448175
7
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
7
8. Remove nails and clean the workpiece before
cutting. Nail, sand or foreign matter can cause
blade damage.
9. Do not remove chips from the chip chute when
the motor is running. Clean out chips after the
blades come to a complete stop. Always use a
stick etc. when cleaning them out.
10. Do not leave the tool running.
11. Do not abuse cord. Never yank cord to discon-
nect it from receptacle. Keep cord away from
heat, oil water and sharp edges.
12. The tool should only be used for wood and simi-
lar materials.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
INSTALLATION
Movement and transport of thicknesser (Fig. 1)
CAUTION:
Watch your step when moving the tool.
Fold the sub-tables. Grasp the carrying handles when
moving the tool.
When transporting it by vehicle, secure with a rope or
other substantial means to prevent tipping or movement.
Positioning the thicknesser (Fig. 2)
Locate the tool in a well lit and level place where you can
maintain good footing and balance. Bolt/screw it to the
workbench or stand (optional accessory) using the bolt
holes provided in the base.
FUNCTIONAL DESCRIPTION
CAUTION:
Always be sure that the tool is switched off and unplugged
before adjusting or checking function on the tool.
Switch action (Fig. 3)
CAUTION:
Before plugging in the tool, always be sure that the tool
is switched off. The pilot lamp lights up when the tool is
plugged into the power source.
To start the tool, press the ON (I) button. To stop it, press
the OFF (O) button.
Dimensional adjustment (Fig. 4)
Lower the main frame by turning the crank handle coun-
terclockwise until the indicator plate points to the scale
graduation indicating the desired finished dimension.
One full turn of the crank handle moves the main frame
2 mm up or down. The scale has inch graduations on its
right side and metric graduations on its left side.
Adjusting depth of cut
The maximum depth of cut differs depending upon the
width of workpiece being cut. Refer to the table. When
you need to remove more than the amount specified in
the table, set the depth of cut shallower than the amount
and make two or more passes.
To adjust the depth of cut, proceed as follows.
Insert the workpiece flat on the table top. Lower the main
frame by turning the crank handle counterclockwise. The
depth gauge will rise and the amount of gauge rise indi-
cates the depth of cut. (Fig. 5)
CAUTION:
Always lower the main frame when aligning the indica-
tor plate with the graduation indicating the desired fin-
ished dimension. If you raise the main frame into the
desired finished dimension, additional play in the screw
may result. This may cause an undesired finished
dimension.
Always place the workpiece flat on the table top when
predetermining the depth of cut. Otherwise, the prede-
termined depth of cut will differ from actual depth of cut.
Depth adjusting gauge (Fig. 6)
Use the depth adjusting gauge when you need to prede-
termine the depth of cut more accurately. To do so, pro-
ceed as follows.
1. First, plane the workpiece at the predetermined
depth of cut. Measure the thickness of the planed
piece to know how much more stock you need to
remove.
2. Turn the depth adjusting gauge on the crank handle
until the 0 graduation is aligned with the groove on
the tool.
3. Now turn the crank handle counterclockwise until
the graduation for the desired depth of cut is aligned
with the groove on the tool.
4. When you need to remove more than the amount
specified in the table mentioned in the “Adjusting
depth of cut” section, set the depth of cut shallower
than the amount and make two or more passes.
Stopper (Fig. 7)
Use the stopper when you need to plane many work-
pieces to the same thickness. To do so, proceed as fol-
lows.
1. Turn the crank handle until the indicator plate points
to the scale graduation indicating the desired fin-
ished dimension.
2. Depress the stopper button and lower the stopper
until it just contacts the table top.
3. If you need fine adjustment of the stopper, turn the
stopper knob.
CAUTION:
When the stopper is not in use, always raise it to the
topmost position. Never force the crank handle when
the stopper is in contact with the table top. This may
cause tool damage.
Width of workpiece
being cut
Maximum depth of cut
Less than 150 mm 3.0 mm
150 mm – 240 mm 1.5 mm
240 mm – 304 mm 1.0 mm
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita 2012 NB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita 2012 NB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens als bijlage per email.

De handleiding is 1,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Makita 2012 NB

Makita 2012 NB Gebruiksaanwijzing - Nederlands, English - 17 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info