756998
10
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
MARINE ELECTRONICS
One Touch To Choose Your World
COMPACT 7 Plus
Gray Levels Chartplotter with Internal GPS Receiver and Antenna
CODE: S3igLZ7m 1001c884/220305
EXCALIBUR 7 Speed
Gray Levels Chartplotter with External GPS Receiver and Smart Antenna
CODE: S3egLZ7m 1001c884/220305
COMPACT 7 Sun Color
Sunlight Readable Display Color Chartplotter with Internal GPS Receiver and Antenna
CODE: S3igLZ7c 1001c844/220305
EXCALIBUR 7 Speed Sun Color
Sunlight Readable Display Color Chartplotterwith External GPS Receiver and Smart Antenna
CODE: S3egLZ7c 1001c844/220305
USER MANUAL
Copyright 2005 LORENZ ELECTRONICS Italia.
All rights reserved. Printed in Italy. No part of this publication may be reproduced or distributed in any form or by any
means, or stored in a database or retrieval system, without prior written permission of the publisher.
4User Manual
Warning!
Electronic charts displayed by the chartplotter are believed to be accurate and reliable, but they are not
intended to replace official charts which should remain your main reference for all the matters related
to the execution of a safe navigation.
For this reason we would like to remind you that you are required to carry on board and use the
officially published and approved nautical charts.
Caution
Please read through this manual before the first operation. If you have any questions, please contact
the Company's customer service or your local dealer.
The chartplotter is not built water proof. Please give attention to avoid water intrusion into the
chartplotter. Water damage is not covered by the warranty.
Extensive exposure to heat may result in damage to the chartplotter.
Connection to the power source with reversed polarity will damage the chartplotter severely. This
damage is not covered by the warranty.
The chartplotter contains dangerous high voltage circuits which only experienced technicians MUST
handle.
The C-MAP C-CARD are available from your local dealer.
We will not be liable for errors contained herein, or for incidental or consequential damages in
connection with the performance or use of this material.
Exposure of display to UV rays may shorten life of the liquid crystals used in your plotter. This
limitation is due to the current technology of the LCD displays.
Avoid overheating which may cause loss of contrast and, in extreme cases, a darkening of the screen.
Problems which occur from overheating are reversible when temperature decreases.
Cleaning procedure for the plotter screen
Cleaning your plotter screen is a very important operation and must be done carefully. Since the
surface is covered by a antireflective coating, the procedure for cleaning all the surfaces can be per-
formed using the following procedure: You need a tissue or lens tissue and a cleaning spray containing
Isopropanol (a normal spray cleaner sold for the PC screen, for example PolaClear by Polaroid). Fold
the tissue or lens tissue into a triangular shape, moisten the tip and use the index finger behind a corner
to move the tissue across the surface, in overlapping side to side strokes. If the tissue is too wet, a
noticeable wet film will be left in its path and you will need to repeat the process. If too dry, the tissue
won’t glide easily, and may damage the surface.
5
User Manual
Table of Content
1 Introduction ........................................................................................... 11
1.1 CONVENTIONS ........................................................................................ 11
1.2 FEATURES ........................................................................................... 12
1.2.1 Specifications ................................................................................. 12
1.2.1.1 Main Characteristics .......................................................... 12
1.2.1.2 Phisical Characteristics ...................................................... 14
1.3 BASICS ........................................................................................... 15
2 Before You Begin ........................................................................................... 17
2.1 THE KEYBOARD ...................................................................................... 17
2.2 TURNING THE CHARTPLOTTER ON AND OFF .................................... 18
2.2.1 Turning On ...................................................................................... 18
2.2.2 Turning Off ...................................................................................... 19
2.3 CHANGING KEYPAD BACKLIGHT AND CONTRAST ........................... 19
2.4 SELECTING THE LANGUAGE ................................................................ 19
2.5 EXTERNAL CONNECTIONS ................................................................... 20
2.5.1 GPS Connection FOR CHARTPLOTTER WITH EXTERNAL GPS RECEIVER .. 20
2.5.2 Autopilot Connection ...................................................................... 22
2.5.3 External NMEA Connection ............................................................ 22
2.5.4 C-COM GSM Plus Connection ....................................................... 23
2.5.5 Beacon Receiver Connection ......................................................... 24
2.5.5.1 For Chartplotter with External GPS Receiver .................... 24
2.5.5.2 For Chartplotter with Internal GPS Receiver ..................... 24
2.6 ADDITIONAL C-CARDS ........................................................................... 24
2.6.1 Inserting C-CARD ........................................................................... 25
2.6.2 Removing C-CARD ......................................................................... 25
2.7 MENU OPTIONS ...................................................................................... 26
2.8 DATA ENTRY ........................................................................................... 26
3 For the New User ........................................................................................... 27
3.1 SCREEN DISPLAY CONFIGURATION ................................................... 27
3.1.1 Charts and Text Area ..................................................................... 27
3.1.2 Depth Graph ................................................................................... 29
3.1.3 GPS Data Page .............................................................................. 29
3.1.4 Navigation Data Page ..................................................................... 30
3.1.5 Graphic Data (Rolling Road) Page ................................................. 30
3.2 BASIC SETTINGS .................................................................................... 31
3.2.1 Course Vector ................................................................................. 31
3.2.2 Screen Amplifier ............................................................................. 31
3.2.3 Advanced Functions ....................................................................... 31
3.2.4 User Points ..................................................................................... 31
3.2.5 Depth Window ................................................................................ 31
3.2.6 Units Selection ................................................................................ 32
6User Manual
3.2.7 Nav Aids Presentation .................................................................... 32
3.2.8 Input/Output Menu .......................................................................... 32
3.2.8.1 Port 1/Port 2/Port 3 Input ................................................... 32
3.2.8.2 Port 1/Port 2/Port 3 Output ................................................ 33
3.2.8.3 Port 1/Port 2/Port 3 NMEA Output Messages Selection ... 33
3.2.8.4 GPS Setup Menu ............................................................... 33
Internal GPS FOR CHARTPLOTTER WITH INT. GPS RECEIVER .... 33
Restart GPS ....................................................................... 33
Differential Correction Source ........................................... 34
Navigation Speed .............................................................. 34
3.2.8.5 Send & Receive Marks/Routes .......................................... 34
3.2.8.6 C-Link ................................................................................. 34
3.2.8.7 Cable Wiring Page ............................................................. 34
3.2.9 C-Voice Menu ................................................................................. 34
3.2.9.1 Navigation ........................................................................... 34
3.2.9.2 Echosounder ...................................................................... 35
3.2.9.3 Output Port ......................................................................... 35
3.3 A-B-C-D FUNCTION ................................................................................ 35
3.3.1 Inserting the A-B-C-D points .......................................................... 35
3.3.2 Deleting the A-B-C-D points ........................................................... 36
3.3.3 Navigating on the A-B-C-D points .................................................. 36
3.4 NAVIGATING TO A SINGLE DESTINATION .......................................... 36
3.4.1 Distance and Bearing to Target ..................................................... 36
3.4.2 Time To Go ..................................................................................... 36
3.4.3 Deleting Target ............................................................................... 37
3.5 C-MAP NT MAX INFORMATION ............................................................. 37
3.5.1 Map Menu ....................................................................................... 38
3.5.1.1 Perspective View ............................................................... 38
3.5.1.2 Palette FOR COLOR CHART PLOTTER ...................................... 38
3.5.1.3 Map Orientation ................................................................. 39
3.5.1.4 Zoom Type ........................................................................ 39
3.5.1.5 Fonts & Symbols ............................................................... 39
3.5.1.6 Dynamic Nav-Aids ............................................................. 40
3.5.1.7 Mixing Levels ..................................................................... 40
3.5.1.8 Safety Status Bar ............................................................... 40
3.5.1.9 Currents Prediction ............................................................ 41
3.5.1.10 Other Map Configurations ................................................ 42
3.5.2 Getting Automatic Info .................................................................... 45
3.5.2.1 Info on objects with Pictures ............................................. 46
Change Picture Size .......................................................... 46
3.5.3 Info Tree and Expanded Info page ................................................. 46
3.5.4 Info Function ................................................................................... 47
3.5.5 Getting Port Info ............................................................................. 47
3.5.6 Getting Tide Info ............................................................................. 47
3.5.7 Find Function .................................................................................. 49
3.5.7.1 Finding Nearest Services .................................................. 49
3.5.7.2 Find Port ............................................................................ 49
Searching by name ............................................................ 49
Searching port into selected range ................................... 49
3.5.7.3 Finding Tide Stations ......................................................... 50
3.5.7.4 Finding Wrecks .................................................................. 50
3.5.7.5 Finding Obstructions .......................................................... 50
7
User Manual
3.6 MAN OVERBOARD (MOB) ...................................................................... 50
3.6.1 Inserting MOB .................................................................................. 50
3.6.2 Deleting MOB .................................................................................. 51
4 For the Experienced User ........................................................................................... 53
4.1 MORE ABOUT CREATING AND USING ROUTES ................................ 53
4.1.1 Waypoint ......................................................................................... 53
4.1.1.1 Adding Waypoint ............................................................... 53
4.1.1.2 Creating a route ................................................................. 54
4.1.1.3 Deleting Waypoint ............................................................. 54
4.1.1.4 Deleting route .................................................................... 55
4.1.1.5 Distance and Bearing to Target ......................................... 55
Time To Go ........................................................................ 56
Deleting Target .................................................................. 56
4.1.1.6 Moving Waypoint ............................................................... 56
4.1.1.7 Inserting Waypoint ............................................................. 57
4.1.1.8 Editing Waypoint ................................................................ 58
4.1.1.9 Finding info about Waypoints: User Points List page ....... 59
Finding User Points ........................................................... 59
Deleting selected User Point ............................................ 60
Deleting all User Points with the same symbol ................. 60
Deleting all User Points with the same type ..................... 60
Deleting all stored User Points .......................................... 60
Send/Receive User Points ................................................ 60
4.1.2 Routes ........................................................................................... 60
4.1.2.1 Selecting Route ................................................................. 60
4.1.2.2 Deleting route .................................................................... 61
4.1.2.3 Reversing route ................................................................. 61
4.1.2.4 Finding information about a route: Route Report .............. 61
Selecting route ................................................................... 62
Changing Speed & Fuel values ......................................... 62
Reversing route ................................................................. 62
Deleting route .................................................................... 62
4.1.2.5 Route Name ....................................................................... 62
4.1.2.6 Send/Receive Route .......................................................... 62
4.2 USING MARKS & EVENTS ...................................................................... 63
4.2.1 Marks ........................................................................................... 63
4.2.1.1 Adding Mark ....................................................................... 63
4.2.1.2 Deleting Mark ..................................................................... 63
4.2.1.3 Goto ................................................................................... 63
4.2.1.4 Moving Mark ...................................................................... 63
4.2.1.5 Editing Mark ....................................................................... 64
4.2.1.6 Finding information about Marks: User Points List page .. 65
4.2.1.7 Add to Route ..................................................................... 65
4.2.2 Events ........................................................................................... 65
4.2.2.1 Adding Event ..................................................................... 66
4.2.2.2 Deleting Event ................................................................... 66
4.2.2.3 Goto ................................................................................... 66
4.2.2.4 Editing Event ...................................................................... 66
4.2.2.5 Finding information about Events: User Points List page . 67
4.2.2.6 Add to Route ...................................................................... 67
4.3 MORE ABOUT A-B-C-D FUNCTION ....................................................... 67
8User Manual
4.3.1 Inserting the A-B-C-D points .......................................................... 67
4.3.2 Deleting the A-B-C-D Points ........................................................... 68
4.3.3 Deleting the A-B-C-D Segment ...................................................... 68
4.3.4 Moving the A-B-C-D points ............................................................. 68
4.3.5 Inserting the A-B-C-D points .......................................................... 68
4.3.6 Navigating on the A-B-C-D points .................................................. 68
4.4 USING THE TRACK FUNCTIONS ........................................................... 68
4.4.1 Selecting active Track .................................................................... 69
4.4.2 Enabling Track storing .................................................................... 69
4.4.3 Displaying Track ............................................................................. 69
4.4.4 Selecting track line pattern ............................................................. 69
4.4.5 Deleting Track ................................................................................ 69
4.4.6 Deleting Selected Track ................................................................. 69
4.4.7 Selecting Track memorizing type ................................................... 70
4.4.8 Selecting distance .......................................................................... 70
4.4.9 Selecting time ................................................................................. 70
4.5 USER C-CARD MENU ............................................................................. 70
4.5.1 Saving File ...................................................................................... 71
4.5.2 Loading File .................................................................................... 72
4.5.3 Deleting File .................................................................................... 72
4.5.4 Formatting Usr C-CARD ................................................................. 72
4.5.5 Changing UserC-CARD .................................................................. 72
4.6 C-LINK ........................................................................................... 73
4.6.1 How C-Link system works .............................................................. 73
4.7 C-LINK NAVIGATION DATA TRANSFER ............................................... 73
4.7.1 Operations ...................................................................................... 74
4.7.1.1 Introductive elements ........................................................ 74
4.7.1.2 C-Link serial connection .................................................... 75
4.7.1.3 Master Chart Plotter .......................................................... 75
Operating mode ................................................................ 75
4.7.1.4 Slave Chart Plotter ............................................................ 75
Operating mode ................................................................. 75
Stop current navigation ...................................................... 75
Inhibit Navigation operation ............................................... 76
Inhibit Route following ....................................................... 76
MOB handling .................................................................... 76
Notes .................................................................................. 76
4.7.1.5 C-Link navigation data: Acquisition and Display ............... 76
4.7.1.6 Graphical representation on Map Display ......................... 77
4.7.1.7 Route Data Report ............................................................. 77
4.7.1.8 Quick Info ........................................................................... 78
Route Navigation: Quick Info on the Destination .............. 78
Quick info on Single Destination ....................................... 78
5 Advanced Settings ........................................................................................... 79
5.1 SETUP ........................................................................................... 79
5.1.1 Time Reference ............................................................................... 79
5.1.2 Time Format .................................................................................... 79
5.1.3 Date Format ..................................................................................... 80
5.1.4 Wind Speed ..................................................................................... 80
5.1.5 Beeper ........................................................................................... 80
5.1.6 Extern Waypoint .............................................................................. 80
5.1.7 Backlight Timeout ............................................................................ 80
9
User Manual
5.2 FIX ........................................................................................... 80
5.2.1 Fix Correction ................................................................................... 81
5.2.2 Compute Correction ........................................................................ 81
5.2.3 Correction Offset ............................................................................. 81
5.2.4 Position Filter ................................................................................... 81
5.2.5 Speed Filter ..................................................................................... 81
5.2.6 Filter Dump ...................................................................................... 81
5.2.7 Dead Reckoning .............................................................................. 82
5.2.8 Static Navigation .............................................................................. 82
5.3 NAVIGATE ........................................................................................... 82
5.3.1 Coordinate System .......................................................................... 82
5.3.2 Fix Datum ......................................................................................... 82
5.3.3 Map Datum ...................................................................................... 83
5.3.4 Map Orientation and Resolution ...................................................... 83
5.3.5 Rolling Road Scale .......................................................................... 83
5.3.6 Reset Total and Partial Trip ............................................................. 83
5.4 COMPASS ........................................................................................... 83
5.4.1 Bearings ........................................................................................... 84
5.4.2 Variation ........................................................................................... 84
5.4.3 Calibration ........................................................................................ 84
5.5 ALARMS ........................................................................................... 84
5.5.1 Arrival Alarm .................................................................................... 84
5.5.2 XTE Alarm ........................................................................................ 85
5.5.3 Anchor Alarm ................................................................................... 85
5.5.4 Depth Alarm .................................................................................... 85
5.5.5 Grounding Alarm ............................................................................ 85
5.5.6 Grounding Alarm Range ................................................................. 86
5.5.7 Grounding Alarm Report ................................................................ 86
5.6 SIMULATION MENU ................................................................................ 86
5.6.1 Simulation Mode .............................................................................. 86
5.6.2 Speed ........................................................................................... 86
5.6.3 Heading ........................................................................................... 86
5.6.4 Date and Time ................................................................................. 87
5.6.5 Cursor Control ................................................................................. 87
5.7 C-STAFF ........................................................................................... 87
5.8 C-METEO ........................................................................................... 87
5.9 FISH FINDER MENU ............................................................................... 88
6 For the Technician ........................................................................................... 89
6.1 DIMENSIONS ........................................................................................... 89
6.2 INSTALLATION AND REMOVING ........................................................... 90
6.3 EXTERNAL WIRING ................................................................................ 92
6.4 TYPICAL CONNECTIONS ....................................................................... 93
6.5 TROUBLESHOOTING .............................................................................. 96
6.5.1 Problems and Solutions .................................................................. 96
6.5.2 Help ........................................................................................... 96
6.5.3 If you need assistance .................................................................... 96
6.5.3.1 World Background Charts ................................................. 97
Worldwide Background Update ......................................... 97
6.6 SYSTEM TEST ......................................................................................... 97
6.6.1 RAM Menu ...................................................................................... 98
6.6.2 Dim Menu ....................................................................................... 98
10 User Manual
6.6.3 Cartridges ....................................................................................... 98
6.6.4 Serial Ports ..................................................................................... 99
6.6.5 Modem Test .................................................................................... 99
A Terms ......................................................................................... 101
B Smart DGPS WAAS Receiver ........................................................................................ 107
B.1 TECHNICAL SPECIFICATIONS ............................................................ 107
B.1.1 Pysical Characteristics ................................................................. 107
B.1.2 Electrical Characteristics .............................................................. 107
B.1.3 GPS Performance ........................................................................ 107
B.1.4 Environmental Characteristics ..................................................... 108
B.2 WIRING ......................................................................................... 108
B.3 SOFTWARE INTERFACE ...................................................................... 108
B.4 MECHANICAL CHARACTERISTICS & MOUNTING ............................. 109
B.4.1 Installing ........................................................................................ 109
B.4.2 Dimensions ................................................................................... 110
Analytical Index ......................................................................................... 111
11
User Manual
1
Introduction
Congratulations on your purchase of the chartplotter!
