Handleiding Makita 6841R (pagina 6 van 36) (Duits, Engels, Pools)

690977

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

Fig.5

Setting for desired screw length

Fig.6

There are 3 positive-lock screw length settings. To obtain

the desired setting, pull out the stopper base while

depressing the lever until you see the number of the

desired screw length (indicated on the plate) appear to

rest on the very top edge of the casing. See the table

below for the relation between the number indicated on

the plate and the respective screw length ranges.

25/28 25 mm - 28 mm

32 28 mm - 35 mm

41 35 mm - 41 mm

Number indicated on the plate

Screw length range

009832

Adjusting the driving depth

Fig.7

Depress the stopper base as far as it will go. While

keeping it in this position, turn the adjusting knob until the

bit tip projects approx. 5 mm from the stopper base. Drive

a trial screw. If the screw head projects above the surface

of the workpiece, turn the adjusting knob in the "A"

direction; if the screw head is counter-sunk, turn the

adjusting knob in the "B" direction.

Installing screw strip

1. Squeeze the lock lever with fingers and open the

magazine cap.

Fig.8

Roll up the screw strip in a form of coil

counterclockwise and place it inside the magazine.

Fig.9

3. Run the end of the screw strip on the slotted

passage starting from above the magazine.

Fig.10

4. Close the magazine cap while squeezing the lock

lever with fingers.

Fig.11

5. Insert the top end of the screw strip into the portion

A of the feeder box and feed it in the direction of

the arrow.

Fig.12

6. Set the screw strip so that the first screw of the

strip seats with a space for one screw left before

the screw-driving position.

Fig.13

Removing the screw strip

When removing the screw strip at or before using up the

screws, pull it out in the direction of the arrow.

Fig.14

If you set the reverse lever as shown in the figure, you

can pull out the screw strip in the reverse direction of the

arrow.

Fig.15

Pulling away the screw strip

Fig.16

While operating the tool with the screw strip, the used

strip comes out. as shown in the figure.

Hook a hole in the strip on the protrusion (A ) and then

pull away the used strip that has come out in the direction

of arrow.

Extension handle (optional accessory)

Fig.17

Use of extension handle allows you to drive screws into

floors while standing.

OPERATION

Driving operation

Fig.18

Switch on the tool by pressing the switch trigger and at

the same time pushing the lock button. Hold the tool

squarely against the workpiece and apply forward

pressure to the tool. The screw will be automatically

carried to the driving position and driven into the

workpiece.

NOTE:

• Do not fire the tool without screws. This will

damage the workpiece.

• Do not apply oil or grease on the sliding surface of

the feeder box.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

Replacing carbon brushes

Fig.19

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

Fig.20

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita 6841R Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info