601098
11
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
TOOL INSTALLATION INSTRUCTIONS AND USE
Selecting compressor
The air compressor must comply with the requirements of
Select a compressor that has ample pressure and air output
to
assure cost-efficient operation. The graph shows the
relation between nailing frequency, applicable pressure and
compressor air output. Thus, for example,
if
nailing takes
place at a rate of approximately
40
times per minute at a
compression of
6
kgf/cm2G (85 PSIG), a compressor with
an air output over 3 ft3/minute is required. Pressure
regulators must be used to limit air pressure to the rated
pressure of the tool where air supply pressure exceeds the
tool’s rated pressure. Failure to do
so
may result in serious
injury to tool operator or persons in the vicinity.
ANSI B19.3
-
1981.
Selecting air hose
Use an air hose as large and as short as possible to assure
continuous, efficient nailing operation. With an air pressure
of
5 kgf/cm2G (70 PSIG), an air hose with an internal
diameter of over
8.5
mm
(5/16”)
and a length of less than
20
m
(6.6
ft.) is recommended when the interval between
each nailing is
0.5
seconds. Air supply hoses shall have a
minimum working pressure rating of 10.7 kgf/cm2G (150
PSIG) or
150
percent of the maximum pressure produced
in the system whichever is higher.
Nailing
frequency
(timedmin.)
CAUTION:
Low air output of the compressor, or a long or smaller diameter air hose in relation to the nailing frequency
may cause a decrease in the driving capability of the tool.
Lubrication
To insure maximum performance, install an air set (oiler,
regulator, air filter) as close as possible to the tool. Adjust
the oiler
so
that one drop of oil will be provided for every
30 nails.
When
n ir et is not used,
oil
the tool with pneumatic tool
oil by placing
2
(two) or 3 (three) drops into the air fitting.
This should be done before and after use. For proper lubri-
cation, the tool must be fired a couple of times after pneu-
matic tool oil is introduced.
Pneumatic tool oil
11
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita AN922 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita AN922 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,35 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info