If you have not used a position-finding instrument before and intend to use
your chartplotter for navigating, we suggest you should read this User Manual and
make sure you are familiar with its contents.
The User Manual is divided into three main parts. Chapter "Before You
Begin" introduces you to the basic information to get you start using the chartplotter.
Chapter "For the New User" should be read first to become familiar with your new
instrument. Chapter "For the Experienced User" introduces the advanced features
of the chartplotter.
1.1 CONVENTIONS
Throughout this user manual, the keys are shown in capitals letters enclosed
between single inverted commas, for example 'MENU'.
Menu operations are in bold characters listed by keys sequence with the
menu names enclosed between inverted commas, for example 'MENU' + "BASIC
SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' means: press the
'MENU' key, using the cursor key to select the Basic Settings menu, press 'ENTER',
using the cursor key to select the Input/Output menu and then press 'ENTER'.
Terms and functions underlined, for example Target, are explained in the
Appendix "Terms".
12 User Manual
1.2 FEATURES
The chartplotter is a computer specifically designed for nautical use but, more
precisely, to ease and speed up all calculations, which so far have been done manu-
ally. If connected to a positioning instrument, the chartplotter displays the current
position, the speed, and the heading of the boat and its Track. The user information
like Waypoints, Marks and Tracks can then be stored on a User C-CARD and can be
recalled at any time. On the screen are shown navigation data and cartographic in-
formation obtained from electronic charts of C-MAP C-CARD.
When the package containing the chartplotter is first opened, please check it
for the following contents (if any parts are missing contact the dealer the chartplotter
was purchased from):
Quick disconnect bracket and its protective cover
Chartplotter's protective cover
User Manual
Note FOR COLOR CHARTPLOTTER
Fuse 2 Amp. + fuseholder.
Note FOR CHARTPLOTTER WITH EXTERNAL GPS RECEIVER
Tha package contains the following parts too: Flush mounting kit; Smart DGPS WAAS Receiver
with cable 15 mt/45 feet.
C-MAP C-CARD (cartography data cards) are available through your local
dealer. For additional information on C-MAP Cartography visit web site at www.c-
map.com.
1.2.1 SPECIFICATIONS
1.2.1.1Main Characteristics
Recordable Individual points
User Points : 500
Type of User Points : 16
Routes
Routes : 25
Max User Points per Route : 100
Tracking
Tracks : 2
Points per Track : 1000
Step by Distance : 0.01, 0.05, 0.1, 0.5, 1, 2, 5, 10 Nm
13
User Manual
Step by Time : 1, 5, 10, 30 Sec, 1, 5, 10 Min
Cartographic Functions
Detailed Map by using C-MAP C-CARD
Coordinates System (ddd mm ss, ddd mm.mm, ddd mm.mmm, UTM, OSGB, TD)
Map Datum
Display Mode (Full, Simple, Fishing, Low, Custom)
Marine
Names, Buoys ID, Nav-Aids, Light Sectors, Attention Areas, Tides & Currents,
Seabed Type, Ports & Services, Tracks & Routes, Underwater Objects
Depth
Depth Areas, Depth Areas Min/Max, Rocks Min/Max
Land
Lan Elevation values, Roads, POIs
Chart
Lat/Lon Grid, Chart Boundaries, Value-Added data
Map Menu
Zoom Type
Fonts & Symbols
Perspective View
Live Nav-Aids
Map Orientation (North, Head, Course)
Mixing Levels
Safety Status Bar
Palette
Currents Prediction
Fix Functions
Fix Correction (manual and automatic)
Position Filter
Speed Filter
Dead Reckoning
Screen Amplifier
Reset Total and Partial Trip
Rolling Road Scale
Fix Datum
Compass Calibration
Bearings True and Magnetic
Variation user selectable
Course Vector
Static Navigation
14 User Manual
A-B-C-D Function
Report Functions
Depth window
GPS Data page
Navigation Data page
Grafic Data page
Depth Graph page (1/2 screen and 1/3 screen)
About page
Special Functions
C-Link, C-Meteo and C-Staff
Fish Finder capability if connected to Fish Finder Black Box
Automatic Info
Find (Ports Services, Ports, Tide Stations, Wrecks, Obstructions)
Navigation to Destination
Speed Unit (Mph, Kts, Kmh)
Distance Unit (Km, Nm, Sm)
Depth Unit (Ft, FM, Mt)
Altitude Unit (Ft, FL, Mt)
Temperature Unit (°C, °F)
Alarms Handling
Arrival Alarm, XTE Alarm, Anchor Alarm, Depth Alarm, Grounding Alarm,
Grounding Alarm Range, Grounding Alarm Report
MOB Function
Simulation
Speed, Heading,, Date, Time, Cursor Control, Simulation On/Off
Auxiliary Memory
User C-CARD 1/2/4 MB
Interface
2 port I/O (only for chartplotter WITH Internal GPS Receiver)
3 ports I/O (only for chartplotter WITH External GPS Receiver)
1.2.1.2 Phisical Characteristics
Chartplotter size (inch/mm)
Gray Levels/Color: see Par. 6.1 for the related picture
Weight
Gray Levels: 800 g
Color: 950 g
LCD Display
Gray Levels: transflective LCD (active area 5.6")
15
User Manual
Color: Sun Light Viewable LCD (active area 5.6")
Resolution: 320 x 240 pixels
Power consumption
Gray Levels: 5 Watt, 10–35 Volt DC
Color: 7.5 Watt, 10–35 Volt DC
Operating Temperature Range
From 0°C to 55°C (from 32°F to 131°F)
Memory
Non volatile with battery back-up
Keyboard
Backlighted, silicon rubber
1.3 BASICS
The chartplotter is controlled by using ten keys. There is also a cursor key to
move a cursor across the screen. As you press a key, a single audio beep confirms the
key action; every time the key pressed is not valid, three rapid beeps sound indicates
that no response is available.
Fig. 1.3 - The chartplotter
16 User Manual
17
User Manual
2
Before You Begin
This chapter provides basic information to get you start using the chartplotter;
it will help you to become familiar with the chart display and the functions of the
controls before you start using the chartplotter.
2.1 THE KEYBOARD
The 'CONTRAST'/'BACKLIGHT'/'POWER' key
Press and hold the right side of 'POWER' for 1 second to turn the chartplotter
On. Press and hold the right side of 'POWER' down (once the chartplotter has been
turned On) for 3 seconds turns the chartplotter Off.
Press and immediately release the right side of 'POWER' to adjust the back-
light, press and immediately release the left side of 'POWER' to adjust the contrast
of the display.
The key
Press 'MENU' to select the Functions Menu.
The key
Place the cursor and press 'GO-TO' to set Target.
The key
Press 'PAGE' to select the configuration you wish among cartography and
text area in two different modes (text area on the right side or on the bottom line of
the screen, full screen if Target has been inserted or with partial information on
SOG), only cartography, Depth Graph 1/2 screen and 1/3 screen pages, GPS Data
page, Navigation Data page, Graphic Data page.
The key
Press 'MODE' to set the Navigate mode (Home)
18 User Manual
The key
Press 'MOB' to set MOB (Man OverBoard). When MOB is activated, press
'MOB' to delete it.
The key
Press 'CLEAR' to exit from menu or to leave a menu without making changes.
In Basic Mode deletes the A, B, C, D points, the User Point (Mark, Event, Waypoint),
the MOB, the Target identified by the cursor.
The key
Press 'ENTER' to select the desired option, to confirm selection; in Basic
Mode places A, B, C, D points on the cursor coordinates, in Advanced Mode creates
Objects (Mark,, Event, Waypoint, A-B-C-D).
The cursor key
The cursor key moves the cursor about on the display screen, quickly and
accurately. It also scrolls the desired option in the menu page(s). If in Navigate (Home)
mode, it allows to exit from Navigate mode.
The and keys
Press 'ZOOM IN' shows more details of a smaller area, by changing the
chart scale and zooming in on your display. Press 'ZOOM OUT' to operate simi-
larly to the 'ZOOM IN', except in reverse, changing the scale and showing a wider,
otherwise less detailed view.
2.2 TURNING THE CHARTPLOTTER ON AND OFF
Before powering On the chartplotter, check for the correct voltage (10-35
volt dc, see Par. 6.3) and the correct connections with the positioning instrument
(see Par. 2.5).
2.2.1 TURNING ON
Press and hold the right side of 'POWER' for 1 second. The chartplotter
19
User Manual
emits one rapid beep sound and a title page is opened.
After a few seconds, the first of the two Caution Notice pages is displayed,
reminding you that the chart plotter is only an aid to navigation, and should be used
with appropriate prudence. The electronic charts are not intended to substitute for
the official charts. Then the cartographic screen is displayed.
2.2.2 TURNING OFF
Press the right side of 'POWER' and hold for 3 seconds: a countdown timer
appears on the screen, if you release the key before the countdown timer reaches
zero, the chart plotter will remain On.
2.3 CHANGING KEYPAD BACKLIGHT AND CONTRAST
Press and immediately release the right side of 'POWER' (do not press and
hold the key, or the "power-off" message will be displayed!): the backlight increases.
Repeat this operation the backlight decreases.
Press and immediately release the left side of 'POWER': the contrast increases.
Press and immediately release the left side of 'POWER' the contrast decreases. In
other words, first pressure of the key will increase the value till you keep it pressed,
next pressure of the key will decrease the value till you keep it pressed.
Warning!!!
At low temperatures the CCFL backlight may not glow properly. allow a few minutes to warm
up.
2.4 SELECTING THE LANGUAGE
It is possible to select the language in which you wish information to be
displayed (for screen labels, menus and options, but it is not affect the map informa-
tion). The default setting is Italian.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "LANGUAGE" + 'ENTER'
Choose the language you want and press 'ENTER' to confirm.
20 User Manual
2.5 EXTERNAL CONNECTIONS
2.5.1 GPS CONNECTION
FOR CHARTPLOTTER WITH EXTERNAL GPS RECEIVER
Connect the GPS to the Port 3: see the picture in Fig. 2.5.1.
