448194
6
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
6
ENGLISH
Explanation of general view
1 Dust box
2 Screw
3 Hex wrench
4 Shaft lock
5 Tighten
6 Loosen
7 Hex socket head bolt
8 Outer flange
9 Diamond wheel
10 Inner flange
11 Lever
12 Bevel scale plate
13 Knob
14 Base
15 Adjusting screw
16 Triangular rule
17 Notch
18 For 45° bevel cuts
19 For straight cuts
20 Switch trigger
21 Lock-off button
22 Rear handle
23 Front grip
24 Guide rule
25 Dust cap
26 Rubber cap
27 Limit mark
28 Brush holder cap
29 Screwdriver
SPECIFICATIONS
Model 4157KB
Wheel diameter ...................................................180 mm
Max. cutting capacities
At 90° ................................................................. 58 mm
At 45° ................................................................. 29 mm
No load speed (min
–1
) ............................................ 5,800
Overall length ..................................................... 354 mm
Net weight ............................................................. 5.5 kg
Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220V and 250V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.31 Ohms it can be presumed that
there will be no negative effects. The mains socket used
for this device must be protected with a fuse or protective
circuit breaker having slow tripping characteristics.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
ENB051-1
1. Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
2. Use only flanges specified for this tool.
3. Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt. Dam-
age to these parts could result in wheel break-
age.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Make sure the wheel is not contacting the work-
piece before the switch is turned on.
7. Wait until the wheel attains full speed before cut-
ting.
8. Stop operation immediately if you notice any-
thing abnormal.
9. Do not attempt to lock the trigger in the “ON”
position.
10. Never attempt to cut with the tool held upside
down in a vise. This can lead to serious acci-
dents, because it is extremely dangerous.
(Fig. 1)
11. Before setting the tool down after completing a
cut, be sure that the wheel has come to a com-
plete stop.
12. Do not stop the wheel by lateral pressure on the
disc.
13. The tool must be used only for dry cutting. Do
not use water.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Removing or installing diamond wheel
(Fig. 2, 3 & 4)
CAUTION:
Always be sure that the tool is switched off and
unplugged before removing or installing the wheel.
Use a screwdriver to loosen the two screws which secure
the dust box. Then remove the dust box from the tool.
After removing the dust box, press the shaft lock so that
the diamond wheel cannot revolve and use the hex
wrench to loosen the hex socket head bolt counterclock-
wise. Then remove the hex socket head bolt, outer flange
and the diamond wheel. To install the diamond wheel, fol-
low the removal procedure in reverse.
BE SURE TO TIGHTEN THE HEX SOCKET HEAD
BOLT SECURELY.
CAUTION:
Make sure that the arrow on the wheel should point in
the same direction as the arrow on the tool.
Use only the Makita hex wrench to install or remove the
wheel.
Adjusting depth of cut (Fig. 5)
Loosen the lever on the depth guide and move the base
up or down. At the desired depth of cut, secure the base
by tightening the lever.
Bevel cutting (Fig. 6)
Loosen the knob on the bevel scale plate on the front of
the base. Set for the desired angle (0 – 45°) by tilting
accordingly, then tighten the knob securely.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita 4157 KB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita 4157 KB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info