Handleiding Makita 5704rk (pagina 7 van 19) (Nederlands, Duits, Engels, Frans, Italiaans, Pools, Deens, Zweeds, Noors)

382502

Verklein

Vergroot

Pagina terug

1/19

Pagina verder

26. Wear a dust mask and hearing protection when

use the tool.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

OPERATING INSTRUCTIONS

Removing or installing saw blade

The following blade can be used with this tool.

The thickness of the riving knife is 1.8 mm.

CAUTION:

• Do not use saw blades which do not comply with the

characteristics specified in these instructions.

• Do not use saw blades the disc of which is thicker or

the set of which is smaller than the thickness of the riv-

ing knife.

To remove the saw blade, depress the shaft lock fully to

prevent shaft rotation, then use the hex wrench to loosen

the hex socket head bolt. (Fig. 8)

Now remove the outer flange, raise the safety cover as

much as possible, and remove the saw blade. (Fig. 9)

Install the saw blade using the reverse of the removal

procedure. Install the inner flange, saw blade, outer

flange and hex socket head bolt, in that order. Be sure to

secure the hex socket head bolt tightly with the shaft lock

fully depressed. (Fig. 10)

CAUTION:

• Make sure that the blade teeth point forward in the

same direction as the tool rotation (the arrow on the

blade should point in the same direction as the arrow

on the tool).

• The inner flange has a 30 mm diameter on one side

and a 20 mm diameter on the other. The side with 20

mm diameter is marked by “20”. Use the correct side

for the hole diameter of the blade you intend to use.

Mounting the blade on the wrong side can result in dan-

gerous vibration.

• Use only the Makita hex wrench to remove or install the

blade.

Riving knife adjustment (Fig. 11)

Use the hex wrench to loosen the hex socket head bolt

for the riving knife adjustment, then raise the safety

cover. Move the riving knife up or down over the two pro-

truberances for settings indicated in the illustration, so as

to obtain the proper clearance between the riving knife

and saw blade.

CAUTION:

Ensure that the riving knife is adjusted such that:

The distance between the riving knife and the toothed rim

of the saw blade is not more than 5 mm. The toothed rim

does not extend more than 5 mm beyond the lower edge

of the riving knife.

Adjusting depth of cut (Fig. 12)

Loosen the lever on the depth guide and move the base

up or down. At a desired depth of cut, secure the base by

tightening the lever.

CAUTION:

• Use a shallow depth of cut when cutting thin workpiece

for cleaner, safer cuts.

• After adjusting the depth of cut, always tighten the lever

securely.

Adjusting for bevel cuts (Fig. 13)

Loosen the thumb screws in front and back, and tilt the

tool to the desired angle for bevel cuts (0° – 45°). Secure

the thumb screws tightly in front and back after making

the adjustment.

Sighting (Fig. 14)

For straight cuts, align the right notch on the front of the

base with your cutting line on the workpiece.

For 45° bevel cuts, align the left notch with it.

Switch action (Fig. 15)

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop.

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

Operation (Fig. 16)

Hold the tool firmly. Set the base plate on the workpiece

to be cut without the blade making any contact. Then turn

the tool on and wait until the blade attains full speed.

Now simply move the tool forward over the workpiece

surface, keeping it flat and advancing smoothly until the

sawing is completed. To get clean cuts, keep your sawing

line straight and your speed of advance uniform.

CAUTION:

• The riving knife should always be used except when

plunging in the middle of the workpiece.

• Do not stop the saw blade by lateral pressure on the

disc.

Guide rule (Fig. 17)

The handy guide rule allows you to do extra-accurate

straight cuts. Simply slide the guide rule up snugly

against the side of the workpiece and secure it in position

with the bolt on the front of the base. It also makes

repeated cuts of uniform width possible.

Joint assembly (Fig. 18 & 19)

(for connecting a vacuum cleaner)

When you wish to perform clean cutting operation, con-

nect a vacuum cleaner to your tool. Install the joint on the

tool using the screw. Then connect a hose of vacuum

cleaner to the joint.

Max.

dia.

Min.

dia.

Hole

dia.

Blade

thickness

Kerf

190 mm 170 mm

20 mm

30 mm

less than

1.7 mm

than

1.9 mm

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita 5704rk Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info