448181
10
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
10
Symbols
The following show the symbols used for the tool. Be sure
that you understand their meaning before use.
............. Read instruction manual.
............. DOUBLE INSULATION
............... Wear safety glasses.
........... Do not place hand or fingers close to the
blade.
Intended use
The tool is intended for cutting in wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
ADDITIONAL SAFETY RULES
FOR TOOL
SAVE THESE INSTRUCTIONS.
1. Wear eye protection.
2. Don't use the tool in presence of flammable liq-
uids or gases.
3. NEVER use the tool with an abrasive cut-off wheel
installed.
4. Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
5. Use only saw blades recommended by the manu-
facturer and which conform to EN847-1, and
observe that the riving knife must not be thicker
than the width of the cut by the saw blade and not
thinner than the body of the blade.
6. Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive cut-off wheels may cause an injury.
7. Select the correct saw blade for the material to be
cut.
8. Do not use saw blades manufactured from high
speed steel.
9. To reduce the emitted noise, always be sure that
the blade is sharp and clean.
10. Use correctly sharpened saw blades. Observe the
maximum speed marked on the saw blade.
11. Clean the spindle, flanges (especially the install-
ing surface) and hex nut before installing the
blade. Poor installation may cause vibration/wob-
bling or slippage of the blade.
12. Use saw-blade guard and riving knife for every
operation for which it can be used, including all
through sawing operations. Always install the
blade guard following the instructions out-lined in
this manual. Through sawing operations are those
in which the blade cuts completely through the
workpiece as in ripping or cross cutting. NEVER
use the tool with a faulty blade guard or secure the
blade guard with a rope, string, etc. Any irregular
operation of the blade guard should be corrected
immediately.
13. Immediately reattach the guard and riving knife
after completing an operation which requires
removal of the guard.
14. Do not cut metals such as nails and screws.
Inspect for and remove all nails, screws and other
foreign matter from the workpiece before opera-
tion.
15. Remove wrenches, cut-off pieces, etc. from the
table before the switch is turned on.
16. NEVER wear gloves during operation.
17. Keep hands out of the line of the saw blade.
18. NEVER stand or permit anyone else to stand in
line with the path of the saw blade.
19. Make sure the blade is not contacting the riving
knife or workpiece before the switch is turned on.
20. Before using the tool on an actual workpiece, let it
run for a while. Watch for vibration or wobbling
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Makita-2704

Zoeken resetten

  • De aan/uit knop op mijn Makita 2704x tafelzaag blokkeert.
    Na wat zoek werk lees ik over een Nulspanningsbeveiliging.
    Echter lees ik nergens hoe ik deze ongedaan kan maken.
    Wie weet hoe deze beveiliging ongedaan gemaakt kan worden? Gesteld op 7-11-2016 om 20:17

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita 2704 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita 2704 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info