Handleiding Magnat QUANTUM 1003 S (pagina 6 van 36) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Zweeds)

581673

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

Dear MAGNAT Customer,

Congratulations on your ﬁne new loudspeakers and thank you very much for choosing MAGNAT! You have made an excellent

choice. The high-quality speakers produced by MAGNAT are renowned all over the world.

Please study the instructions and information below carefully before using your new loudspeakers.

GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT QUANTUM 1000 S LOUDSPEAKERS

Warning: Only hi-ﬁ ampliﬁer loudspeaker outputs may be connected to the Quantum 1000 S loudspeaker terminal.

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent impairment of sound quality,

we recommend cables with cross-sections of at least 2.5 mm² for lengths up to 3 m and at least 4 mm² for lengths above 3 m.

Always turn off the ampliﬁer or receiver before connecting or disconnecting loudspeaker cables. Place the loudspeakers in their

planned positions and cut the cables to the right length. The cables for both channels should always be exactly the same length.

For good sound it is imperative that the cables must be connected in such a way that the speakers are “in phase”. This means

that the black negative terminals on the speakers (-) must be connected to the negative (-) terminals on the ampliﬁer, the red

positive (+) speaker terminals to the positive (+) ampliﬁer terminals. To make this easier one wire of most speaker cables is

marked with a coloured strip or a ridge in the insulation.

The Quantum 1000 S terminal is designed for 3 cord sets:

Connection via banana plugs (ﬁg. 1a)

Connection via clevis type ﬁttings (ﬁg. 1b)

Non-ready-made (ﬁg. 1c):

Strip 10 – 15 mm of insulation from the ends of non-ready-made cables. Twist the ends – this is much better than tinning them

with solder – insert them in the terminals and tighten the terminal screws ﬁrmly.

Before switching on the system double-check all your connections and make sure that the terminal screws are tight and that

there are no short circuits caused by stray wire ﬁlaments – this could cause serious damage to your ampliﬁer!

THE MAGNAT QUANTUM 1000 S LOUDSPEAKERS IN STEREO MODE

In the ideal conﬁguration the speakers and the listening position should form an equilateral triangle. When the left and right

speakers are the same distance from the listening position their sound arrives at the same time, resulting in a harmonious,

natural music reproduction. (Fig. 2)

There should be a clear line of sight between the loudspeakers and the listening position. Any sound-absorbing or reﬂecting

obstacles in the path will distort the sound. When you install the loudspeakers the following distances should be maintained:

at least 20 cm away from the rear wall and at least 30 cm from the side walls. This will prevent excessive emphasis of the bass

range.

MAGNAT QUANTUM 1000 S LOUDSPEAKERS AS A FRONT OR REAR LOUDSPEAKER

The front loudspeakers are positioned at ear height on the left and right as equidistant from the television as possible. The rear

loudspeakers are placed at ear height or a little above on the left and right besides or better behind the listening position.

therwise all the recommendations made in the previous chapter also apply.

MAGNAT QUANTUM CENTER 1000 S

The Quantum Center 1000 S loudspeaker visually and acoustically ideally matches the other Quantum 1000 S models. The

loudspeaker is placed immediately on or under the television set. Otherwise please adhere to the general recommendations

outlined in the previous chapters.

SPIKES (QUANTUM 1009 S)

You should use the supplied spikes. The spikes are height-adjustable and possess a counter nut.

Any irregularities in the ﬂoor may be offset and a ﬁrm stand may be achieved with the spikes. They also decouple the

loudspeakers from the base so that any undesirable resonance is avoided.

The spikes must be screwed into the threaded sleeves at the bottom of the box when the hard rubber feet have been removed.

In order to prevent the ﬂoor from being damaged, you should get help from someone to tilt the box slightly when ﬁtting the

spikes.

First, screw in two spikes next to each other and – before setting the box down – put the corresponding washers (rubber facing

down) in place. Then attach the two opposite spikes and lower accordingly.

Then align the box vertically and counter the spikes.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Magnat QUANTUM 1003 S Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info