Control the input setting following the procedure:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"PORT 3 INPUT" + 'ENTER' + "NMEA-4800-N81-N" + 'ENTER'
The GPS can be connected also to the Port 1 and 2, in this case select
NMEA0183-4800-N81-N on the used port.
21
User Manual
Fig. 2.5.1 - GPS Connection on Port 3
22 User Manual
2.5.2 AUTOPILOT CONNECTION
To connect the Autopilot to the Port 2 see the following picture:
Fig. 2.5.2a - Autopilot Connections on Port 2
To choose your preferred setting follow the procedure:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"PORT 2 OUTPUT" + 'ENTER'
Then choose your preferred setting among the NMEA available settings
NMEA 0183 4800-N81-N, NMEA 0180, NMEA 0180/CDX (the default setting is
NMEA 0183 4800-N81-N) and press 'ENTER' to confirm.
The autopilot can be connected also to the Port 1 and 3, in this case select the
output format on the used port.
2.5.3 EXTERNAL NMEA CONNECTION
To connect the External NMEA to the Port 1 see the following picture:
Fig. 2.5.3 - External NMEA Connections on Port 1
23
User Manual
To choose your preferred setting follow the procedure:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"PORT 1 INPUT" + 'ENTER'
Then choose your preferred setting among the NMEA available settings
NMEA 1200-N81-N, NMEA 4800-N81-N, NMEA 4800-N82-N, NMEA 9600-O81-
N, NMEA 9600-N81-N (the default setting is 4800-N81-N) and press 'ENTER' to
confirm.
An NMEA device can be connected also to the Port 2 and 3, in this case
select the format on the used port. Doing connection remember that only the Port 1
is optoisolated in input.
2.5.4 C-COM GSM PLUS CONNECTION
To connect the modem C-COM to the chart plotter with quick disconnect
bracket follow the procedure:
1. Cut the C-COM cable about 5 cm from the "T" connector:
Fig. 2.5.4 - C-COM cable
2. Connect the wires to the quick disconnect bracket cable as follows:
Fig. 2.5.4a - Connection for the Port 1
Note
The connection is valid for the C-COM IR and C-COM RS232 too.
24 User Manual
3. Set the C-COM for Port 1 as follows:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"PORT 1 INPUT" + 'ENTER' + "C-COM" + 'ENTER'
The C-COM can be connected also to the Port 2 and 3, in this case select the
format on the used port.
2.5.5 BEACON RECEIVER CONNECTION
2.5.5.1 For Chartplotter with External GPS Receiver
To connect a Differential Beacon Receiver see Fig. 2.5.1.
2.5.5.2 For Chartplotter with Internal GPS Receiver
To connect a Differential Beacon Receiver see the following picture:
Fig. 2.5.5.2 - Beacon Receiver Connection
2.6 ADDITIONAL C-CARDS
The chartplotter uses two types of C-MAP cartridges: either a chart cartridge
25
User Manual
or a data storage cartridge. A chart cartridge, called C-CARD, contains detailed charts
of the area covered. A data storage cartridge, called User C-CARD can be used to
permanently store your routes, Waypoints, Marks, Events and tracks.
Note
During normal operations the C-CARD should not be removed since the chart plotter may lock
up.
2.6.1 INSERTING C-CARD
Hold the C-CARD by the short inclined side so that you can see the C-MAP
label.
Fig. 2.6.1 - Inserting C-CARD (I)
Gently push the C-CARD into one of the two slots (1); push the C-CARD
in as far as it will go, then move it to the bottom (2) to hold fixed into the slot (3).
Fig. 2.6.1a - Inserting C-CARD (II)
2.6.2 REMOVING C-CARD
Press lightly the C-CARD you wish to remove (1) and move it to the top (2)
until you hear a click: the C-CARD will ejected out of the slot (3).
26 User Manual
Fig. 2.6.2 - Removing C-CARD
Note
C-MAP is continuously creating new charts and revising old ones. If you wish to receive
information on the newest availbale charts, you can write for the catalog of available
C-MAP C-CARD at your dealer.
2.7 MENU OPTIONS
You may select how the chartplotter displays primary information (such as
how time is displayed) from the main Menu. Refer to Chapter 5 for more information.
'MENU'
2.8 DATA ENTRY
Information is keyed into the chartplotter when editing a Waypoint, enter-
ing a Route or using the Fix Correction functions. When the field is highlighted:
- Enter or edit data by pressing up/down cursor key to step through the
available characters until the preferred character is displayed.
- Press right cursor key to move the cursor to the right.
- Use left cursor key to move the cursor to the left.
27
User Manual
3
For the New User
In order to get started using your chartplotter, you must do the following
things:
1) Your chartplotter must have been installed properly according to the in-
stallation instruction on Par. 6.2.
2) You must have performed the proper settings for use with your position-
ing instrument (see Par. 2.5 and 2.6) and inserting the C-CARD for navigating in
area you wish (see Par. 2.7).
3) You must have Power On to the chartplotter and adjust the brightness
and contrast of the display (see Par. 2.2 and 2.3).
Once this is done, you can use your chartplotter for navigation.
3.1 SCREEN DISPLAY CONFIGURATION
The screen display can be shown in different modes (wrap around) among
cartography and text area in two different modes (text area on the right side or on
the bottom line of the screen, complete if Target has been inserted or with partial
information on SOG), only cartography, Depth Graph 1/2 screen and 1/3 screen
pages, GPS Data page, Navigation Data page, Graphic Data page. To select the con-
figuration you wish:
'PAGE' more times
3.1.1 CHARTS AND TEXT AREA
The charts and text area can be shown in two different modes. The first is
with text area on the right side of the screen:
28 User Manual
Fig. 3.1.1 - Charts and text area
The second is with text area on the bottom line of the screen (with partial
information on SOG):
Fig. 3.1.1a - Charts and text windows
If Target is set, in the previous Fig. 3.1.1a instead of the only SOG information
window, a text line with DST, BRG, XTE, SOG and TTG information appears.
Then it is possible to see on the screen only charts:
Fig. 3.1.1b - Full charts
29
User Manual
3.1.2 DEPTH GRAPH
The Depth graph can be shown in two different modes. Depth graph dis-
played only on 1/3 of the screen:
Fig. 3.1.2 - The Depth Graph 1/3 of the screen
or Depth graph displayed on 1/2 of the screen:
Fig. 3.1.2a - The Depth Graph 1/2 of the screen
3.1.3 GPS DATA PAGE
The GPS Data page shows in graphic mode GPS data.
Fig. 3.1.3 - GPS Data Page
30 User Manual
On the right side of the screen (see Fig. 3.1.3), there is a polar representation of the
azimuth and elevation of each satellites. The circle contains a number indicating the PRN of the
satellite and it is filled when it is used for the fix solution. On the left side there are histograms
indicating the S/N ratio (SNR). The bar is filled when the satellite is used for solution. As
example, the satellite with PRN=10 is used for solution with S/N=44, Azimuth=127degree
and Elevation=70degree. When a valid fix is received, the Lat/Lon, Date, Time, Altitude,
VDOP, HDOP, SOG and COG are shown in the page.
3.1.4 NAVIGATION DATA PAGE
The Navigation Data page shows information about speed (SOG) and course
(COG) of the ship, status of the received signal, ship's coordinate and other general
information.
Fig. 3.1.4 - Navigation Data Page
3.1.5 GRAPHIC DATA (ROLLING ROAD) PAGE
The Graphic Data Page shows in graphic mode navigation data.
Fig. 3.1.5 - Graphic Data Page
31
User Manual
3.2 BASIC SETTINGS
The Basic Settings Menu provides access to the set up functions. Here you
can choose the language you want (see Par. 2.4).
'MENU' + "BASIC SETTINGS" + 'ENTER'
3.2.1 COURSE VECTOR
Disables (Off) or sets time as : 2, 10, 30 min, 1, 2 hours, Infinite. The default
setting is Infinite.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "COURSE VECTOR" + 'ENTER'
3.2.2 SCREEN AMPLIFIER
The Screen Amplifier function allows, when it is On and Home mode is set,
to place map on the screen related to the fix position and direction, so the map
shown is that before the ship. The default setting is On.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "SCREEN AMPLIFIER" + 'ENTER'
3.2.3 ADVANCED FUNCTIONS
The chartplotter can operate in two different modes: Advanced Mode and
Basic Mode. In Advanced Mode it is possible to have more available functions, oth-
erwise in Basic Mode there is a restricted number of functions (see Chapter 4). When
Advanced Functions is On the chartplotter works in Advanced Mode, otherwise
when it is Off the chartplotter works in Basic Mode. The default setting is Off.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "ADVANCED FUNCTIONS" + 'ENTER'
3.2.4 USER POINTS
Turns On/Off/Icon the displaying of the User Point Name. The default setting
is On.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER'
3.2.5 DEPTH WINDOW
Turns On/Off the displaying of the Depth Window on the screen. The de-
fault setting is Off.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "DEPTH WINDOW" + 'ENTER'
32 User Manual
3.2.6 UNITS SELECTION
Allows to select the preferred unit for Distance, Speed, Depth and Altitude
(altitude of GPS Antenna on the medium sea level).
Speed: Kts(knots)/Mph(miles per hour)/Kph(chilometres per hour). The default set-
ting is Kts.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "SPEED" + 'ENTER'
Distance: Nm(Nautical Miles)/Sm(statute miles)/Km(chilometres). The default setting
is Nm.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "DISTANCE" + 'ENTER'
Depth: Ft(Feet)/FM(Fathoms)/Mt(Meters). The default setting is Ft.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "DEPTH" + 'ENTER'
Altitude: Ft(Feet)/FL(Flight Level)/Mt(Meters). The default setting is Ft.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "ALTITUDE" + 'ENTER'
Temperature: °C/°F. The default setting is °C.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "TEMPERATURE" + 'ENTER'
3.2.7 NAV AIDS PRESENTATION
Allows to set the Nav Aids presentation as US or INTERNATIONAL. The
default setting is INTERNATIONAL. When selected it affects Lights, Signals, Buoys
& Beacons display.
- INT(International): Draws Nav-Aids using international symbology. All
components of Complex Objects are shown.
- US: Draw Nav-Aids using NOAA symbology. All components of Com-
plex Objects are shown.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "NAV AIDS PRESENTATION" +
'ENTER'
3.2.8 INPUT/OUTPUT MENU
3.2.8.1 Port 1/Port 2/Port 3 Input
Sets or disables the format for the navigation data input serial Port1/2/3.
The default setting is NMEA-0183 4800-N81-N. For example to set the Port 2 as
NMEA-0183 (4800 Baud Rate, Parity None, 8 Bits Number, 1 Stop Bit and Normal
Polarity) you must select:
33
User Manual
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"PORT 2 INPUT" + 'ENTER'+ "NMEA-0183 4800-N81-N" + 'ENTER'
Note
The option C-COM defines on which Port (both Input and Output) the C-COM modem is connected.
It is important to remark that this setting affects the Input and the Output of the selected Port. C-COM
can only be set on one Port at time. If C-COM was already assigned to a Port and the user tries to
set the C-COM to another Port, the chart plotter will show a message that warns the user about the
current settings and asks if the new settings must overwrite the previous ones.
3.2.8.2 Port 1/Port 2/Port 3 Output
Sets or disables the output interface. The default setting is NMEA-0183 4800-
N81-N. For example to set the Port 2 as NMEA-0180 you must select:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"PORT 2 OUTPUT" + 'ENTER'+ "NMEA-0180" + 'ENTER'
Note
Selecting NMEA-0180 or NMEA-0180CDX the chart plotter shows a message to advise the user
that the related input will be disabled.
3.2.8.3 Port 1/Port 2/Port 3 NMEA Output Messages Selection
The chart plotter allows customizing the NMEA-0183 sentence transmitted
on each port. The default setting is GLL, VTG, XTE, RMB, RMC, APB On and
BOD, BWC, RMA, WCV, GGA, HSL , HDG Off.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"PORT 1/2/3 OUTPUT SENTENCES" + 'ENTER'
3.2.8.4 GPS Setup Menu
It is possible to set the your preferred configuration for the connected GPS.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"GPS SETUP" + 'ENTER'
Note
This item is shown alternately to the selection of the output messages when to the related port is
connected a GPS identificable by the chart plotter.
Internal GPS FOR CHARTPLOTTER WITH INTERNAL GPS RECEIVER
Enables (On) or disables (Off) the Internal GPS. The default setting is On.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"GPS SETUP" + 'ENTER' + "INTERNAL GPS" + 'ENTER'
Restart GPS
Restars all GPS processes. Once executed, the message "Done" is shown.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"GPS SETUP" + 'ENTER' + "RESTART GPS" + 'ENTER'
34 User Manual
Differential Correction Source
Allows setting what kind of Differential Correction will be used by the GPS be-
tween WAAS-EGNOS and RTCM (beacon correction). The default setting is WAAS-
EGNOS.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"GPS SETUP" + 'ENTER' + "DIFF CORRECTION SOURCE" + 'ENTER'
Navigation Speed
Allows setting the Navigation Speed among Low Speed, Medium Speed and High
Speed.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"GPS SETUP" + 'ENTER' + "NAVIGATION SPEED" + 'ENTER'
3.2.8.5 Send & Receive Marks/Routes
Sets the desired port used for transferring User Points and Routes functions:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"SEND/REC ROUTES & MARKS" + 'ENTER' + "Port1/Port2/Port3" + 'ENTER'
3.2.8.6 C-Link
Selects the Master unit (Primary Station) or the Slave unit (Secundary Station):
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"C-LINK" + 'ENTER' + "Secundary Station/Primary Station" + 'ENTER'
3.2.8.7 Cable Wiring Page
Shows a window containing the inteface cable wiring. See Par. 6.3 and 6.4.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"CABLE WIRING" + 'ENTER'
3.2.9 C-VOICE MENU
AVAIBLE IF THE CHARTPLOTTER IS CONNECTED TO THE VOICE NAVIGATION SYSTEM
FOR MORE DATAILS SEE YOUR LOCAL DEALER
The chartplotter has two different vocal modes, Navigation and Echosounder.
