Handleiding Makita 3709 (pagina 6 van 52) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

690941

Verklein

Vergroot

Pagina terug

1/52

Pagina verder

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing trimmer bit (Fig. 3)

CAUTION:

• Use only the wrenches provided with the tool.

Insert the bit all the way into the collet cone and tighten

the collet nut securely with the two wrenches.

To remove the bit, follow the installation procedure in

reverse.

OPERATION

Set the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the

bit attains full speed. Move the tool forward over the workpiece surface, keeping the tool base flush and advancing

smoothly until the cutting is complete.

When doing edge cutting, the workpiece surface should be on the left side of the bit in the feed direction. (Fig. 4)

NOTE:

• Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor. Moving the tool for-

ward too slowly may burn and mar the cut. The proper feed rate will depend on the bit size, the kind of workpiece and

depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample cut on a piece of

scrap lumber. This will show exactly how the cut will look as well as enable you to check dimensions.

• When using the trimmer shoe, the straight guide or the trimmer guide, be sure to keep it on the right side in the feed

direction. This will help to keep it flush with the side of the workpiece. (Fig. 5)

CAUTION:

• Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should

not be more than 3 mm at a pass when cutting grooves. When you wish to cut grooves more than 3 mm deep, make

several passes with progressively deeper bit settings.

Templet guide

The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns.

(Fig. 6)

Remove the chip deflector.

Loosen the screws and remove the base protector. Place the templet guide on the base and replace the base protec-

tor. Then secure the base protector by tightening the screws. (Fig. 7)

Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide sliding

along the side of the templet. (Fig. 8)

NOTE:

• The workpiece will be cut a slightly different size from the templet. Allow for the distance (X) between the router bit

and the outside of the templet guide. The distance (X) can be calculated by using the following equation:

Straight guide (Accessory)

The straight guide is effectively used for straight cuts

when chamfering or grooving. (Fig. 9)

Attach the guide plate to the straight guide with the bolt

and the wing nut. (Fig. 10)

Remove the chip deflector.

Attach the straight guide with the clamp screw (A).

Loosen the wing nut on the straight guide and adjust the

distance between the bit and the straight guide. At the

desired distance, tighten the wing nut securely.

When cutting, move the tool with the straight guide flush

with the side of the workpiece. (Fig. 11)

If the distance (A) between the side of the workpiece and

the cutting position is too wide for the straight guide, or if

the side of the workpiece is not straight, the straight

guide cannot be used. In this case, firmly clamp a

straight board to the workpiece and use it as a guide

against the trimmer base. Feed the tool in the direction of

the arrow. (Fig. 12)

Circular work

Circular work may be accomplished if you assemble the

straight guide and guide plate as shown in Fig. 13 or 14.

Min. and max. radius of circles to be cut (distance

between the centre of circle and the centre of bit) are as

follows:

Min.: 70 mm

Max.: 221 mm

Fig. 13 for cutting circles between 70 mm and 121 mm in

radius.

Fig. 14 for cutting circles between 121 mm and 221 mm

in radius.

NOTE:

• Circles between 172 mm and 186 mm in radius cannot

be cut using this guide.

Distance (X) =

outside diameter of the templet guide – router bit diameter

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Makita 3709 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info