598394
6
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
6
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Intended use
ENE072-1
The tool is intended for securing a thin steel plate to the
concrete.
IMPORTANT SAFETY
INSTRUCTIONS ENB115-1
WARNING: WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1. For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
2. Always wear safety glasses to protect your eyes from
dust or pin injury.
WARNING:
It is an employer’s responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
3. For Australia and New Zealand only
Always wear safety glasses and face shield to protect
your eyes from dust or pin injury. The safety glasses
and the face shield should conform with the
requirements of AS/NZS 1336.
WARNING:
It is an employer’s responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
(Fig. 1)
4. Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
5. Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when under
the influence of alcohol, drugs or the like.
6. General Tool Handling Guidelines:
(1) Always assume that the tool contains fasteners.
(2) Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
(3) Do not activate the tool unless the tool is placed
firmly against the workpiece.
(4) Respect the tool as a working implement.
(5) No horseplay.
(6) Do not hold or carry the tool with a finger on the
trigger.
(7) Do not load the tool with fasteners when any one
of the operating controls is activated.
(8) Do not operate the tool with any power source
other than that specified in the tool operating/
safety instructions.
7. An improperly functioning tool must not be used.
8. Sparks sometimes fly when the tool is used. Do not
use the tool near volatile, flammable materials such as
gasoline, thinner, paint, gas, adhesives, etc.; they will
ignite and explode, causing serious injury.
9. The area should be sufficiently illuminated to assure
safe operations. The area should be clear and litter-
1. Safety glasses
2. Face shield
3. Compressor air output per minute
4. Nailing frequency
5. Adjuster
6. Too deep
7. Flush
8. Too shallow
9. Screw
10. Hook
11. Contact element
12. Nose adapter
13. LOCK position
14. FREE position
15. Latch lever
16. Door
17. Driver channel
18. Trigger
19. Workpiece
20. Thin steel plate
21. Penetration amount into concrete
22. Cap
23. Drain cock
24. Air filter
25. Oiler
26. Pneumatic oil
27. Thinner
28. Stove
Model AN250HC
Air pressure 1.18 - 2.26 MPa (11.8 - 22.6 bar)
Nail length
19 mm - 25 mm
Sheet-collated coil pin
Nail capacity 100 pcs
Min. hose diameter 5 mm
Dimensions (L X W X H) 295 mm X 128 mm X 291 mm
Net weight 2.1 kg
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita AN250HC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita AN250HC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 1,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info