According to what mode is selected the messages spoken from the chartplotter are
different.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "C- VOICE" + 'ENTER'
3.2.9.1 Navigation
Enables (On), disables (Off) or insert the time (2, 5, 10, 15 minutes) for the
Navigation Voice mode. If it is On, the message is always sent, as fast as possible. Instead
if it is one among the available values, for example 2 minutes, the message is sent related
35
User Manual
to the selected time, in the previous example every two minutes.
'MENU' + "BASIC SETTINGS" + 'ENTER' +"C- VOICE" + 'ENTER' + "NAVIGA-
TION" + 'ENTER'
3.2.9.2 Echosounder
Enables (On) or disables (Off) the Echosounder Voice mode. If it is On, the
Depth message is spoken. The message is spoken if a valid depth data is received by
the chartplotter or if it is in Simulation mode. The default setting is Off.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "C- VOICE" + 'ENTER' +
"ECHOSOUNDER" + 'ENTER'
3.2.9.3 Output Port
Selects the Output Port for the Voice function. The default setting is Port 1.
'MENU' + "BASIC SETTINGS" + 'ENTER' + "C- VOICE" + 'ENTER' + "OUTPUT
PORT" + 'ENTER'
3.3 A-B-C-D FUNCTION
The A-B-C-D function allows you to create the A, B, C, D points and to
delete them.
3.3.1 INSERTING THE A-B-C-D POINTS
Place the cursor on the desired position and press 'ENTER': on the screen
the A point and an information window on A appear. Move the cursor and press
'ENTER' again: the B point appears, connected to A with a straight segment; an
information window on A-B segment (distance (DST), bearing (BRG) and total dis-
tance from the first point) appears. Moving the cursor and pressing 'ENTER' places
the C and D points:
Fig. 3.2.1 - A-B-C-D points
36 User Manual
3.3.2 DELETING THE A-B-C-D POINTS
Place the cursor on the desired point (A, B, C or D) and press 'CLEAR': the
point is deleted. When the point is deleted, the cursor is placed on the previous
point, if existed. The labels of the next points are renamed.
3.3.3 NAVIGATING ON THE A-B-C-D POINTS
If fix received is good, place the cursor on the desired point A, B, C or D and
press 'GO-TO'. When the ship arrives to the Destination point, navigation follows
to the next point (if existed).
3.4 NAVIGATING TO A SINGLE DESTINATION
3.4.1 DISTANCE AND BEARING TO TARGET
Once you have positioned the cursor on your desired location (a generic
point on the map) press 'GO-TO'.
Fig. 3.4.1 - Navigation to a single destination
On the screen is shown a straight line connecting the Target (called DEST)
with the ship's position and an information window with Target position, that dis-
appears when the cursor is moved from the Target. When the Target is placed, all
navigation data are referred to this Target.
Note
When the chartplotter is turned Off, the Target does not remain in memory.
3.4.2 TIME TO GO
When the Target is set the TTG value is displayed in the Graphic Data page
and in the Navigation page:
37
User Manual
'PAGE' more times
Note
If SOG value is less than 1.0 knots or the BRG is greater than 90 degrees, the TTg value is not
displayed.
3.4.3 DELETING TARGET
Press cursor on Target icon, press 'CLEAR': the symbol identifies Target
disappears from the screen.
Otherwise (when the cursor is placed in a generic position on the chart)
press 'GO-TO'. A window appears to advise that the Destination is present: select
the item "STOP" and press 'ENTER', the symbol identifies Target disappears from
the screen.
Note
If you select the "START" item and press 'ENTER', the Target icon is moved on the new cursor
position.
3.5 C-MAP NT MAX INFORMATION
MAX is a major evolution of the NT/NT+ product technology. Key points are:
New Data Features
- Tides and Currents (intuitive arrows show direction and strength)
- World Background Charts with terrestrial data
- Value Added Data (Pictures and Diagrams, Land Data)
- Enhanced Port Info
New Presentation Features
- Clear View (advanced legibility techniques providing more chart data on the screen)
- Clear Info (sophisticated "Human Disctionary" to translate Nav-Aid abbreviations
found on paper cahrts)
- Dynamic Fonts and Symbols
- Dynamic Nav-Aids (an innovative and dynamic presentation mode)
- Flexi-Zoom (increased Under and Over Zoom between chart levels, resulting in
optimal scale display for any situation)
- Dynamic Elevation Data (optimised palettes for chart plotters with 256 or more
colors; inludes new NOAA palette for US market)
38 User Manual
- Perspective View ("Real World" perspective view of the chart, updated realtime
during navigation)
MAX and NT/NT+ C-CARD coexistence
- When NT+ data and MAX data cover different areas, the chart plotter gets data
from both charts (depending on the current position).
- When NT+ data and MAX data cover the same area, the chart plotter gets data only
from MAX chart.
3.5.1 MAP MENU
It is possible to select the Map Menu following the procedure:
'MENU' + "MAP SETTINGS" +'ENTER'
3.5.1.1 Perspective View
'MENU' + "MAP SETTINGS" +'ENTER' + "Perspective View" + 'ENTER'
Chart data may be projected in perspective mode during navigation. This
function allows setting the panoramic View of the chart.
As the upper side of the map is more compressed than the lower side, a wider map
area is visible. The perspective view allows showing more chart information immedi-
ately ahead and around the cursor.
Fig. 3.5.1.1 - Perspective View
3.5.1.2 Palette
FOR
C
OLOR
C
HART
P
LOTTER
'MENU' + "MAP SETTINGS" +'ENTER' + "Palette" + 'ENTER'
It is possible to set the palette used to enhance the visibility of the screen
depending on the surrounding light condition. The possible choices are Normal,
Classic, NOAA, Night Vision and Sunlight. The default setting is Classic. Normal
is recommended when the chartplotter is not exposed to the direct sunlight. When
39
User Manual
this mode is set the maps are displayed in order to use colors as similar as possible to
the ones used in the original paper charts. Classic uses more vivid colors. Night
Vision is recommended when the environment is dark in order to reduce the glare
of the display. The chartplotter displays maps and screen in darker colors. Sunlight
is designed to enhance the visibility of the screen when the chartplotter is exposed to
the sunlight. The maps are much brighter than in the other modes and the depth
areas are filled with white color so different depth areas are not easily distinguish-
able. NOAA allows setting NOAA paper chart colors presentation.
3.5.1.3 Map Orientation
'MENU' + "MAP SETTINGS" +'ENTER' + "Map Orientation" + 'ENTER'
Selects the orientation of your chart according to: North (the map is shown
with North upwards), Head (the map is shown with the ship's current heading up-
wards), Course (the map is displayed with the currently selected course leg upwards).
The default setting is North
It is possible to select the resolution angle for the Map Orientation.
3.5.1.4 Zoom Type
'MENU' + "MAP SETTINGS" +'ENTER' + " Zoom Type" + 'ENTER'
This feature allows more expansions or compression of the chart scale while
zooming in or out. Zoom Mode has two options; STANDARD (default) or FLEXI-
ZOOM. When in FLEXI-ZOOM mode, a short 'ZOOM...' push causes a change of
chart, whilst a long 'ZOOM...' push (press and hold) causes a pop-up window to be
displayed on a corner of the screen. The window shows the current Zoom Factor.
By pressing 'ZOOM IN'/'ZOOM OUT' the map is expanded or compressed
according to the zoom factor selected.
The Window is automatically closed if 'ZOOM...' is not pressed for 2 sec-
onds and the selected zoom factor will be used at the next zoom in/out.
3.5.1.5 Fonts & Symbols
'MENU' + "MAP SETTINGS" +'ENTER' + "Fonts & Symbols" + 'ENTER'
On MAX charts it is possible to set the size of all names and symbols drawn on
the charts, selecting between Normal size (the regular characters size) and Large size.
40 User Manual
Fig. 3.5.1.5 - Example of Normal size (on the left side) and Large side (on the right side) settings
3.5.1.6 Dynamic Nav-Aids
'MENU' + "MAP SETTINGS" +'ENTER' + "Dynamic Nav-Aids" + 'ENTER'
This function allows settings blinking lights on Nav-Aids. The blink period
and color of each Nav-aid is read from the Nav-Aid attributes available on the data
cartridge. When the ship is inside the Nav-Aid nominal range, the light of the Nav-
Aid will start blinking.
3.5.1.7 Mixing Levels
'MENU' + "MAP SETTINGS" +'ENTER' + "Mixing Levels" + 'ENTER'
When the map coverage at the current zoom level does not fill the entire
screen, the chartplotter draws the rest of the map expanding the cartographic infor-
mation read from, at most, two zoom levels above the current zoom level. For this
reason the map is drawn three times: firstly it draws the two levels before the current
level and then the current level. The area covered by the cartographic data read from
the previous levels is identified by a dotted pattern. When the cursor is moved on an
area not covered by data of the current level the chartplotter zooms out to the first
level covered by cartographic data. The default setting is Off.
Note
The Mixing Levels function works only with the new C-CARDs. It also affects the speed of the
redraw of the screen. If this function is not used it maybe disabled.
3.5.1.8 Safety Status Bar
'MENU' + "MAP SETTINGS" +'ENTER' + "Safety Status Bar" + 'ENTER'
This feature displays a status bar with six boxes showing the status of certain
functions. Any warning or alarm condition is identified by the red colour to indicate
possible risk.
41
User Manual
Fig. 3.5.1.8 - Safety Status Bar
Boxes definition is as follows:
Zoom
- Normal: when the chart is displayed at normal scale.
- U. Zoom: red when the chart is under-zoomed out more than twice nor-
mal scale, gray otherwise.
- O. Zoom: red when the chart is over-zoomed in more than twice normal
scale, gray otherwise.
- Chart Lock: red when the chart is zoomed in more than twice normaln
scale, gray otherwise.
Best Scale
Red when a more detailed chart is available under the cursor position.
Data Off
Red when at least one of the following objects or layers is turned off (by the
user): Depths/soundings; Wrecks/obstructions; Tracks/routes; Attention ar-
eas; Nav-Aids.
Clear View
Displays when Clear View function is On.
Dangers
Red when “Guardian Technology” detects one of the following objects: Land,
Intertidal, Depth Area, Rocks, Obstructions, Shoreline Constructions, Fish-
ing Facility, Wrecks, Dragged area, Diffusion area, Mooring facilities, Pingos
and Production installations.
Caution
Red when “Guardian Technology” detects cautionary or restricted area.
3.5.1.9 Currents Prediction
'MENU' + "MAP SETTINGS" +'ENTER' + "Currents Prediction" + 'ENTER'
It is possible to see the variation of the Tidal arrows on the selected area at
any given time. A window is shown on the low-left side of the chart, press 'ENTER'
to set the date and time manually, 'MENU' to decrease time and 'GOTO' to in-
crease time.
42 User Manual
3.5.1.10 Other Map Configurations
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
This function allows the user to customize the following selections and is
divided into the following setting: Marine Settings, Depth Settings, Land Settings
and Chart Settings.
Display Mode: To simplify the customization of the chart display, the map settings
are now re-organized in modes allowing the user to choose the preferred setting. Pre-
programmed settings are user selectable from Full, Medium, Low, Radar, Tides,
Custom. The default setting is Custom.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Display Mode" + 'ENTER'
The table below shows the selections for each mode:
Setting Full Medium Low Radar Tides Custom
(Default values)
Names On On On On On On
Buoys Name On Off Off Off Off On
Nav-Aids On On On On Off On
Light Sectors On Off Off Off Off On
Attention Areas On On Off Off Off On
Tides & Currents On Off Off Off On On
Seabed Type On Off Off Off Off On
Ports & Services On On Off On Off On
Tracks & Routes On Off Off Off Off On
Underwater Objects On On Off Off Off On
Depth Range On On On Off On On
Depth Range Min 3 Mt 3 Mt 3 Mt 3 Mt 3 Mt 3 Mt
Depth Range Max 10 Mt 10 Mt 10 Mt 10 Mt 10 Mt 10 Mt
Rocks > 0 Mt 0 Mt 0 Mt 0 Mt 0 Mt 0 Mt
Rocks < 9999Mt 5 Mt 5 Mt 5 Mt 5 Mt 9999Mt
Land Elevation Data On Off Off Off Off On
Roads On Off Off Off Off On
POIs On Off Off Off Off On
Lat/Lon Grid On Off Off Off Off On
Chart Boundaries On Auto Off Off Off Auto
Mixing Levels On Off Off Off Off Off
Value Added Data On Off Off Off Off On
Names: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Names" + 'ENTER'
Buoys Name: On/Off. The default setting is On. To identify better the Buoys, the
name/number of the buoys is shown next to the icon on the chart.
43
User Manual
Fig. 3.5.1.10 - Buoy Name
On the left side of the previous figure the two buoys have their name shown on the
right side. On the right side of the previous figure, the two buoys do not show the
name.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Buoys ID" + 'ENTER'
Nav-Aids: On/Off. The default setting is On. When selected it affects Lights, Sig-
nals, Buoys & Beacons display.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Nav-Aids" + 'ENTER'
Light Sectors: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+"Light Sectors" + 'ENTER'
Attention Areas: On/Off. The default setting is On. The Attention Areas will al-
ways be contour only when On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Attention Areas" + 'ENTER'
Tides & Currents: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Tides & Currents" + 'ENTER'
Seabed Type: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+"Seabed Type" + 'ENTER'
Ports & Services: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+"Ports & Services" + 'ENTER'
44 User Manual
Tracks & Routes: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Tracks & Routes" + 'ENTER'
Underwater Objects: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Underwater Objects" + 'ENTER'
Depth Range: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+"Depth Range" + 'ENTER'
Depth Range Min: Sets a min reference depth value. The default setting is 3 Mt.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Depth Range Min" + 'ENTER'
Depth Range Max: Sets a max reference depth value. The default setting is 10 Mt.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+"Depth Range Max" + 'ENTER'
Rocks >: Sets a min reference rocks value.
