Handleiding MTD Zero Turn Serie RZT-S (pagina 13 van 18) (Engels)

629100

Verklein

Vergroot

Pagina terug

1/18

Pagina verder

English Operating Manual

Note

The number of cutter deck wheels

varies depending on the model:

– 107 cm cutter deck:

2 wheels at front

– 117 cm cutter deck:

2 wheels at front and 2 wheels

at back

– 127 cm/137 cm cutter deck:

2 wheels at front and 2 rollers

(rear rollers) at back

Setting the rear rollers

(depending on model)

The rear rollers can be attached

in two positions.

Fig. 15

„High“ position (upper hole):

Standard position – the grass is not

rolled or only minimally.

„Low“ position (lower hole):

Roll position – the grass is also

rolled after cutting.

 Remove safety split pin (1) from

the right side.

 Pull out axle (2) to the left.

 Insert axle into the required hole

(High/Low). When inserting the

rollers (3), push back onto the

axle.

 Align axle (2) with the groove and

push through the right holder.

Re-insert safety split pin (1).

Note

Always fit rear roller on both sides

in the same position (High/Low).

Starting the engine

 Sit on the driver’s seat.

 Switch off the cutter deck:

Switch off PTO and raise the

cutter deck.

 Push the brake pedal down fully

or lock the parking brake.

 Do not actuate accelerator

pedals (= neutral position,

N position).

 Move throttle to .

 If the engine is cold, pull out the

choke or set the throttle to .

 Turn the ignition key to until

the engine is running (start

attempt max. 5 seconds, wait

10 seconds before the next

attempt). When the engine is

running, set the ignition key to

 Slowly push back the choke.

 Return the accelerator lever until

the engine runs smoothly.

Stopping the engine

 Move the throttle to the middle

position.



Leave the engine running for

approx. 20 seconds.

 Set ignition key to .

 Remove the ignition key.

 Engage the locking brake before

leaving the appliance.

Driving

Danger

Abrupt starting, sudden stopping,

and driving at an excessively

high speed increases the risk of

accidents and may damage the

unit.

Never set/adjust the driver’s seat

while the unit is moving.

Note

Be particularly careful when

reversing. Never change the

direction of travel without first

bringing the unit to a standstill.

 Start the engine as indicated.

 Release the parking brake. Press

down fully the brake pedal, and

release it.

 Slowly engage the drive pedal

until you have reached the speed

you want.

Note

The forwards and reverse accele-

rator pedal must not be used if the

brake pedal is depressed. This may

damage the gears.

Stopping the unit

 Release the accelerator.

 Depress brake pedal until the

unit stops.

Mowing

Note

– In normal mowing mode

(see Operation,

ignition lock):

Before reversing the machine,

switch off and raise the cutter

deck.

– In reverse mowing mode

(see Operation,

ignition lock): Exercise extreme

caution when reverse mowing

and do not activate unless

absolutely necessary.

– Do not change direction when

the appliance is coasting or

driving.

 Start the engine as indicated.

 To ensure adequate power

output, move the throttle to .

 Switch on the cutter deck.

 Lower the cutter deck.

 Release the parking brake.

Press down fully the brake pedal,

and release it.

 Slowly depress the forward drive

pedal for forward direction of

travel and speed. The appliance

starts moving.

Information on PTO switch

When the safety lock system has

automatically switched OFF the

appliance (e.g. when reversing with

activated cutters), first switch ON

and then OFF the PTO switch to

release the lock on the clutch.

General information

When adjusting the cutting height

and driving speed, ensure that the

machine is not overloaded.

Depending on the length, type,

and dampness of the grass it may

become necessary to adjust the

cutting height and appliance speed

for the optimum grass catcher

performance.

If blockages occur, reduce the

driving speed and increase the

cutting height.

The best way to mow

Cut the first two rounds so the cut

grass is thrown out sideways into

the middle.

 Never allow the grass to grow too

long

 Never cut the grass too low.

 Drive in a straight line.

 Never mow at high speed,

particularly when a mulching

kit or grass catcher is installed.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

MTD Zero Turn Serie RZT-S Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van MTD Zero Turn Serie RZT-S

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info