
Vacuum cleaner (Fig. 12 & 13)
When using the cleaner as a portable cleaner, cross-
hanging the shoulder strap before the breast is difficult to
drop the cleaner.
NOTE:
Long cut-off decorative paper that may be produced by
plaster board cutting work depending on the conditions
of workpiece to be cut and that may be stuffed inside
the hose may cause the hose suction blocking. When
this occurs, change the cutting depth setting of power
tool to deeper depth, which will relieve the hose suction
blocking.
CAUTION:
When the dust bag is just new, dust may come out of its
surface. Using it a few times will minimize the dust leak
from the surface.
Operation of the cleaner with a nozzle or a dust
bag being installed
WARNING:
Always be sure that the cleaner is switched off and
the battery cartridge is removed before installing or
removing the nozzle or any other attachment on the
cleaner. Failure to switch off and remove the battery
cartridge may result in serious personal injury.
NOTE:
Before the blower mode operation immediately after
the cleaner mode operation, remove all remaining dust
from the cleaner due to possible blow out of dust.
Using as a blower (Fig. 14)
Install the nozzle onto the outlet (air vent) without fail.
To install the nozzle, fit the pin protruding from the
inside of nozzle to one of the cleaner notches and
then turn the nozzle clockwise securely.
To remove the nozzle, turn counterclockwise and pull
it out.
Direct the top point of the cleaner and then switch
on.
Emptying the dust bag
WARNING:
Always be sure that both the cleaner and a con-
nected power tool are switched off and the battery
cartridge is removed and the power tool, if corded
tool, is unplugged before installing or removing the
dust bag on the cleaner and emptying the dust bag
(made of cloth). Failure to switch off, remove the bat-
tery cartridge and unplug the connected power tool
may result in electric shock and serious personal injury.
When the dust bag is about half full, remove the dust
bag from the cleaner and pull the fastener out. Empty
the dust bag of its contents, tapping it lightly so as to
remove particles adhering to the insides which might
hamper further collection.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita BVC350 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita BVC350 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 1,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info