'MENU' + "MAP SETTINGS" +'ENTER'+ "Other Map Configurations" + 'ENTER'
+ "Rocks >" + 'ENTER'
Rocks <: Sets a max reference rocks value.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Rocks <" + 'ENTER'
Land Elevation Values: the Land Elevation areas are always shown, but it is pos-
sible to set On/Off the Land Elevation display. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Lan Elevation Values" + 'ENTER'
Roads: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Roads" + 'ENTER'
POIs (Points Of Information): On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "POIs" + 'ENTER'
Lat/Lon Grid: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Lat/Lon Grid" + 'ENTER'
45
User Manual
Chart Boundaries: On/Off/Auto. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Chart Boundaries" + 'ENTER'
Value Added Data: On/Off. The default setting is On.
'MENU' + "MAP SETTINGS" +'ENTER' + "Other Map Configurations" + 'ENTER'
+ "Value Added data" + 'ENTER'
3.5.2 GETTING AUTOMATIC INFO
The type of Automatic Info is user selectable.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER' +"AUTO
INFO" + 'ENTER'
The possible settings are:
- Off: disabled, no automatic info shown at all.
- On Points: only on points. This is the default setting.
- On All: on all objects (points, lines and areas).
The Automatic Info On Points shows information when the cursor is placed
on points (as Port Services, Tides, lights, wrecks, rocks, buoys, beacons, obstruc-
tions, land markers, etc.). The Automatic Info On All shows information when the
cursor is placed on points, on lines (as Depth contours, Traffic Separation, Territo-
rial Sea, Cartographic Lines etc.) on areas (Depth, Built-up, Sea, Attention, Restricted
etc.) and on names (on the beginning of the text -hot spot- or on any of the characters
of the name -name message box-).
The details on Land, Source of Data, Cartographic Area and Spot Soundings
are not shown.
Fig. 3.5.2 - Automatic Info on Points window
If you press 'ENTER' all available information about the cartographic point
under the cursor will be shown.
46 User Manual
3.5.2.1 Info on objects with Pictures
On the Quick Info, there will be the camera icon on the top bar of the window if at
least one of the objects found has one or more pictures associated.
Fig. 3.5.2.1 - Example of Quick Info on objects with picture
On the Full Info, there will be the small camera icon on a corner of the square
containing the object icon or a big photo icon centered on the square for the object
without icon.
Fig. 3.5.2.1a - Example of Full Info on objects with picture
To see the picture press 'ENTER' when the object with a picture is highlighted.
Change Picture Size
When the picture is shown, it is possible to fit it to screen by pressing 'ENTER'.
3.5.3 INFO TREE AND EXPANDED INFO PAGE
This page combines the Info Tree and the Expanded Info pages; this gives the
advantage of showing the details of the object selected on the Info Tree while the
cursor is moving through the Info Tree’s items.
The upper side of the page contains the Info Tree and the Lower side contains
the expanded information. While moving the cursor through the Info Tree, all the rel-
evant information of the selected object is shown on the lower part of the page.When
the selected object is a Tide Height, pressing 'ENTER' the Tide page is shown.
Pressing 'CLEAR' the page is closed. If the information shown exceeds the
page size, the user may scroll the page.
47
User Manual
3.5.4 INFO FUNCTION
Place the cursor in any place you want and press:
'MENU' + "INFO" + 'ENTER'
to show the Info Tree and Expanded Info page (see Par. 3.5.4).
3.5.5 GETTING PORT INFO
Upon viewing the chart of a port or harbour, you will see a Port Info icon
that can be clicked on to query the available information immediately displayed
with many details. The Port Info icon is visible only if the Ports & Services option is
On (default setting).
Fig. 3.5.5 - Port Info icon
The available information is shown in the Automatic Info window where
icons of the available services are shown:
Fig. 3.5.5a - Automatic Info window
To expand information about that object press 'ENTER'.
3.5.6 GETTING TIDE INFO
When you will see a Tide Info icon you can click on it to query the available
information that will immediately be displayed.
48 User Manual
Fig. 3.5.6 - Tide Info icon
Place the cursor on the Tide symbol, a Automatic Info window is opened:
Fig. 3.5.6a - Automatic Info on Tide
To display the Tide Graph page, press 'ENTER' for two times.
Fig. 3.5.6b - Tide Graph
Using the cursor key, it is possible to move the cursor anywhere on the
graph and display the time, height (vertical cursor) and draught (horizontal cursor)
on a particular graph point. Also use 'ZOOM IN' or 'ZOOM OUT' to go to previ-
ous or next day and 'ENTER' to set date (move the cursor key up/down to insert
the desired number and use it left/right to move cursor to left/right).
49
User Manual
Note
Tide graphs are an approximation of the Tide and they should be used in conjunction with
traditional Tide tables and navigational methods.
3.5.7 FIND FUNCTION
The chartplotter allows finding Nearest Services, Port By name, Tide Sta-
tions, Wrecks and Obstructions.
3.5.7.1 Finding Nearest Services
To locate and display the nearest available facilities of a particular type (i.e.
the nearest Hospital, sailmaker, bank, etc.).
'MENU' + "FIND" + 'ENTER' + "NEAREST SERVICES" + 'ENTER'
The icons of the available services are shown. Use the cursor key to select
any facility and press 'ENTER'. The list of the nearest ports (up to 10) containing
the facility will be shown on the screen. Then choose the port you want and press
'ENTER'.
3.5.7.2 Find Port
To show the list of all ports stored on the C-CARD and to locate them on
the map follow the procedure:
'MENU' +"FIND" + 'ENTER' + "PORT BY NAME" + 'ENTER'
Note
A Warning message is shown if there is no C-CARD inserted or there are no ports on the C-
CARD.
Searching by name
'MENU' +"FIND" + 'ENTER' + "PORT BY NAME" + 'ENTER' + "SEARCH
PORTS" + 'ENTER'
The list sorted by name of all available ports is shown if the Range option is disabled
(selected Off); otherwise the list of available ports in the range is shown. Press 'MENU'
and then use the cursor key to insert the port name (max 15 characters). Press 'EN-
TER' to confirm the inserted name (press 'CLEAR' to close the menu). If the in-
serted name is found, the list of all ports which name has the inserted name appears
on the screen. Repeat the operation to refine search or move through the list with
cursor key. Press 'ENTER' to locate the port on the map.
Searching port into selected range
'MENU' +"FIND" + 'ENTER' + "PORT BY NAME" + 'ENTER' + "RANGE" +
'ENTER'
50 User Manual
Allows to locate the port into a selected range. Using the cursor key to insert the
preferred value. Press 'ENTER' to confirm.
3.5.7.3 Finding Tide Stations
Finds the nearest Tide Stations (up to 10) on the map, from the boat position
- if a valid fix is received - or from the cursor position - if the received fix position is
not good.
'MENU' +"FIND" + 'ENTER" + "TIDE STATIONS" + 'ENTER'
After a few seconds a window appears. Choose the Tide Station you want
and press 'ENTER' to display the Tide Graph page (see Par. 3.5.7). Press 'CLEAR'
to display the Tide Station chosen.
3.5.7.4 Finding Wrecks
Searches for Nearest Wrecks:
'MENU' +"FIND" + 'ENTER' + "WRECKS" + 'ENTER'
Use the cursor key to select the port and 'ZOOM IN'/'ZOOM OUT' to select
next/previous page. Press 'ENTER' to locate the selected Wreck on the map.
3.5.7.5 Finding Obstructions
Searches for Nearest Obstructions:
'MENU' +"FIND" + 'ENTER' + "OBSTRUCTIONS" + 'ENTER'
Use the cursor key to select the port and 'ZOOM IN'/'ZOOM OUT' to select
next/previous page. Press 'ENTER' to locate the selected Obstruction on the map.
3.6 MAN OVERBOARD (MOB)
It is an important function useful in the case someone or something falls
overboard.
3.6.1 INSERTING MOB
Press 'MOB' to place MOB symbol at ship's coordinates. On the screen the
MOB symbol and a window to advise tha the MOB is activated appear, press 'CLEAR'
to delete this window. Data displayed in Text Area are related to MOB. Placing the
cursor on the MOB symbol an information window appears:
51
User Manual
Fig. 3.6.1 - Man Overboard
Note
In the information window the bottom side "ENTER for Options" appears only if the "Advanced
Functions" item in the "Basic Settings" menu is activated (On), see Par. 3.2.4.
3.6.2 DELETING MOB
Press 'MOB', select 'CANCEL" and press 'ENTER' again. The MOB sym-
bol remains on the screen shaded until the next screen redraws.
Note
If the "Advanced Settings" item in the menu "Basic Settings" is activated (On), see Par. 3.2.4,
placing the cursor on MOB the information window appears as shown in the previous Fig. 3.6.1.
Press 'ENTER', select "CANCEL" and press 'ENTER' again: the MOB symbol remains on the
screen shaded until the next screen redraws.
52 User Manual
53
User Manual
4
For the Experienced User
Now you have had a chance to became familiar with your new chartplotter,
there are a great number of advanced features that you will find helpful. First of all
the use of the Advanced Mode.
The chartplotter can operate in two different modes: Basic Mode and Ad-
vanced Mode. In the first mode there is a restricted number of functions, while in
Advanced Mode it is possible to have more available functions, for example it is
possible to handle Waypoints. To select the Advanced Mode:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "ADVANCED FUNCTIONS" +
'ENTER' + "ON" + 'ENTER'
When Advanced Functions is Off the chartplotter operates in Basic Mode.
4.1 MORE ABOUT CREATING AND USING ROUTES
At anytime, you may add or delete Waypoints, see a route summary, reverse
the direction of the route or erase the entire route.
4.1.1 WAYPOINT
You may add Waypoints, delete Waypoints from a route, move any Waypoint
in the route to another location, insert a Waypoint between two existing ones, find any
Waypoint at anytime. Every time you place the cursor on a Waypoint the following
functions are available.
4.1.1.1 Adding Waypoint
Select Advanced Mode + 'ENTER' + "WAYPOINT" + 'ENTER'
The Waypoint appears on the cursor position. An info window is shown
containing route number, Waypoint name, symbol and Latitude/Longitude.
54 User Manual
Fig. 4.1.1.1 - Waypoint placing
4.1.1.2 Creating a route
Repeat the "Adding Waypoint" procedure described in the previous Par.
4.1.1.1. The sequence of moving the cursor and pressing 'ENTER' is continued to
create the route, until you have reached the last Waypoint, your final destination.
Segments connecting the Waypoints are shown, and the starting point is identified
by a circle surrounding the first Waypoint of the route:
Fig. 4.1.1.2 - Route planning
4.1.1.3 Deleting Waypoint
Select Advanced Mode + Place cursor on Waypoint
Fig. 4.1.1.3 - Deleting Waypoint (I)
55
User Manual
Press 'ENTER'. Select "DELETE" and press 'ENTER'. The Waypoint is
deleted and a new line between previous and next Waypoint is shown. The deleted
Waypoint remains shaded until the screen is redrawn.
Fig. 4.1.1.3a - Deleting Waypoint (II)
4.1.1.4 Deleting route
Select Advanced Mode + Place cursor on Waypoint
Press 'ENTER'. Select "DELETE ROUTE" and press 'ENTER'. A window
is opened: select "YES" and press 'ENTER' to confirm (select "NO" and press 'ENTER'
otherwise). The route remains on the screen shaded until the screen is redrawn. To
delete route see also Par. 4.1.2.2 and 4.1.2.5.
4.1.1.5 Distance and Bearing to Target
Once you have positioned the cursor on the desired starting Waypoint (it
could be the first Waypoint of the route or another one) press 'GO-TO'. A circle
surrounds the Waypoint symbol. A line is shown, connecting the Target with the
ship's position. When the Target is placed, all navigation data are referred to this
Target.
Fig. 4.1.1.5 - Selecting destination (Target)
The destination will automatically switch to the next Waypoint on the route
when you reach or pass the present destination.
56 User Manual
Time To Go
When the Target is set the TTG value is displayed in the Graphic Data page (or in
the Navigation Data page):
'PAGE' more times
Note
If SOG value is less than 1.0 knots or the BRG is greater than 90 degrees, the TTg value is not
displayed.
Deleting Target
If in Basic Mode place cursor on Target icon and press 'CLEAR': the symbol that
identifies Target disappears from the screen, but the Waypoint remains.
If in Advanced Mode (see Par. 3.4.3) place cursor on Target icon, press 'ENTER',
select "STOP NAV" and press 'ENTER': the symbol that identifies Target disap-
pears from the screen, but the Waypoint remains.
Note
If you select "NEXT"/"PREV" and press 'ENTER', the Target icon is moved on the next/
previous Waypoint in the route.
Otherwise in both Modes (when the cursor is placed in a generic position on the
chart) press 'GO-TO'. A window appears to advice that the Destinetion point is
present: select "STOP" and press 'ENTER', the symbol that identifies Target disap-
pears from the screen, but the Waypoint remains.
Note
If you select "START" and press 'ENTER', the Target icon is moved on the new cursor position.
4.1.1.6 Moving Waypoint
Select Advanced Mode + Place cursor on Waypoint
Press 'ENTER'. Select "MOVE" and press 'ENTER'. Use the cursor key to
move the cursor: a dotted line, connecting the Waypoint to the new position, is
shown:
Fig. 4.1.1.6 - Moving Waypoint function (I)
57
User Manual
To place the Waypoint in the new position, choose the new place and press
'ENTER' ('CLEAR' otherwise), Waypoint appears in the new position:
Fig. 4.1.1.6a - Moving Waypoint function (II)
4.1.1.7 Inserting Waypoint
Every time you place the cursor on the segment connecting two existing
Waypoints of a route the following function is available.
Place cursor on route leg
Fig. 4.1.1.7 - Placing Waypoint between two existing ones (I)
Press 'ENTER'. Select "INSERT" and press 'ENTER'. The line between the
two Waypoints is turned into a dotted line: move the cursor to the new position.
When the cursor is stationary for one second or two, the line will "rubber-band",
drawing a dotted line between the last Waypoint and the cursor, and another dotted
line between the cursor and the next Waypoint:
58 User Manual
Fig. 4.1.1.7a - Placing Waypoint between two existing ones (II)
Once you have positioned the cursor at new location, press 'ENTER' (press
'CLEAR' to abort operation):
Fig. 4.1.1.7b - Placing Waypoint between two existing ones (III)
4.1.1.8 Editing Waypoint
Select Advanced Mode + Place cursor on Waypoint
Press 'ENTER'. Select "EDIT" and press 'ENTER' to modify a Waypoint.
