643409
45
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
43
10-SAFETY DEVICES AND ALARMS
Technical Dept. - All rights reserved - Reproduction is prohibited
A10
The spark plug is faulty. Contact an authorised service centre to have the
component replaced.
A11
Pellet supply fault. Contact an authorised service centre to have the
component replaced.
A12
The remote control has been out of the product
reception range for over 3 hours (or the batteries
are at).
NOTE: the appliance does not enter the
shutdown phase due to an alarm only in such a
case, and continues to work in the mode set by
the remote control via the last command.
Move the remote control within the product reception
range (or change the batteries of the remote control if
they are at). The alarm alerts will disappear as soon
as the appliance receives a new signal from the remote
control. A simple way of forcing signal transmission to
the product is by pressing button 4 (which changes the
operating mode from manual to automatic and vice
versa).
A13
General fault in the electronic control unit. Contact an authorised service centre to have the
component replaced.
A14
Faulty air ow rate sensor. This alarm does not block the system and only a
warning screen is displayed. Contact an authorised
service centre to have the component replaced.
SEr
Routine maintenance alert. This ashing message upon start-up indicates that the
preset operating hours before maintenance is due have
elapsed and a qualied technician, recommended by
the manufacturer, must be contacted for maintenance
to be performed.
DELETING THE ALARM STATUS
Follow the procedure described below to restore normal product operation after an alarm has been triggered:
set selector D on the rear emergency panel to OFF for a few seconds until the 3 digit alarm identication code disappears. The red LED
stops ashing and the alarm buzzer is silenced by performing the steps below.
Set selector D back to the REMOTE position for product operation to be remote controlled.
Switch the remote control o and then on again if the product is to be switched on.
Only if alarm A12 is triggered (no communication between the remote control and the product), the appliance
remains on according to the last mode set and automatically exits the alarm mode when the rst signal is received
from the remote control.
45

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MCZ Vivo 80 Pellet COMFORT AIR bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MCZ Vivo 80 Pellet COMFORT AIR in de taal/talen: Engels als bijlage per email.

De handleiding is 4,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van MCZ Vivo 80 Pellet COMFORT AIR

MCZ Vivo 80 Pellet COMFORT AIR Gebruiksaanwijzing en installatiehandleiding - Français - 56 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info