Handleiding Makita 6914 dwb (pagina 5 van 13) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

386594

Verklein

Vergroot

Pagina terug

1/13

Pagina verder

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the machine before insertion or removal of the battery cartridge.

• To remove the battery cartridge, withdraw it from the machine while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into

place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the

machine, causing injury to you or someone around you.

• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted

correctly.

Installing or removing bit

Important:

Always be sure that the machine is switched off and the battery cartridge is removed before installing or removing the

bit.

Use only the driver bit or socket bit shown in the table below.

Do not use any other driver bit or socket bit.

(1) To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit. (Fig. 2)

(2) To install the bit, pull the sleeve in the direction of the arrow and insert the bit-piece and the bit into the sleeve as far

as it will go. The bit-piece should be inserted into the sleeve with its pointed end facing in. Then release the sleeve

to secure the bit. (Fig. 3)

To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly.

NOTE:

If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not

be secured. In this case, try re-inserting the bit according to the instructions above.

Switch action (Fig. 4)

CAUTION:

Before inserting the battery cartridge into the machine,

always check to see that the switch trigger actuates prop-

erly and returns to the “OFF” position when released.

To start the machine, simply pull the trigger. Machine

speed is increased by increasing pressure on the trigger.

Release the trigger to stop.

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the machine comes

to a complete stop. Changing the direction of rotation

before the machine stops may damage the machine.

• When not operating the machine, always set the

reversing switch lever to the neutral position.

This machine has a reversing switch to change the direc-

tion of rotation. Depress the reversing switch lever from

the A side for clockwise rotation or from the B side for

counterclockwise rotation. When the switch lever is in the

neutral position, the switch trigger cannot be pulled.

Operation (Fig.6, 7 & 8)

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in Fig.6 for

machine screw, Fig. 7 for standard bolt or Fig. 8 for high

tensile bolt.

Hold the machine firmly and place the point of the driver

bit in the screw head. Apply forward pressure to the

machine to the extent that the bit will not slip off the

screw and turn the machine on to start operation.

NOTE:

• When fastening screw M8 or smaller, carefully adjust

pressure on the switch trigger so that the screw is not

damaged.

• Hold the machine pointed straight at the screw.

• If you tighten the screw for a time longer than shown in

the figures, the screw or the point of the driver bit may

be overstressed, stripped, damaged, etc. Before start-

ing your job, always perform a test operation to deter-

mine the proper fastening time for your screw. When

fastening a standard screw in a steel plate, the proper

fastening torque can be obtained in an extremely short

time (approx. 0.1– 0.2 seconds). Turn the machine off

as soon as the impact sound is heard.

A= 17mm

B= 14mm

To install these types of bits, follow the procedure (1).

(Note) Makita bits are these types.

A= 12mm

B = 9mm

To install these types of bits, follow the procedure (2).

(Note) Bit-piece is necessary for installing the bit.

For European and North & South American countries

Use only these types of bits. Follow the procedure (1).

(Note) Bit-piece is not necessary.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita 6914 dwb Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info