A window will be shown with Name, Symbol and Latitude/Longitude of the
Waypoint, advising about what Waypoint data are modifiable.
Fig. 4.1.1.8 - Edit Waypoint (I)
Use the cursor key to select the field. If you have selected Name field, press
59
User Manual
'ENTER': use the cursor key to insert the character (8 characters max), then press
'ENTER'. If Symbol field is selected press 'ENTER': a window with 16 different
symbols appears:
Fig. 4.1.1.8a - Edit Waypoint (II): Waypoint symbols
Use the cursor key to select the symbol and press 'ENTER'. If select
Coordinates field, press 'ENTER' and then use the cursor key to insert the
value. Then press 'CLEAR'.
Note FOR COLOR CHARTPLOTTER
If Color field is selected press 'ENTER': a window with 8 different colors appears, use the cursor
key to select the desired color and press 'ENTER'.
Fig. 4.1.1.8b - Edit Waypoint (III)
4.1.1.9 Finding information about Waypoints: User Points List page
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER'
Move up/down the cursor key to select the User Point you wish. If the page
contains more than 8 User Points, the list continues in the next pages.
Finding User Points
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER' +
"FIND' + 'ENTER'
The chartplotter exits from the User Points List page and redraws the chart. The
selected point appears, with the cursor placed on it.
60 User Manual
Deleting selected User Point
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER' +
"CLR-ONE' + 'ENTER'
Deletes the selected User Point. A warning message appears, select "YES" and press
'ENTER' ('CLEAR' otherwise).
Deleting all User Points with the same symbol
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER' +
"CLR-SYM' + 'ENTER'
Deletes all User Points which have the same identifier of that shown in the selected
row. A warning message appears, select "YES" and press 'ENTER' ('CLEAR' other-
wise).
Deleting all User Points with the same type
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER' +
"CLR-TYP' + 'ENTER'
Deletes all User Points which have the same type of that shown in the selected row.
A warning message appears, select "YES" and press 'ENTER' ('CLEAR' otherwise).
Deleting all stored User Points
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER' +
"CLR-ALL' + 'ENTER'
A warning message appears, select "YES" and press 'ENTER' ('CLEAR' otherwise)
to delete all stored User Points.
Send/Receive User Points
Sends all User Points to an external device using the serial port:
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER' +
"SEND"
Reads all User Points from NMEA Input port:
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER' +
"RECEIVE"
4.1.2 ROUTES
The following functions are used for the route management. The chartplotter
handles routes from 1-25, which are permanently stored in the memory as they are
created. Only one route can be selected for work at any one time.
4.1.2.1 Selecting Route
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"CURRENT ROUTE" + 'ENTER'
61
User Manual
A window appears with the route number list and the related route name.
Use the cursor key to scroll the list up/down. Pressing 'ENTER' the selected route
becames the current route.
Note
If there is the Target in the current route, it is not possible to change the current route. So if the
"Current Route" item is selected, a Warning window appears because Go-To is placed in the
current route.
4.1.2.2 Deleting route
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' + "DE-
LETE ROUTE" + 'ENTER'
A window is opened: select "YES" and press 'ENTER' to confirm (select "NO"
and press 'ENTER' otherwise). The route remains on the screen shaded until the screen
is redrawn. To delete route see also Par. 4.1.1.4 and 4.1.2.5).
4.1.2.3 Reversing route
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' + "RE-
VERSE ROUTE" + 'ENTER'
Reversing a route plan is most typically used to return to the point where the
route originally started.
Note FOR COLOR CHARTPLOTTER
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"ROUTE COLOR" + 'ENTER'
A window is opened: use the cursor keys to select the route color you want among the eight colors
available. Press 'ENTER' to confirm. The route appears on the screen colored by the selected color.
It is possible to select a different color for any route.
4.1.2.4 Finding information about a route: Route Report
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"ROUTE REPORT" + 'ENTER'
If there are more than 8 Waypoints shown, use the cursor key to select another
page.
Fig. 4.1.2.4 - Route Data Report page
62 User Manual
Selecting route
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"ROUTE REPORT" + 'ENTER' + "ROUTE #" + 'ENTER'
Use the cursor key to select the route number and press 'ENTER'. The route, shown
by straight segments, is centered on the screen, with the cursor on the central
Waypoint. See also Par. 4.1.2.1.
Note
If there is the Target in the current route, it is not possible to change the current route. So if the
"Route #" item is selected, the chart plotter emits three beeps.
Changing Speed & Fuel values
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"ROUTE REPORT" + 'ENTER'
It is possible to modify the Speed and Fuel consumption values, respectively by selecting
"SPEED" and "FUEL". Insert value by using the cursor key and pressing 'ENTER'.
Reversing route
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"ROUTE REPORT" + 'ENTER' + "REVERSE" + 'ENTER'
Reversing a route plan is most typically used to return to the point where the route
originally started. See also Par. 4.1.2.3.
Deleting route
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"ROUTE REPORT" + 'ENTER' + "CLEAR" + 'ENTER'
A window is opened: select "YES" and press 'ENTER' to confirm (select "NO" and
press 'ENTER' otherwise). The route remains on the screen shaded until the screen is
redrawn. To delete the route see also Par. 4.1.1.4 and 4.1.2.2.
4.1.2.5 Route Name
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"ROUTE NAME" + 'ENTER'
Use the cursor key to insert the route name (max 16 alphanumeric char.).
4.1.2.6 Send/Receive Route
To transmit the Active Route information onto the NMEA output port.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' + "SEND"
The NMEA WPL & RTE messages are sent to the output port.
To save Route information received from the NMEA input port.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ROUTE" + 'ENTER' +
"RECEIVE"
63
User Manual
The received route is saved on the Active route, overwriting it. The NMEA
WPL & RTE messages are sent to the input port.
4.2 USING MARKS & EVENTS
You may place a Mark, as it is called, at your cursor position, while Event is
created at your vessel position.
4.2.1 MARKS
You may tag a location on the chart with a Mark symbol and number, which you can
record for later use. Every time you place the cursor on a Mark the following functions are
available.
4.2.1.1 Adding Mark
Select Advanced Mode + 'ENTER' + "MARK" + 'ENTER'
The new Mark appears on your cursor position. An info window containing
Mark name, symbol and Latitude/Longitude is shown.
4.2.1.2 Deleting Mark
Select Advanced Mode + Place cursor on Mark
Press 'ENTER'. Select "DELETE" and press 'ENTER': the Mark remains
on the screen shaded until the next screen is redrawn.
Note
If you try to delete a Mark that belongs to many routes, the chart plotter emits three beeps and on
the screen a Warning message appears. If you want to delete the Mark, press 'ENTER'.
4.2.1.3 Goto
Place cursor on Mark
Press 'GO-TO': a circle encloses the Mark symbol. A straight line is shown
on the screen connecting the Target with the ship's position. When the Target is
placed, all navigation data are referred to this Target.
4.2.1.4 Moving Mark
Select Advanced Mode + Place cursor on Mark
Press 'ENTER'. Select "MOVE" and press 'ENTER'. By moving the cursor
with the cursor key, a dotted line connecting the Mark with the new position is
shown:
64 User Manual
Fig. 4.2.1.4 - Moving Mark function (I)
Press 'ENTER':
Fig. 4.2.1.4a - Moving Mark function (II)
The Mark is placed in the new position, the "old" Mark, remains on the
screen shaded until the screen is redrawn.
Note
If you try to move a Mark that belongs to many routes, the chart plotter emits three beeps and on
the screen a Warning message appears. If you want to move the Mark, press 'ENTER'.
4.2.1.5 Editing Mark
Select Advanced Mode + Place cursor on Mark
Press 'ENTER'. Select "EDIT" and press 'ENTER'. A window appears to
modify Name, Symbol and coordinates of the existing Mark.
65
User Manual
Fig. 4.2.1.5 - Edit Mark
Use the cursor key to select the field. If you have selected Name field, press
'ENTER': use the cursor key to insert the character (8 characters max), then press
'ENTER'. If Symbol field is selected press 'ENTER': a window with 16 different
symbols appears. Use the cursor key to select the symbol and press 'ENTER'. If
Coordinates field is selected, press 'ENTER' and then use the cursor key to insert the
value. Then press 'CLEAR'.
Note FOR COLOR CHARTPLOTTER
If Color field is selected press 'ENTER': a window with 8 different colors appears, use the cursor
key to select the desired color and press 'ENTER'.
4.2.1.6 Finding information about Marks: User Points List page
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER'
A full window is opened showing information about all stored User Points
(Marks, Events and Waypoints). Move up/down the cursor key to select the User
Point you wish. If the page contains more than 8 User Points, the list continues in
the next pages. See Par. 4.1.1.9.
4.2.1.7 Add to Route
Select Advanced Mode + Place cursor on Mark
Press 'ENTER'. Select "ADD TO ROUTE" and press 'ENTER': the se-
lected Mark is connected to the current route. The same Mark can be added in many
routes.
Note
An existing Mark can be connected to the current route in another mode too. Place cursor on
Mark, the information window related to the Mark appears, press 'CLEAR' to close the window
and then press 'ENTER', select the Waypoint option and press 'ENTER'. The Mark is connected
to the current route.
4.2.2 EVENTS
In Navigate mode you may place a location with an Event symbol and num-
66 User Manual
ber, directly on the ship's position. Move the cursor to exit from Navigate mode;
place the cursor on an Event to access the following functions.
4.2.2.1 Adding Event
Select Advanced Mode + 'MODE', then 'ENTER' + "EVENT" + 'ENTER'
An Event is placed directly on the ship's position.
4.2.2.2 Deleting Event
Place cursor on Event
Press 'ENTER'. Select "DELETE" and press 'ENTER': the Event remains
on the screen shaded until the next screen is redrawn.
Note
If you try to delete a Event that belongs to many routes, the chart plotter emits three beeps and
on the screen a Warning message appears. If you want to delete the Event, press 'ENTER'.
4.2.2.3 Goto
Place cursor on Event
Press 'GO-TO': a circle encloses the Event symbol. A straight line is shown
on the screen connecting the Target with the ship's position. When the Target is
placed, all navigation data are referred to this Target.
4.2.2.4 Editing Event
Place cursor on Event
Press 'ENTER'. Select "EDIT" and press 'ENTER'. A window appears to
modify Name, Symbol of the existing Event.
Fig. 4.2.2.4 - Edit Event
Use the cursor key to select the field. If you have selected Name field, press
'ENTER': use the cursor key to insert the character (8 characters max), then press
'ENTER'. If Symbol field is selected press 'ENTER': a window with 16 different
symbols appears. Use the cursor key to select the symbol and press 'ENTER'. Then
press 'CLEAR'.
67
User Manual
Note FOR COLOR CHARTPLOTTER
If Color field is selected press 'ENTER': a window with 8 different colors appears, use the cursor
key to select the desired color and press 'ENTER'.
4.2.2.5 Finding information about Events: User Points List page
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER POINTS" + 'ENTER'
A full window is opened showing information about all stored User Points
(Marks, Events and Waypoints). Move up/down the cursor key to select the User Point
you wish. If the page contains more than 8 User Points, the list continues in the next
pages. See Par. 4.1.1.9.
4.2.2.6 Add to Route
Place cursor on Event
Press 'ENTER'. Select "ADD TO ROUTE" and press 'ENTER': the se-
lected Event is connected to the current route. The same Event can be added in
many routes.
Note
An existing Event can be connected to the current route in another mode too. Place cursor on
Event, the information window related to the Event appears, press 'CLEAR' to close the window
and then press 'ENTER', select the Waypoint option and press 'ENTER'. The Event is connected
to the current route.
4.3 MORE ABOUT A-B-C-D FUNCTION
The A-B-C-D function, explained in the previous paragraph 3.3, if Advanced
Mode is selected, allows you not only to create the A, B, C, D points and to delete
them, but also to modify and move them.
4.3.1 INSERTING THE A-B-C-D POINTS
Place the cursor on the desired position and press 'ENTER'. On the screen
the Create window appears, by using the cursor key select "A-B-C-D" and press
'ENTER': the A point and an information window on A appear. Move the cursor,
press 'ENTER', select "A-B-C-D" and press 'ENTER' again: the B point appears,
connected to A with a straight segment; an information window on A-B segment
(distance (DST), bearing (BRG) and total distance from the first point) appears. Moving
the cursor, pressing 'ENTER', selecting "A-B-C-D" and pressing 'ENTER' places
the C and D points (see previous Fig. 3.3.1).
68 User Manual
4.3.2 DELETING THE A-B-C-D POINTS
When placing the cursor on the desired point (A, B, C or D) the information
window appears. Press 'ENTER', select "DELETE" and press 'ENTER' again: the
point is deleted. When the point is deleted, the cursor is placed on the previous
point, if existed. The labels of the next points are renamed.
4.3.3 DELETING THE A-B-C-D SEGMENT
When placing the cursor on the desired point (A, B, C or D) or on segment
between two points the information window appears. Press 'ENTER', select "DELETE
ALL" and press 'ENTER' again: all points and connecting segments are deleted.
4.3.4 MOVING THE A-B-C-D POINTS
When placing the cursor on the desired point (A, B, C or D) the information
window appears. Press 'ENTER', select "MOVE" and press 'ENTER': by the cursor
key move the cursor, on the screen a dotted line connecting the point to move with the
new position appears. By pressing 'ENTER' the point is placing in the new position.
4.3.5 INSERTING THE A-B-C-D POINTS
Placing cursor on the segment connecting two points, the information win-
dow appears. Select "INSERT" and press 'ENTER': by the cursor key move the
cursor, on the screen a dotted line appears. By pressing 'ENTER' the new point is
placing between the two existed points which are renamed.
4.3.6 NAVIGATING ON THE A-B-C-D POINTS
If fix received is good, place the cursor on the desired point A, B, C or D and
press 'GO-TO'. When ship reaches the Destination point, navigation follows the
next point (if exists). When Target is set, three options are available: STOP NAV,
NEXT and PREV.
