534675
28
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
28
TROUBLESHOOTING
Can’t load filament?
If you are having problems loading filament
into one of the extruders, perform the
following steps:
1. Go to the LCD panel and select Utilities
> Filament Options > Unload. This option
heats the extruders.
2. Set the extruder arm to the open position.
3. Make a fresh cut at the end of the
filament. It is important that the filament
have nobends in it. If it does, cut o the
bentsection of filament.
4. Insert the filament into the hole at the top
of the extruder. Keep pushing it in until you
start to see plastic come out of the nozzle.
5. When the filament is successfully
loaded, set the extruder lever arm to the
closed position.
If filament still doesn’t emerge from the
nozzle, remove the filament from the top of
the extruder and check for a bend at the end
of the filament. If the filament is bent, it is
possible that the filament is slipping under
the extruder bearing instead of entering the
extruder heater. Remove the extruder fan
and assembly using the instructions in the
section Disassembling an Extruder. This
will allow you to watch the filament travel
through the extruder and determine where
the filament is getting stuck.
It is also possible that you are unable to load
filament because a broken piece of filament
remains inside of the extruder. Remove
the extruder fan and assembly using the
instructions in the section Disassembling
an Extruder and use a pair of pliers to
remove the broken end of filament.
Extruder arms open
Extruder arms closed
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MakerBot Replicator 2X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MakerBot Replicator 2X in de taal/talen: Engels als bijlage per email.

De handleiding is 7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info