568583
17
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
ENGLISH | VISTUS-VD
1717
‚ID-CODE‘). This makes it possible to activate the individual outdoor
stations in turn from one indoor unit in order to be able to monitor the
scope of the corresponding outdoor units. The switch is activated on the
indoor station with the ‘monitor’ button.
ID1 = Switch 1 ‘on’, Switch 2 ‘on’
ID2 = Switch 1 ‘on’, Switch 2 ‘off’
ID3 = Switch 1 ‘off, Switch 2 ‘on’
Note: ID 4 is not available for the outdoor station. It is reserved for the
outdoor camera. If several outdoor stations are used in parallel then
only one outdoor station can be connected to the external camera.
Door opener time
The DIP switch (Figure A, ‚Door opener time‘) is used to set how long
the door opener should be activated for. The possible settings are 1
second or 5 seconds. 5 seconds is the factory setting and works for
most standard door openers.
Switch ‘off’ corresponds to an opening time of 1 second.
Switch ‘on’ corresponds to an opening time of 5 seconds.
POSSIBLE SETTINGS ON THE INDOOR STATION
The following settings are possible on the indoor station to adjust the
system to your personal circumstances:
Ring tone volume (3.5“ and 7“ monitor)
The potentiometer (Figure B and C ‘Bell Volume‘’) is used to set the
ring/volume on the indoor station. For full volume turn the potenti-
ometer carefully in a clockwise connection until it stops. Turning the
potentiometer in an anti-clockwise direction reduces the volume.
Deactivate ring tone/melody (e.g. during the night)
The ring tone/melody can be deactivated, e.g. in order to prevent
disturbance during the night. Either press the mute button on the
indoor unit once briefly. The LED below the mute button lights up red
as a reminder that the melody is deactivated. To activate the melody
again press the mute button again briefly. When the red LED goes out
the melody has been re-activated.
The optical signal (surround light on the talk and door opener button)
remains active, even then the ring tone/melody is deactivated and still
rings. The red LED flashes if the bell is rung while the mute is activated.
NOTE: If the VTX-BELL module is used then this will also be deactivated
in the silent mode, i.e. the connected receivers will not give a
signal either.
IMPORTANT: The monitor on the indoor station needs to be
activated for the following settings (e.g. by pressing the screen button).
Otherwise it is not possible to set the talk/volume, brightness, contrast,
colour saturation and melody.
Speaking volume (3.5“ and 7“ monitor)
The two side buttons (B/C. 12 and 13) can be used to set the speaking
volume in several steps. Button 12 is used to increase the volume and
button 13 to reduce it.
Brightness (3.5“ monitor)
The
button (B.8) is used to set the brightness on the monitor. The
button is pressed multiple times to increase the brightness. Once the
highest level of brightness has been reached another press will switch it
to the lowest level of brightness.
Contrast (3.5“ monitor)
The button (B.9) is used to set the contrast on the monitor. The
button is pressed multiple times to increase the contrast. Once the
highest level of contrast has been reached another press will switch it to
the lowest level of contrast.
Colour saturation (3.5“ Monitor)
The button (B.10) is used to set the colour saturation on the monitor.
The button is pressed multiple times to increase the saturation. Once
the highest level of saturation has been reached another press will
switch it to the lowest level of saturation.
Brightness (7“ monitor)
Press the button (C.8) on the indoor station once and the OSD will
display ‘Bright’. You can now increase the brightness using button (C.9)
and reduce it using button (C.10).
Contrast (7“ monitor)
Press the button (C.8) on the indoor station twice and the OSD will
display ‘Contrast’. You can now increase the contrast using button (C.9)
and reduce it using button (C.10).
Colour saturation (7“ monitor)
Press the button (C.8) on the indoor station three times and the
OSD will display ‘Colour’. You can now increase the colour saturation
using button (C.9) and reduce it using button (C.10).
Melody selection (3.5“ and 7“ monitor)
The next melody is played every time you press the button
(B/C.11). The last melody to be played is automatically stored.
VISTUS VD-600_I-Manual_210x240_Fin9.indd 17 10.06.13 15:52
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ME VD 607 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ME VD 607 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 3,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info