4.4 USING THE TRACK FUNCTIONS
The chartplotter can be set up for recording your track as you move and for
plotting this track on the chart.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER'
69
User Manual
4.4.1 SELECTING ACTIVE TRACK
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "AC-
TIVE TRK" + 'ENTER'
Select the number of the active track. The default setting is 1.
4.4.2 ENABLING TRACK STORING
'MENU' + "CONFIGURAZIONI SPECIALI" + 'ENTER' + "TRACCIA" + 'ENTER'
+ "TRACCIA" + 'ENTER'
To enable (On) or disable (Off) the track storing. It is not possible to use the
track storing if you are not receiving a valid fix. The default setting is On.
4.4.3 DISPLAYING TRACK
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "VIS-
IBLE" + 'ENTER'
To enable (On) or disable (Off) the displaying of track. The default setting is
Off.
4.4.4 SELECTING TRACK LINE PATTERN
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "LINE
PATTERN" + 'ENTER'
Selects the desired line pattern for the selected track.
Note FOR COLOR CHARTPLOTTER
"LINE PATTERN" item is substitued by the "COLOR" item, to select the desired color among
the eight colors available for the selected track.
4.4.5 DELETING TRACK
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "DIS-
TANCE" + 'ENTER'
Deletes all track. After pressing 'ENTER' a warning window appears: select
"Yes" and press 'ENTER' to confirm (select "No" otherwise).
4.4.6 DELETING SELECTED TRACK
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' +
"DELETE SELECTION" + 'ENTER'
Deletes the track selected. After pressing 'ENTER' a window appears: press
'ENTER' to set the first point , then press 'ENTER' to set the second point. A
warning window appears: select "Yes" and press 'ENTER' to confirm the deletion
70 User Manual
(select "No" otherwise).
4.4.7 SELECTING TRACK MEMORIZING TYPE
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "STEP
UNIT" + 'ENTER'
Choose Distance (Dist) - the chartplotter can store a fix when the distance
from its last stored position is greater than a defined distance; Time - the chartplotter
can store a fix after a defined time; Auto - the software decides when storing a posi-
tion, on the basis of the straight or curved track. The default setting is Time.
4.4.8 SELECTING DISTANCE
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "DIS-
TANCE" + 'ENTER'
When the tracking function is On and the type of track storing is Distance,
you can store a fix when the distance from its last stored position is greater than a
defined distance. Choose in the range 0.01, 0.05, 0.1, 0.5, 1.0, 2.0, 5.0, 10.0 Nm (the
distance unit is selected by the user, see Cap. 5). The default setting is 0.01 Nm.
4.4.9 SELECTING TIME
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "TRACK" + 'ENTER' + "TIME"
+ 'ENTER'
When the tracking function is On and the type of track storing is Time, the
chartplotter can store a fix after a defined time. Choose among 1, 5, 10, 30 sec, 1, 5,
10 min. The default setting is 1 sec.
4.5 USER C-CARD MENU
The chartplotter allows to copy information to an User C-CARD. You can
also return the information to internal memory at a later time. This allows virtually
unlimited storage.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER C-CARD" + 'ENTER'
71
User Manual
Fig. 4.5 -User C-CARD Menu
4.5.1 SAVING FILE
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER C-CARD" + 'ENTER'
+ "SAVE" + 'ENTER'
A window is opened to insert the file name and the type of data to save:
Fig. 4.5.1 - Save File function (I)
Select the file name. At first a default name is shown: use the cursor key to
insert the name. Press 'ENTER'. Select the data type to save among "MARK",
"EVENT", "ROUTE" or "TRACK".
Note
When naming a file, you may have trouble finding a name that uniquely identifies the file's
contents. Dates, for example, are often used in filenames; however, they take up several characters,
leaving you with little flexibility. The secret is to find a compromise, a point where you can
combine a date with a word, creating a unique filename. The maximum length of the filename
is 8 characters. The characters may be numbers (0, ..., 9), letters (A, ..., Z) and spaces (for example
legal identifiers are "ABC", "AA", "12121212", "A B C", "1 A 1", and so on.
Press 'CLEAR'. On the screen appears:
72 User Manual
Fig. 4.5.1a - Save File function (II)
4.5.2 LOADING FILE
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER C-CARD" + 'ENTER'
+ "LOAD" + 'ENTER'
Before pressing 'ENTER', choose file name in the list shown on the screen
using the cursor key.
4.5.3 DELETING FILE
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER C-CARD" + 'ENTER'
+ "DELETE" + 'ENTER'
A warning window is shown, select "YES" and press 'ENTER' to confirm
deletion (select "NO" otherwise). This operation remove old or unnecessary files to
clean up your User C-CARD. Remember that this option permanently erases the
file.
4.5.4 FORMATTING USER C-CARD
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER C-CARD" + 'ENTER'
+ "FORMAT" + 'ENTER'
A warning window is shown, select "YES" and press 'ENTER' to con-
firm the formatting (select "NO" otherwise). The format of User C-CARD
must be done before using a new User C-CARD: this operation prepares the
User C-CARD to receive and store information.
4.5.5 CHANGING USER C-CARD
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "USER C-CARD" + 'ENTER'
+ "CHANGE" + 'ENTER'
Allows to change the User C-CARD.
73
User Manual
4.6 C-LINK
C-Link system is a feature which allows to sharing the same cartographic
data between two chart plotter units (CP) linked via serial I/O port.
In order to activate C-Link function, a “MAX data C-CARD” (called REGU-
LAR C-CARD) must be inserted into one of the two chart plotters and a special
MAX data C-CARD (called MIRROR C-CARD) must be inserted on the other
chart plotter.
The two MAX data C-CARDs must have the same code and revision. So, the
MIRROR C-CARD can be utilized only on a chart plotter linked to another chart
plotter provided with the equivalent REGULAR C-CARD.
It is important to point out that the two chart plotters must have the update
s/w versions that allow C-Link function.
4.6.1 HOW C-LINK SYSTEM WORKS
When the CP is powered up, it switches into the “Stand-Alone Mode”. In
this work mode, the CP unit periodically scans all the available C-CARD slots search-
ing for MIRROR C-CARDs.
When one or more MIRROR C-CARD is found (in one or both CPs) a
special connection is established between the CPs to abilitate the MIRROR C-CARDs.
If a regular C-CARD which has previously activated a MIRROR C-CARD is re-
moved, even the MIRROS card will be not read anymore on the other unit.
4.7 C-LINK NAVIGATION DATA TRANSFER
This function allows transferring C-Link navigation data (Route Name, Des-
tination ID & Position, Next Waypoint ID & Position, Total Route length, Fuel
Consumption Rate, ETA, TTG etc.) (Hereinafter “c-link navigation data”) between
two chart plotters linked through the C-Link system.
The chart plotters can be set to operate in two modes:
- MASTER mode (Primary Chart Plotter that sends data)
- SLAVE mode (Secondary Chart Plotter that receives data)
When the navigation is activated on the Master chart plotter, the C-Link
navigation data will be continuously sent to the Slave until the navigation is active.
If the Master is navigating to a Single Destination, the Slave will show the Destina-
tion position and activate the navigation to it.
74 User Manual
If the Master is navigating to a Route, the Slave will show the Route Leg composed
by the Destination and the Waypoint after the Destination (Next Waypoint) and
activate the navigation to it. Any variation to the current C-Link navigation data
will be transferred from the Master to the Slave. The Slave will be provided with a
few dedicated pages to show the C-Link navigation data received from the Master.
4.7.1 OPERATIONS
4.7.1.1 Introductive elements
It is important remark, once more, that this function does not transfer the
whole route but just the information relative to the navigation. Such information
will be removed from the Slave Chart Plotter as soon as the navigation is terminated.
C-Link navigation data is exchanged by using two NMEA-0183 C-MAP pro-
prietary sentences: $PCMPN,1 and $PCMPN,2.
When the navigation is activated on the Master, it starts outputting the C-Link
navigation data. If the Slave is connected, all c-link navigation data received are stored
in its memory and the navigation is started.
The information sent by the Master consists of the following values:
- Navigation mode (To Single Destination / to a Route )
- Route Name (*)
- Destination ID
- Destination Position
- Next Waypoint ID (*)
- Range from Destination to next Waypoint (*)
- Bearing from Destination to next Waypoint (*)
- Route Length (*)
- Distance from Destination to Last Route Waypoint (*)
- Remaining Route Legs (*)
- Planned Cruising Speed
- Average Fuel Consumption
- Initial Fuel Load
C-Link navigation datacan refer to:
- Single Destination navigation
- Route Following navigation.
Values identified by (*) are sent only for Route Following navigation.
The Destination Icon, Navigation leg (Fix Position to Destination), the Next
Waypoint Icon and all other relevant c-link navigation data will be shown on the
75
User Manual
Slave chart plotter. Any variation of the C-Link navigation data on the Master will
be communicated to the Slave so to keep data aligned on both devices.
4.7.1.2 C-Link serial connection
The two chart plotters should be connected via serial ports. Any of the avail-
able ports can be used, the software will recognize automatically the serial ports
used. A typical connection is as follows:
CP1 CP2
TX —————> RX
RX <————— TX
GND <————> GND
4.7.1.3 Master Chart Plotter
Operating mode
To select the Master mode (Primary Station) follow the procedure:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"C-LINK" + 'ENTER' + "Primary Station" + 'ENTER'
Master mode is the default factory setting. All regular chart plotters’ functions are
allowed. As soon as the Destination is placed, the master chart plotter will start
transmitting all C-Link navigation data,
In Master mode the C-Link navigation data received from the NMEA port is ig-
nored. So, if the two chart plotters are both operating in Master mode, the C-Link
navigation data sent by the other chart plotter never processed.
Under such condition if the navigation is activated on one of the two chart plotters,
a warning message will be shown to notify that the C-Link navigation data will be
ignored by the other chart plotter.
4.7.1.4 Slave Chart Plotter
Operating mode
To select the Slave mode (Secundary Station) follow the procedure:
'MENU' + "BASIC SETTINGS" + 'ENTER' + "INPUT/OUTPUT" + 'ENTER' +
"C-LINK" + 'ENTER' + "Secundary Station" + 'ENTER'
When Slave mode is set, the chart plotter cannot manipulate the C-Link navigation
data anymore.
Stop current navigation
If the navigation was already active, it will be disabled as soon as Slave mode is set.
76 User Manual
An appropriate warning message will be shown to notify that the Navigation is
already active and to confirm whether Slave mode can be set.
Inhibit Navigation operation
As soon as Slave mode is set, the destination cannot be placed anymore either the
C-Link navigation data is received from the Master or not. Also, when the C-Link
navigation data is received from the Master, it will not be allowed to deactivate the
Navigation.
Inhibit Route following
While navigating to the route received from the Master the destination is reached
(either applying distance or perpendicular criteria), the destination will not be moved
to the next Waypoint on the route.
MOB handling
If the Navigation to the external destination is active and the the MOB key is pressed
on the Slave Chart Plotter, the MOB is placed but the navigation to the MOB is not
activated.
Notes
While navigating to the external destination the Operating Mode is switched to Master
mode, the navigation to the external destination will be terminated. An appropriate
warning message will be shown to notify that the Navigation to the external destina-
tion is active and to confirm whether Slave mode can be set. Setting Slave mode,
the C-Link navigation data will be deleted.
The C-Link navigation data are deleted at Power Off.
4.7.1.5 C-Link navigation data: Acquisition and Display
As soon as the C-link navigation data is received, the Slave parses the infor-
mation received and executes the relative actions depending on its current working
status.
Important
When the Navigation to the external Destination is activated, the Slave Chart Plotter will show
all relevant c-link navigation data exactly like when the destination is not the external one:
(Destination Name, DST and BRG to Destination, calculate XTE, calculate TTG etc). These
values will be displayed all places where required and they will be used to format NMEA-0183
output data.
77
User Manual
4.7.1.6 Graphical representation on Map Display
Fig. 4.7.1.6 - Graphical Displaying
4.7.1.7 Route Data Report
When the Navigation to the External Route is received, it will be possible to
display the information related to the External Route by entering the Route Data
Report.
Fig. 4.7.1.7 - External route on Route Data Report
- External Route : Name of the External Route (from PCMPN,0)
- Cruising Speed : Planned Cruising Speed (from PCMPN,1)
- Fuel Consumption Rate : Planned Fuel Consumption Rate (from PCMPN,1)
- Total Route length Route: Length from First to Last Wpt. (from PCMPN,1)
- Initial Fuel Load : Volume of Fuel available before the navigation was
started (Liters)
- Total Fuel Consumption : Calculated Fuel consumption to navigate the whole
route.
- Waypoints in Route : No. of Wpts in the Route (from PCMPN,1)
- Remaining Waypoints : No. of Wpts from Dest to Last Wpt (from PCMPN,1)
- Distance to Destination : Distance from Ship to Destination (Calculated)
78 User Manual
- Distance to Next Wpt : Distance to travel from ship to the Wpt after the Des-
tination (calculated: Distance to Dest + Next
Route Leg length)
- Distance to Last Wpt : Distance to travel from ship to the End of the Route
(Calculated: Distance to Dest +Distance From Dest
to last Wpt received from PCMPN,1)
- TTG To Destination : Estimated Time to travel the “Distance to Last Wptt”.
Calculated using Cruising Speed.
- TTG To Next Wpt : Estimated Time to travel the “Distance to Next
Waypoint” Calculated using Cruising Speed.
- TTG to Last Wpt : Estimated Time to travel the “Distance to Last Wpt”.
Calculated using Cruising Speed
- ETA to Destination : Estimate Time of Arrival to the Destination Point.
Calculated: Current Time + “TTG To Destination”
- ETA to Next Waypoint : Estimate Time of Arrival to the Waypoint after the
Destination. Calculated: Current Time + “TTG To
Next Waypoint”
- ETA to Last Wpt : Estimate Time of Arrival to the End of the Route.
