672424
8
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
Operating manual English
5
Before switching on the engine,
carry the unit at least 10 m away
from the filling station. While filling
the tank or using the unit, do not
smoke and keep sparks and
naked flames out of the area.
Replace damaged exhausts, fuel
tanks, or filler caps.
Operating the unit
Never start the unit and never
leave it running in a closed room
or building. The inhalation of
exhaust gases may be fatal.
Use the unit outdoors only.
Wear eye and ear protection when
using the unit. If working in a dusty
environment, wear a face or dust
mask. A long-sleeved shirt is
recommended.
Wear thick, long trousers , boots
and gloves. Do not wear loose
clothing, jewellery, short trousers,
sandals and do not walk barefoot.
Pin your hair above your shoulders.
If required, wear a hair net.
The cutting attachment cover must
always be attached when you use
the unit as a lawn trimmer. Both
trim lines must be pulled out and
the correct line must be installed.
The trim line must not be pulled
out over the end of the cover.
The unit has a clutch. The cutting
attachment stops when the unit is
running at no load. If it does not
stop, have the unit adjusted by
a mechanic at your authorised
dealer.
Before switching on the unit,
ensure that the line spool/cutting
blade cannot strike an object.
Adjust the handle bar to your
height so that the you have
the unit under control.
Operate the unit in daylight or
adequate artificial lighting only.
Avoid starting the unit
unintentionally. Be ready to operate
the unit when you pull the starter
rope. User and unit must be in
a stable position when the unit
is started. Follow the Start/Stop
instructions.
Use this unit for its designated
purpose only.
Do not stretch too far over the unit.
Always have a secure footing and
keep your balance.
When operating the unit, always
hold the unit firmly with both hands.
Always hold both sides of the
handle bar firmly.
When operating the unit, always
wear the shoulder belt.
Do not use the unit in adverse
weather conditions, e.g. if there is
a probability of rain or a storm.
Never change the engine settings
preset at the factory.
Keep away from naked flames,
avoid creating sparks and do not
smoke.
Never operate the unit with
a defective ignition switch.
Keep your hands, face and feet
away from all moving parts. Do
not touch the cutting attachment
while it is rotating and do not
attempt to stop it.
Do not touch the engine or muffler.
These parts become very hot
while the unit is being used. They
remain hot for a short time even
when the unit is switched off.
Do not let the engine run quicker
than required for cutting or
trimming of lawn edges. Do not
run the engine at high speed when
it is not cutting.
Always switch off the engine if you
cannot start cutting immediately
or if you are moving from one
place to another.
If unusual vibrations occur, switch
off the engine immediately. Check
the unit for damage. If the unit is
damaged, contact a specialist
company.
If you strike or ensnare a foreign
object, immediately switch off the
engine and check whether the unit
has been damaged. Never use the
unit with loose or damaged parts.
Before removing blockages or
performing other work on the unit,
switch off the engine and remove
the spark-plug terminal.
Stop and switch the engine off
before performing maintenance or
repairs or before changing cutting
attachments. Also pull out the
spark-plug terminal.
Use only original spare parts
for repairs. These parts can be
purchased from your authorised
dealer.
Never use parts, accessories or
attachments which are not
authorised for this unit. Otherwise,
the user may be seriously injured
and the unit damaged. In addition,
your warranty may be deemed
null and void.
Keep the unit clean and ensure
that there are no plants or other
objects caught between the cutting
attachment and guard.
To reduce the risk of fire, please
replace damaged mufflers and
spark extinguishers and remove
grass, leaves, excess lubricants
and layers of soot from the engine
and muffler.
Have all repairs carried out by
a repair shop only.
Working with the cutting
blade (depending on model)
Before operating the unit, please
read all safety instructions carefully.
Always keep the handle bar
between the user and cutting
attachment.
NEVER cut material if the cutting
blade is 75 cm or higher above
ground level.
The unit may recoil if the rotating
blade strikes an object which
cannot be cut immediately.
Recoils may be strong enough to
throw the unit and/or user in any
direction and may cause the user
to lose control of the unit. Recoils
may occur without warning if the
blade gets caught, jams or locks.
This can easily happen in areas in
which the material to be cut is
difficult to see.
Never use the undergrowth blade
to cut undergrowth thicker than
12.7 mm. Otherwise, violent
recoils may occur.
When using the cutting blade,
the cutting attachment cover
must always be attached.
Do not attempt to touch or stop
the blade while it is rotating.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MTD 1043 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MTD 1043 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van MTD 1043

MTD 1043 Gebruiksaanwijzing - Nederlands - 16 pagina's

MTD 1043 Gebruiksaanwijzing - Deutsch - 16 pagina's

MTD 1043 Gebruiksaanwijzing - Français - 17 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info