643410
69
Verklein
Vergroot
Pagina terug
1/74
Pagina verder
6-SICUREZZE E ALLARMI
67
11-PROBLEMS/CAUSES/SOLUTIONS
Technical Dept. - All rights reserved - Reproduction is prohibited
ATTENTION!
All repairs must only be carried out by a specialised technician, with the product switched o and the plug
disconnected.
If the product is NOT used as described in this manual, the manufacturer declines all liability for any damage caused
to persons and property.
All the necessary measures and/or precautions must be adopted when performing maintenance, cleaning and
repairs.
Do not tamper with the safety devices.
Do not remove the safety devices.
Connect the product to an ecient smoke expulsion system.
Verify that the room in which the appliance will be installed is adequately ventilated.
ANOMALY POSSIBLE CAUSES SOLUTIONS
Pellets are not being fed into the
combustion chamber.
The pellet hopper is empty. Fill the hopper with pellets.
Sawdust has blocked the feed screw. Empty the hopper and remove the sawdust
from the feed screw by hand.
Faulty gear motor. Replace the gear motor.
Faulty electronic board. Replace the circuit board.
The re goes out or the appliance
stops automatically.
The pellet hopper is empty. Fill the hopper with pellets.
The pellets are not fed. See the previous anomaly.
The pellet temperature safety probe has
been triggered.
Let the product cool down, restore the
thermostat until the problem is resolved
and switch the product back on. If the
problem persists contact Technical
Assistance.
The door is not closed properly or the
gaskets are worn.
Close the door and replace the gaskets
with original ones.
Unsuitable pellets. Change the type of pellets with those
recommended by the manufacturer.
Low pellet supply. Have the fuel ow rate checked by
Technical Assistance.
The combustion chamber is dirty. Clean the combustion chamber in
accordance with the installation guide.
Clogged outlet. Clean the smoke duct.
Faulty smoke extraction motor. Check the motor and replace it, if
necessary.
Water tank temperature too high. Check the circulation pump is working
properly and eventually replace the
component.
69

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

MCZ-Vivo-80-Pellet-Hydro

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MCZ Vivo 80 Pellet Hydro bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MCZ Vivo 80 Pellet Hydro in de taal/talen: Engels als bijlage per email.

De handleiding is 12,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van MCZ Vivo 80 Pellet Hydro

MCZ Vivo 80 Pellet Hydro Gebruiksaanwijzing en installatiehandleiding - Nederlands - 64 pagina's

MCZ Vivo 80 Pellet Hydro Gebruiksaanwijzing en installatiehandleiding - Français - 64 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info