Handleiding MTD CubCadet serie 6000 (pagina 14 van 25) (Engels)

507839

Verklein

Vergroot

Pagina terug

1/25

Pagina verder

User manual English

Preparing for operation

 Park the tractor on an even, solid

surface.

 Lock the parking brake.

 Conduct all work with the engine

switched off.

 Remove the ignition key.

Set the driver seat

The driver's seat is adjustable in

terms of height, longitude and

hardness.

Setting the seat longitudinally

Fig. 14 a

 Take your place on the driver

seat.

 Pull the lever (1) outwards and

bring the seat into the desired

position.

 Release the lever and engage the

seat by gently moving it forwards

and backwards.

Adjusting the height

Fig. 14 a

 Setting the seat higher.

Turn the knob (2) in a clockwise

direction.

 Setting the seat lower.

Turn the knob (2) in a clockwise

direction.

Setting the driver seat hardness

Figure 14 b

 Swivel the lever (3) forwards such

that when turning, the lever does

not hit the seat.

 Setting the seat harder:

Turn the lever in a clockwise

direction.

 Setting the seat softer:

Turn the lever in an anti-clockwise

direction.

 Swivel the lever back.

Setting the seat belt

Fig. 15

Note

If the seat belt is too long or too short

to be set by pulling on the upper lying

belt, the position of the readjustment

clip should be changed. To do this,

hold the readjustment clip tightly and

pull the under lying belt through the

clip.

Move the clip towards the anchor

point of the seat to shorten the belt

or to make it longer.

Set the final length of the belt with the

readjustment clip, the latch and the

upper lying belt into the

right

half

of the belt.



In order to lengthen the belt, hold

the readjustment clip (a) ends tightly

and tip the side of the clip upwards

towards the latch.



While holding the clip, pull the

upper lying belt through clip

towards the latch (b).



Hold the belt and pull the latch to

the

left

in order to remove the slack

in the upper lying belt between the

readjustment and the latch.



To shorten the belt, tip the other

side of the clip upwards, pull the

free end of the belt to the

êáÖÜí

and

pull the latch to the

äÉÑí

in order to

remove the slack.

Filling and checking the oil

level

Note

The engine should already have

been filled with oil at the factory –

please check and where necessary,

top it up.

 Fill with ‘diesel’.

 Fill the fuel tank to a maximum of

2.5 cm below the lower edge of

the filler neck.

 Turn the fuel tank stopper tight.

 Check the oil level.

The oil level must lie between the

‘full/max’ and ‘add/min’ mark

(see also the engine manual).

Check the cooling water fill

level

Fig. 16

The cooling water fill level must be

located between the MIN and MAX

marker on the adjustment container.

Top up where necessary (see

section “Servicing”).

Check the tyre pressure

Note

For manufacturing reasons, the tyre

pressure can be higher than

necessary.

 Check the tyre pressure. Correct

where necessary (see section

“Servicing”).

–front 0.7 bar

– rear 1.0 bar

Starting the engine

 Sit in the driver seat.

 Set the gear lever to the neutral

setting N.

 Switch off the PTO-switch.

 Move throttle to maximum .

 Push the brake pedal down fully

or lock the parking brake.

 Turn the ignition key to /I.

Diesel motors have to be preheated

before starting the engine. Reaching

the required temperature for starting

the engine is indicated by the glow

plug pilot light going out.

Note

A warm engine does not need to be

preheated.

After the glow plug pilot light (A) has

gone out:

 Turn the ignition key to until

the engine runs. (max.10 sec. for

the first starting attempt). Wait for

one minute before the next

attempt, however at the same

time return the key to the /0

position.

When the engine is running:

 Turn the key back to /I.

 Slowly turn the throttle in the

direction /idle. Let the engine

run warm for approx. 3–5

minutes.

Note

Do not operate the engine when fully

loaded until it is has heated up.

For temperatures under 0 °C:

– Observe the correct viscosity of the

engine oil (see table in section “Ser-

vicing” and/or the engine manual).

– Set the throttle lever into

position .

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

MTD CubCadet serie 6000 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van MTD CubCadet serie 6000

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info