598404
9
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
9
Ask Makita's Authorized service centers for periodical
inspection of the tool.
To maintain product SAFETY and RELIABILITY,
maintenance and repairs should be performed by
Makita Authorized Service Centers, always using
Makita replacement parts.
Use only pneumatic tool oil specified in this manual.
Never connect tool to compressed air line where the
maximum allowable pressure of tool cannot be
exceeded by 10%. Make sure that the pressure
supplied by the compressed air system does not
exceed the maximum allowable pressure of the
fastener driving tool. Set the air pressure initially to the
lower value of the recommended allowable pressure.
Do not attempt to keep the trigger contact element
depressed with tape or wire. Death or serious injury
may occur.
Always check contact element as instructed in this
manual. Screws may be driven accidentally if the safety
mechanism is not working correctly.
SAVE THESE INSTRUCTIONS.
INSTALLATION
Selecting air hose (Fig. 2)
Use a high pressure resistant air hose.
Use an air hose as large and as short as possible to
assure continuous, efficient screw-driving operation.
CAUTION:
Low air output of the compressor, or a long or smaller
diameter air hose in relation to the screw-driving
frequency may cause a decrease in the driving
capability of the tool.
Lubrication (Fig. 3)
To insure maximum performance, install an air set (oiler,
regulator, air filter) as close as possible to the tool.
Adjust the oiler so that one drop of oil will be provided for
every 30 screws.
When an air set is not used, oil the tool with pneumatic
tool oil by placing 2 (two) or 3 (three) drops into the air
fitting. This should be done before and after use. For
proper lubrication, the tool must be fired a couple of times
after pneumatic tool oil is introduced. (Fig. 4)
FUNCTIONAL DESCRIPTION
CAUTION:
When adjusting driving depth, always lock the trigger
and disconnect the air hose.
Adjuster (drive depth adjuster) Operating
Method (Fig. 5 & 6)
CAUTION:
When adjusting driving depth, always lock the trigger
and disconnect the air hose.
This driver is equipped with an adjuster for adjusting
screw driving depth.
Turn the adjuster to adjust driving depth. Driving
adjustment range is 6mm. (one turn of adjuster adjusts
depth by approximately 0.8mm.)
Hook (Fig. 7)
CAUTION:
When using the hook, or changing its position, always
lock the trigger, and disconnect the air hose.Do not
fasten hook onto waist belt, etc.
If hook becomes unfastened and the driver drops,
driver may operate by mistake, and lead to injury.
The hook is useful for hanging up the driver temporarily.
The mounting position of the hook on the driver can be
changed.
Remove the hook mounting screw, change position of
hook, and re-secure screw.
Switcher Mode Selection (Fig. 8)
This driver is equipped with a switcher to enable selection
of mode for optimum driving according to the material of
the workpiece. Set to mode positions shown in “Switching
Mode Chart” below for optimum use. Thoroughly turn the
knob until it clicks to a halt properly at either position (1) or
(2). If the driver is used with the switcher in a position
between (1) and (2), driver components may become
damaged, and/or normal performance not achieved.
Suitable for use on general plasterboard with thicknesses
of 9.5mm, 12.5mm and 15mm.
Steel sheet backing up to 0.8mm thick can be worked on
(screws cannot be driven into layered steel sheet
backing).
Always use Makita genuine linked screws.
We recommend that in normal situations the driver be
used in Switching Mode (1), and set to Switching Mode
(2) when screws cannot be driven for lack of power.
ASSEMBLY
Loading Screws
CAUTION:
Always disconnect air hose from main unit before
loading screws.
If the main unit is operated by mistake, it may lead to
personal injury.
Steel sheet backing
Steel sheet thickness
0.8 mm
(2) (2) (2)
Steel sheet thickness
0.6 mm
(1) (1) (1).(2)
Steel sheet thickness
0.6 mm
(1) (1) (1)
Wood backing (1) (1) (1) (1)
Screw length 25 mm 28 mm 32 mm 41 mm
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita AR410HR bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita AR410HR in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 1,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info