Handleiding Makita BFT043F (pagina 6 van 48) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens)

598473

Verklein

Vergroot

Pagina terug

1/48

Pagina verder

Adjusting the fastening torque (Fig. 6)

When you wish to drive machine screws, hex bolts, etc.

with the predetermined torque, adjust the fastening torque

as follows.

1. First remove the battery cartridge from the tool.

2. Loosen and remove the screw that secures the ring.

3. Rotate the ring in the front of the tool by hand so that a

hole can be seen below the ring.

4. Place the battery cartridge in place and pull the switch

trigger. Release it so that the adjust ring rotates and

the hole becomes visible as illustrated. And then

remove the battery cartridge. (Fig. 7)

5. Use an optional adjust grip to adjust the fastening

torque. Insert the pin of the adjust grip into the hole in

the front of the tool. And then, turn the adjust grip

clockwise to set a greater fastening torque, and

counterclockwise to set a smaller fastening torque.

6. Align the yellow line with your desired number on the

fastening torque scale.

7. Insert the battery cartridge and be sure that a

fastening torque has been set up by using a fastening

torque tester.

8. Rotate the ring in the front of the tool and then tighten

the screw to secure the ring.

NOTE:

• Numbers on the fastening torque scale are a guideline

to set up your desired fastening torque.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing driver bit or socket

bit (Fig. 8)

Use only bits that have inserting portions shown in the

figure.

For tool with shallow bit hole

For tool with deep bit hole

1. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit. (Fig. 9)

2. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit-piece and bit into the sleeve

as far as it will go. The bit-piece should be inserted

into the sleeve with its pointed end facing in. Then

release the sleeve to secure the bit. (Fig. 10)

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

Warning for battery

cartridge capacity

This indicates the appropriate time to

replace the battery cartridge when

the battery power becomes low.

Flickers in red slowly.

A series of long

beeps

Replace the battery

with fully charged

one

Checking the

remaining battery

capacity, Autostop

This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Lights up in red. A long beep

Replace the battery

with fully charged

one

Check the LED

indicator, light and

beeper operation

This function works to check the

proper operation of the LED indicator,

light and beeper when a battery

cartridge has been inserted into the

tool.

Lights up first in

green, next red.

(And then the light

comes on.)

A series of very

short beeps

—

Anti-reset of

controller

This function works when an

abnormal drop of the battery voltage

occurs for some reason, and the tool

stops.

Flickers in red and

green alternatively.

A series of short

beeps

Replace the battery

with fully charged

one

Overheat

This function works when the

temperature of the controller goes up

very highly, and the tool stops.

Flickers in red

quickly.

A series of short

beeps

Remove the battery

cartridge

immediately and

cool the tool down.

Operation error of the

switch trigger

This function works to avoid the tool’s

immediate start upon insertion of

battery cartridge into the tool with the

switch trigger being pulled.

Flickers in red and

green alternatively.

A series of short

beeps

Release the switch

trigger.

Function Status

Status of the LED indicator/beeper

Action to be taken

LED indicator Beeper

A=12 mm

B=9 mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A=17 mm

B=14 mm

To install these types of bits, follow the

procedure (1).

A=12 mm

B=9 mm

To install these types of bits, follow

the procedure (2).

(Note) Bit-piece is necessary for installing

the bit.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita BFT043F Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info