Handleiding Makita BTD136 (pagina 8 van 64) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens)

598621

Verklein

Vergroot

Pagina terug

1/64

Pagina verder

Indicating the remaining battery capacity (Fig. 8)

When you pull the switch trigger, the LED display shows

the remaining battery capacity.

The remaining battery capacity is shown as the following

table.

012273

NOTE:

• When the LED display goes off, the tool is turned off to

save the battery power. To check the remaining battery

capacity, slightly pull the switch trigger.

• The LED display goes off approximately one minute

after releasing the switch trigger.

• When the tool is overheated, the light flashes once per

second for one minute, and then the LED display goes

off. In this case, cool down the tool before operating

again.

• When the LED display lights up and the tool stops even

with a recharged battery cartridge, cool down the tool

fully. If the status will not change, stop using and have

the tool repaired by a Makita local service center.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver bit or socket bit

Use only bits that has inserting portion shown in the fig-

ure. (Fig. 9)

For tool with shallow bit hole

006348

For tool with deep bit hole

011405

Procedure 1 (Fig. 10)

For tool with normal sleeve

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit.

For tool with one-touch type sleeve

To install the bit, insert the bit into the sleeve as far as it

will go.

Procedure 2 (Fig. 11)

In addition to the Procedure 1 above, insert the bit-piece

into the sleeve with its pointed end facing in.

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

• When it is difficult to insert the bit, pull the sleeve and

insert it into the sleeve as far as it will go.

• After inserting the bit, make sure that it is firmly

secured. If it comes out, do not use it.

Hook (Fig. 12)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool hous-

ing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

OPERATION

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the figures.

(Fig. 13)

Model BTD136 (Fig. 14 & 15)

Model BTD147 (Fig. 16 & 17)

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

NOTE:

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• When fastening M8 or smaller screw, choose a proper

impact force and carefully adjust pressure on the

switch trigger so that the screw is not damaged.

• Hold the tool pointed straight at the screw.

• If the impact force is too strong you tighten the screw

for a time longer than shown in the figures, the screw or

the point of the driver bit may be overstressed,

stripped, damaged, etc. Before starting your job,

always perform a test operation to determine the

proper fastening time for your screw.

The fastening torque is affected by a wide variety of fac-

tors including the following. After fastening, always check

the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

LED indicator status Remaining battery capacity

About 50% or more

About 20% – 50%

About less than 20%

A = 12 mm

B = 9 mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A = 17 mm

B = 14 mm

To install these types of bits, follow the

procedure (1).

A = 12 mm

B = 9 mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for

installing the bit.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita BTD136 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info