79032
6
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
OPERATING INSTRUCTIONS
Installing loop handle
Important:
Always be sure that the tool is switched off and
unplugged before installing the loop handle.
Always install the loop handle on the tool before
operation. Hold the tool’s switch handle and the loop
handle firmly with both hands during operation.
Install the loop handle so that its protrusion will fit into
the matching hole in the gear housing. (Fig. 1)
Install the bolts and tighten them with the hex wrench.
The loop handle can be installed in two different
directions as shown in Fig.2&3, whichever is con-
venient for your work. (Fig.2&3)
Shaft lock (Fig. 4)
Press the shaft lock to prevent spindle rotation when
installing or removing accessories such as wool pads.
CAUTION:
Never actuate the shaft lock when the spindle is
moving. The tool may be damaged.
Installing or removing wool pad (Fig.1&5)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wool pad.
To install the wool pad, first remove all dirt or foreign
matter from the backing pad. Press the shaft lock and
screw the backing pad onto the spindle. Insert the
sleeve 18 into the center hole of the backing pad.
Using the sleeve 18 as a positioning guide, install the
wool pad on the backing pad with the sleeve 18
inserted through the center hole of the wool pad. Then
remove the sleeve 18 from the backing pad. To
remove the wool pad, just tear it off the backing pad.
Then unscrew the backing pad while pressing the
shaft lock.
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
‘‘OFF’ position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger.
Release the trigger to stop. For continuous operation,
pull the trigger and then push in the lock button. To
stop the tool from the locked position, pull the trigger
fully, then release it.
Speed adjusting dial (Fig. 7)
The tool speed can be infinitely adjusted between
600 rpm and 3,000 rpm (rpm at the time when the
switch trigger is fully pulled) by turning the speed
adjusting dial to a given number setting from 1 to 6.
Higher speed is obtained when the dial is turned in the
direction of number 6; lower speed is obtained when
it is turned in the direction of number 1. Refer to the
table below for the relationship between the number
settings on the dial and the approximate tool speed.
Number RPM (min
–1
)
1–2 600–900
2 3 900 1,500
3 4 1,500 2,100
4 5 2,100 2,700
5 6 2,700 3,000
CAUTION:
If the tool is operated continuously at low speeds for
a long time, the motor will get overloaded and
heated up.
The speed adjusting dial can be turned only as far
as 6 and back to 1. Do not force it past 6 or 1, or the
speed adjusting function may no longer work.
Polishing operation (Fig. 8)
CAUTION:
Always wear safety glasses or a face shield during
operation.
Pull the trigger and turn the speed adjusting dial until
you obtain the appropriate speed for your work. When
polishing, keep the wool pad at an angle of about 15°
to the workpiece surface.
6
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita 9227 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita 9227 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Noors als bijlage per email.

De handleiding is 0,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info