Handleiding Lumag HGM-85055 (pagina 21 van 36) (Engels)

708397

Verklein

Vergroot

Pagina terug

1/36

Pagina verder

-15-

(GB)

VI.

Operating the Machine

The machine is intended for maintenance of irregularly mowed grass areas. The mulching machine disintegrates the

vegetation into small pieces that remain evenly distributed in place. Grass remains thus do not cumulate in one place an

d sere as

natural fertilizer.

2. Mulching Process

Mulching frequency: Perform mulching 3-4 times per year. First mulching should be performed at the beginning of the

vegetation season; last mulching should be performed at the end of the vegetation season. Other mulching depends on grass

growth conditions.

Mulching method: Use a single phase for mulching of grass up to 25 cm – adjust the knife height depending on grass

vegetation quality.

Grass exceeding 25 cm should be mulched in two phases, Fig. 10. Adjust the knife height to the higher position No. II, Fig.

4, for the first phase.

It is possible to lower the knife height to position No. I, Fig. 4, during the second phase.

2. Mowing Height Adjustment

Stubble height can be adjusted by rearranging the two soles (1) fitted to the mulching tunnel through bolt connections.

The stubble height can be adjusted in two position, the basic position No. I, and by readjusting soles in position No. II. Fig. 4.

Stubble height adjustment in position No. II.

Loosen the bolt with nut (2) in the front sole part, loosen and unscrew the bolt (3) in the rear sole part. Shift the rear sole part

so that the sole opening overlaps with opening No. II on the tunnel. Run the bolt (3) through both openings and the saddle

washer (4). Screw-in the self-locking nut from the inner tunnel side and tighten the connection. Then tighten the bolt with

self-locking nut (2) in the front sole part.

Perform the same procedures when rearranging the second sole. Both soles must be adjusted to the same height! Fig. 4.

Thus, the machine can be adjusted to a specific terrain.

3. Mulching Machine Drive

Adjust the accelerator control lever (3), Fig. 3, to the “START” position for a cold engine, to the “MAX” position for a warm

engine and start the engine. Observe instructions provided in the instructions for use of the engine throughout the operation.

The accelerator is located in the central section of the upper handlebar part.

During engine start-up, both clutch levers on the handlebars need to be released. Adjust max. engine revolutions by the

accelerator lever.

Grab the handlebar grip. Press the lever (2), Fig. 3, on the right handlebar side. Keep pressing the lever up to two travel thirds

very slowly in order for the mowing knife to be able to start turning and the engine not stopping. ♠Knife start-up is

accompanied by partial slipping of the vee-belt and the related effects (rattling, whistling). Upon start-up of the mowing

knife, press the lever completely toward the handle.

Engaging of the drive is performed by a lever (1), Fig. 3, on the left handlebar side. Press the lever to the handle and the

machine starts moving.

5. Stopping the Mulching Machine

Release the left lever and the machine stops. The mowing knife drive is shut down immediately upon release of the right

lever. The safety brake stops the mowing knife within a very short time. During turning or backward movement with the

machine it is not necessary to stop the mowing knife in order to prevent wasting of energy of the spinning mowing knife. The

engine is stopped by moving the accelerator lever (3), Fig. 3, to position “0”.

In case of a critical situation, immediately release both levers on the handlebar. The levers return to the zero position, the

drive and the mowing knife come to a halt.

VII.

Adjustment and Maintenance

1. Replacement of the Mowing Knife

Loosen and unscrew the knife bolt (1) with the washer (2), knife washer (3) and the disk washer (4) that fixes the

mulching knife (5) to the knife nave (6). Have the knife sharpened or exchange it. Perform assembly in reverse order of Fig.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Lumag HGM-85055 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info