Handleiding Makita BLM430 (pagina 21 van 100) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens)

598579

Verklein

Vergroot

Pagina terug

1/100

Pagina verder

ASSEMBLY

WARNING:

• Always be sure that the lock key and battery car-

tridge are removed before carrying out any work on

the mower. Failure to remove the lock key and the bat-

tery cartridge may result in serious personal injury from

accidental start-up.

• Never start the tool unless it is completely assem-

bled. Operation of the tool in a partially assembled

state may result in serious personal injury from acci-

dental start-up.

Installing the handle (Fig. 12, 13, 14, 15, 16 & 17)

WARNING:

• When installing handles, position the wires so that they

are not caught by anything in between the handles.

1. Loosen the clamping screws (two pcs).

Expand the lower handle to its both sides and with it

expanded in that position pivot it backward and then fit it

in the groove in the deck.

2. Tighten the clamping screws on both sides to secure

the lower handle.

3. Raise the upper handle and align the screw holes in

the upper handle with those in the lower handle and

then secure it with the supplied screws and clamp-

ing nuts.

NOTE:

• At this time, keep a firm grip on the upper handle so

that it does not drop off your hand.

NOTE:

• Install the upper handle so that the direction of the

upper handle and the power supply cord are positioned

as shown in the figure.

NOTE:

• The upper handle has two holes each on both sides.

Using the different position holes for the screws and

clamping nuts allows the handle height adjustment.

Removing or installing the blade (Fig. 18 & 19)

WARNING:

• Always remove the lock key and battery cartridge when

removing or installing the blade. Failure to remove the

lock key and battery cartridge may cause a serious

injury.

• The blade coasts for a few seconds after releasing the

switch. Make sure that the blade has come to a com-

plete stop.

• Always wear gloves when handling the blade.

1. Put the mower on its side so that the mowing height

adjusting lever is placed on the upper side.

2. To lock the blade, insert a screwdriver available or

the similars in market into a hole in the mower.

3. Loosen the bolt counterclockwise with the wrench.

4. Remove the bolt, outer flange, blade and inner

flange in order.

To install the blade, take the blade removal procedure in

reverse.

WARNING:

• Install the inner flange, the blade and the outer flange

carefully as these have a top/bottom facing.

• Tighten the bolt clockwise firmly to secure the blade.

• Put the blade so that the blade side with a rotational

direction arrow faces outward.

• Make sure that the blade is installed securely.

• Always take away the screwdriver or similars inserted

in a hole to lock the blade.

Installing the grass basket (Fig. 20 & 21)

Remove the lock key.

Raise the rear guard of the mower unit and hook the

grass basket on the groove of the mower unit.

OPERATION

Mowing

WARNING:

• Before mowing, clear away sticks and stones from

mowing area. Furthermore, clear away any weeds from

mowing area in advance.

• Always wear the safety goggles or safety glasses with

side shields when operating the mower.

Firmly hold the lawn mower handle with both hands

when mowing.

The front wheel outside edges of the main unit provide a

guideline to mowing width. Using the two front wheel out-

side edges as a guideline, mow in strips, overlapping by

one half to one third the previous strip, to mow the lawn

evenly.

Periodically check the level of the grass basket, and

empty before it becomes full. Before every periodical

checks, be sure to stop the mower and remove the lock

key and the battery cartridge.

NOTE:

• Using the lawn mower with the grass basket full pre-

vents smooth blade rotation and places an extra load

on the motor, which may cause breakdown.

Mowing a long-grass lawn (Fig. 22)

Do not try to cut long grass all in one go. Instead, mow

the lawn in stages, leaving it for a day or two between

mows, until the lawn is evenly short.

NOTE:

• Mowing long grass to a short length all in one go may

cause the grass to die and/or block up the inside of the

main unit.

Emptying the grass basket (Fig. 23)

WARNING:

• To reduce a risk of accident, regularly check the grass

basket for any damage or weakened strength and

replace it if necessary.

1. Release the switch lever.

2. Remove the lock key.

3. Open the rear guard and take out the grass basket

with its handle.

4. Empty the grass basket.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita BLM430 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Makita BLM430

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info