Handleiding Makita 9237CB (pagina 6 van 52) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens)

691005

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

Speed adjusting dial (Fig. 3)

The tool speed can be changed by turning the speed

adjusting dial to a given number setting from 1 to 6. (At

the time when the switch trigger is fully pulled.)

Higher speed is obtained when the dial is turned in the

direction of number 6. And lower speed is obtained when

it is turned in the direction of number 1.

Refer to the table for the relationship between the

number settings on the dial and the approximate tool

speed.

014945

CAUTION:

• If the tool is operated continuously at low speeds for a

long time, the motor will get overloaded, resulting in

tool malfunction.

• The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

• Always install the loop handle or the side grip.

Removing or installing head cover (Fig. 4)

To remove the head cover, perform the following steps:

1. Remove the screw on the head cover with

screwdriver.

2. Remove the head cover as shown in the figure.

To install the head cover, perform the above steps in

reverse.

Installing loop handle

CAUTION:

• Always be sure that the loop handle is installed

securely before operation.

Always install the loop handle on the tool before

operation. Hold the tool’s switch handle and the loop

handle firmly with both hands during operation.

Install the loop handle so that its protrusion will fit into the

matching hole in the gear housing. (Fig. 5)

Install the bolts and tighten them with the hex wrench.

The loop handle can be installed in two different

directions as shown in the figures whichever is

convenient for your work. (Fig. 6 & 7)

For tools which are equipped with a backing pad.

Installing or removing the wool pad (optional

accessory) (Fig. 8)

To install the wool pad, first remove all dirt or foreign

matter from the backing pad. Press the shaft lock and

screw the backing pad onto the spindle. Insert the sleeve

18 into the center hole of the backing pad.

Using the sleeve 18 as a positioning guide, install the

wool pad on the backing pad with the sleeve 18 inserted

through the center hole of the wool pad. Then remove

the sleeve 18 from the backing pad.

To remove the wool pad, just tear it off the backing pad.

Then unscrew the backing pad while pressing the shaft

lock.

For tools which are equipped with a rubber pad.

Installing or removing the wool bonnet (optional

accessory)

Mount the rubber pad onto the spindle. Screw the lock

nut onto the spindle. (Fig. 9)

To tighten the lock nut, press the shaft lock firmly so that

the spindle cannot revolve, then use the lock nut wrench

and securely tighten clockwise.

To remove the rubber pad, follow the installation

procedure in reverse. (Fig. 10)

Fit the wool bonnet over the rubber pad. Tie a bow knot

and tuck the knot and any loose strings between the wool

bonnet and the rubber pad. (Fig. 11)

Installing side grip (handle) (optional accessory)

(Fig. 12)

CAUTION:

• Always be sure that the side grip is installed securely

before operation.

Screw the side grip securely on the position of the tool as

shown in the figure.

OPERATION

Polishing operation (Fig. 13)

CAUTION:

• Always wear safety glasses or a face shield during

operation.

Hold the tool firmly. Turn the tool on and then apply the

wool pad/bonnet to the workpiece.

In general, keep the wool pad/bonnet at an angle of

about 15 degrees to the workpiece surface.

Apply slight pressure only. Excessive pressure will result

in poor performance and premature wear to wool pad/

bonnet.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Cleaning the dust cover (Fig. 14)

Clean the dust cover when necessary as following steps:

1. Remove the screw on the dust cover.

2. Remove the dust cover.

3. Wipe the dust cover to remove dirt.

4. Align the hook of the dust cover with groove on the

handle.

5. Tighten the dust cover with the screw.

If the dust cover is broken or becomes extremely dirty,

replace it.

Number min

–1

(RPM)

1 600

2 900

31,500

42,100

52,700

63,200

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita 9237CB Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info