Calculated: Current Time + “TTG To Last Wpt”
4.7.1.8 Quick Info
Route Navigation: Quick Info on the Destination
Fig. 4.7.1.8 - Quick Info on Destination
Quick info on Single Destination
Fig. 4.7.1.8a - Quick Info on Single Destination
79
User Manual
5
Advanced Settings
The Advanced Settings menu allows the user to control the advanced func-
tions of the chartplotter. The functions are organized into menus. For example all
options related to the Fix are in a menu called Fix. For menus there is not an
explaniation because they are in the previous Chapters, so for the Map Setting menu
see Par. 3.5, for the Track menu see Par. 4.4, for the Route menu see Par. 4.1.2, for
the User Points menu see Par. 4.1.1.9 and for the User C-CARD menu see Par. 4.5.
'MENU' + "ADVANCED SETTINGS" + 'ENTER'
Once you are in the Advanced Setting menu, use your cursor key to highlight
the item and press 'ENTER' to activate or to proceed to the next selection menu.
5.1 SETUP
The Setup menu allows to enable or disable the general options for handling
of the chartplotter. For the Auto Info option see par. 3.5.3.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER'
5.1.1 TIME REFERENCE
Sets UTC or Local Time. The default setting is UTC.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER' + "TIME
REFERENCE" + 'ENTER'
5.1.2 TIME FORMAT
Sets you preferred time between 12 hour and 24 hour. The default setting is 24
hours.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER' + "TIME
FORMAT" + 'ENTER'
80 User Manual
5.1.3 DATE FORMAT
Sets you preferred date between MM-DD-YY (month-day-year) and DD-
MM-YY (day-month-year). The default setting is MM-DD-YY.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER' + "DATE
FORMAT" + 'ENTER'
5.1.4 WIND SPEED
Selects the Wind Speed unit amang Kts = Knots, m/s and Kmh =
kilometers per hour. The default setting is Kts.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER' + "WIND
SPEED" + 'ENTER'
5.1.5 BEEPER
Turns On/Off the sound after pressing a key ("beep"). The default setting is On.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER' +
"BEEPER" + 'ENTER'
5.1.6 EXTERN WAYPOINT
The coordinates of a Waypoint, received from a GPS connected to the
chartplotter, can be stored into the chartplotter, if the GPS is NMEA-0183 protocol
compatible and support the $BWC sentence (this symbol remains on the screen for
30 seconds). You may save it by placing a Waypoint or a Mark onto that symbol. As
soon as the chartplotter receives another $BWC sentence with the coordinates of a
new Waypoint, the symbol moves to the new point. The default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER' + "EX-
TERN WPT" + 'ENTER'
5.1.7 BACKLIGHT TIMEOUT
Disables (Off) or sets the desired value (among 1, 3, 5, 10 minutes) for the
backlight timeout of the chartplotter. The default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SETUP" + 'ENTER' + "B.
LIGHT TIMEOUT" + 'ENTER'
5.2 FIX
The Fix menu allows to handle the functions related to the fix.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER'
81
User Manual
5.2.1 FIX CORRECTION
Turns On/Off the Correction from the positioning system. If the new Cor-
rection is calculated, but the Correction is not enabled, the ship's position is not
changed. The default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "FIX COR-
RECTION" + 'ENTER'
5.2.2 COMPUTE CORRECTION
Corrects fixes from the positioning instrument. By placing the cursor on the
ship's real position and selecting this option, the error is calculated and internally
memorized for appropriate correction, but not applied.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "COM-
PUTE CORRECTION" + 'ENTER'
5.2.3 CORRECTION OFFSET
Manual correction of fix position.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "COR-
RECTION OFFSET" + 'ENTER'
A window with the cursor coordinates appears: insert the preferred value
and press 'ENTER'.
5.2.4 POSITION FILTER
Turns On/Off the Position Filter. In case of a jittering fix this option makes
the ship' position more stable and the track smoother. The default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "POSI-
TION FILTER" + 'ENTER'
5.2.5 SPEED FILTER
Turns On/Off the Speed Filter. When it is On, you can filter the speed of
the ship, to optimize it. The default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "SPEED
FILTER" + 'ENTER'
5.2.6 FILTER DUMP
Inserts the value for the Filter Dump in the range [500 - 12000]. The
default setting is 500.
82 User Manual
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "FILTER
DUMP" + 'ENTER'
5.2.7 DEAD RECKONING
Enables (On) or disables (Off) the Dead Reckoning. The default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "DEAD
RECKONING" + 'ENTER'
5.2.8 STATIC NAVIGATION
Sets up a threshold for the speed. When the speed received from the position-
ing device is under that threshold, the chartplotter displays zero speed. The default
value is 0.0 Knots.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "FIX" + 'ENTER' + "STATIC
NAVIGATION" + 'ENTER'
5.3 NAVIGATE
The Navigate menu allows to handle the functions related to navigation.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER'
5.3.1 COORDINATE SYSTEM
Sets your preferred Coordinate System among ddd mm ss, ddd mm.mm,
ddd mm.mmm, UTM, OSGB, TD. The default setting is ddd mm.mmm.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' +
"COORDINATE SYSTEM" + 'ENTER'
If TD is selected on the screen a new menu appears:
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' +
"COORDINATE SYSTEM" + 'ENTER' + "TD" + 'ENTER'
Chain: Selects the preferred chain. The default setting is 9970.
Pair: Selects the pair of stations in the selected chain. The default setting is W X.
ASF 1/2: Sets the ASF (Additional Second Factor) for the slave in the selected chain.
The default setting is 0.
Alter: Turns On/Off the Alternate Solution in the chain. The default setting is Off.
5.3.2 FIX DATUM
Selects the Fix Datum among 130 items. WGS-84 is the default Fix Datum.
83
User Manual
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' +
"FIX DATUM" + 'ENTER'
5.3.3 MAP DATUM
Selects the Map Datum among 130 items. WGS-84 is the default Fix Datum.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' +
"MAP DATUM" + 'ENTER'
5.3.4 MAP ORIENTATION AND RESOLUTION
Selects the orientation of your chart according to your personal needs (see
Par. 3.5.1.3 for more information). The Orientation Resolution is the resolution
angle for the Map Orientation, range [5, 60] degrees. The default setting is 30°.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' +
"ORIENT. RESOLUTION" + 'ENTER'
5.3.5 ROLLING ROAD SCALE
Sets you preferred Rolling Road Scale among 0.2, 0.5, 1.0, 2.0, 4.0, 10.0. The
default setting is 0.2.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' +
"ROLL ROAD SCALE" + 'ENTER'
5.3.6 RESET TOTAL AND PARTIAL TRIP
Resets the partial or total distance traveled by the ship from the first activa-
tion of the chartplotter or starting from the values reset. The partial or total trip
value is shown on the top of the Navigation Page.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' +
"RESET PARTIAL TRIP" + 'ENTER'
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "NAVIGATE" + 'ENTER' +
"RESET TOTAL TRIP" + 'ENTER'
5.4 COMPASS
The Compass menu sets the desired value for Bearing and Magnetic Varia-
tion, and selects the Compass Calibration page.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "COMPASS" + 'ENTER'
84 User Manual
5.4.1 BEARINGS
Selects either degrees magnetic or true. If magnetic readings are selected the
variation is computed automatically for every zone as soon as the chart is displayed.
The default setting is Mag.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "COMPASS" + 'ENTER' +
"BEARINGS" + 'ENTER'
5.4.2 VARIATION
It is possible to calculate the Magnetic Variation in an Automatic or manual
mode, by inserting the step for calculation of Magnetic Variation. The default set-
ting is Automatic.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "COMPASS" + 'ENTER' +
"VARIATION" + 'ENTER'
5.4.3 CALIBRATION
The variation table is used to match magnetic value readout on the chartplotter
comparable with the value given by the compass of the boat. In other words, since
the compass of the boat must be compensated (due to the iron masses, ...), we use the
same values given by the chartplotter. This means that, for example, if the BRG to
the next Waypoint readout in the chartplotter display is "X" Mag degree, if you steer
the boat reading "X" Mag degree from the compass, you are driving well toward the
next Waypoint.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "COMPASS" + 'ENTER' +
"CALIBRATION" + 'ENTER'
5.5 ALARMS
The chartplotter provides alarm settings for various functions. Here you can
set the system for your navigational requirements.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER'
5.5.1 ARRIVAL ALARM
Specifies the radius of a circle around the Waypoint of a route: when your
vessel reaches this circle the alarm sounds. You can disable (Off) the Arrival Alarm
or insert value. The default setting is 1.00 Nm.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER' + "AR-
RIVAL ALARM" + 'ENTER'
85
User Manual
5.5.2 XTE ALARM
Disables the XTE Alarm (Off) or selects the desired value. The default setting is
Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER' + "XTE
ALARM" + 'ENTER'
5.5.3 ANCHOR ALARM
This function allows inserting of the limit of anchor dragging: beyond that,
the alarm is activated. The chartplotter computes the distance between the current
GPS position and the GPS position saved at the activation of the anchor alarm in the
menu. If the computed distance exceeds the value set in the menu, the chartplotter
shows the alarm message and starts the acoustic alarm. The default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER' + "AN-
CHOR ALARM" + 'ENTER'
5.5.4 DEPTH ALARM
Specifies the depth or disables the Depth Alarm.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER' +
"DEPTH ALARM" + 'ENTER'
5.5.5 GROUNDING ALARM
The chartplotter is provided with a function that, by querying the map's data,
verifies potential danger to navigation due to shallow water, land, rocks, obstructions
and shoreline constructions. The maps are scanned periodically (every 10 seconds).
When the Grounding Alarm is active, the chartplotter scans an area in front
of the boat. This area is identified by a triangle drawn in front of the boat icon whose
direction is determined by the current boat heading. The length of the triangle is
user selectable and its angle is 30 degrees. If any of the above objects are found, the
chartplotter notifies the danger on a dedicated warning message box in the Ground-
ing Alarm Report page.
The Grounding Alarm is switched Off by default after a Master Reset. Once
the Grounding Alarm has been activated, a warning message is shown.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER' +
"GROUNDING ALARM" + 'ENTER'
Note
The Grounding Alarm function only operates with the new C-CARDs. It also affects the speed
of the redraw of the screen. If this function is not used it maybe disabled.
86 User Manual
5.5.6 GROUNDING ALARM RANGE
Allows setting the length of the sector to be detected among 0.25, 0.5, 1.0 Nm.
The default setting is 0.25 Nm. When any of the searched objects is found in the scanned
area, a tick marker is printed on the relative box in the Grounding Alarm Report page to
identify which dangerous objects have been currently detected.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER' +
"GROUNDING ALARM RANGE" + 'ENTER'
5.5.7 GROUNDING ALARM REPORT
Allows displaying the report of the dangerous objects currently detected.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "ALARMS" + 'ENTER' +
"GROUNDING ALARM REPORT" + 'ENTER'
5.6 SIMULATION MENU
The built-in Simulator function allows you to become proficient in the use
of the chartplotter. No current position fix is required because the chartplotter simu-
lates position data internally.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER'
5.6.1 SIMULATION MODE
Once the settings are selected, turn on the Simulator:
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER' +
"ACTIVATE SIMULATION" + 'ENTER'
To turn On the Simulation select Off. The default setting is Off.
5.6.2 SPEED
To start the simulator you can insert the Speed value. Using the cursor key
select the preferred Speed and press 'ENTER'. The default setting is 01.0 Kts.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER' +
"SPEED" + 'ENTER'
5.6.3 HEADING
To start the simulator you can insert the Heading value. Using the cursor
key select the preferred Heading and press 'ENTER'. The default setting is 000° M.
87
User Manual
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER' +
"HEADING" + 'ENTER'
5.6.4 DATE AND TIME
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER' +
"DATE" + 'ENTER'
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER' +
"TIME" + 'ENTER'
Using the cursor key insert the preferred Date and Time and press 'EN-
TER'.
5.6.5 CURSOR CONTROL
Enables (On)/disables (Off) the cursor control. The default setting is Off.
'MENU' + "ADVANCED SETTINGS" + 'ENTER' + "SIMULATION" + 'ENTER' +
"CURSOR CONTROL" + 'ENTER'
5.7 C-STAFF
The C-Staff functions are based on STAFF Concept ® (Satellite Tracking
Aided Fleet Fishing). The STAFF Concept ® is designed for professional fishing
purpose to allow monitoring the position of the vessels of a fleet from each vessel
(the fleet may have until 20 vessels max).
'MENU' + "C-STAFF" + 'ENTER'
For more information see the specific User Manual.
5.8 C-METEO
To set up the information relative to the display of the weather information
on the map.
'MENU' + "C-METEO" + 'ENTER'
For more information see the specific User Manual.
88 User Manual
5.9 FISH FINDER MENU
The chart plotter combined with the sonar performance of the Fish Finder is
one of the most advanced marine navigation system available.
'MENU' + "FISH FINDER SETUP" + 'ENTER'
For more information see the specific User Manual.
89
User Manual
6
For the Technician
6.1 DIMENSIONS
Fig. 6.1 - EXCALIBUR models Dimensions
90 User Manual
Fig. 6.1a - COMPACT models Dimensions
6.2 INSTALLATION AND REMOVING
Fig. 6.2 - EXCALIBUR models Installation
91
User Manual
Fig. 6.2a - COMPACT models Installation
To remove the chartplotter press the bracket button (1) as indicated in the
following Fig. 6.2b (left side of the picture for EXCALIBUR models and right side of
the picture for COMPACT models) and then eject to the top the chart plotter (2).
Fig. 6.2b - EXCALIBUR models (left side) and COMPACT models (right side) removing
92 User Manual
6.3 EXTERNAL WIRING
Fig. 6.3 - External Wiring for chartplotter with external GPS receiver
Fig. 6.3a - External Wiring for chartplotter with internal GPS receiver
93
User Manual
6.4 TYPICAL CONNECTIONS
Fig. 6.4 - Beacon Receive Connection for chartplotter with internal GPS receiver
94 User Manual
Fig. 6.4a - GPS Connection on Port 3 for chartplotter with external GPS receiver
95
User Manual
Fig. 6.4b - Autopilot Connection on Port 2
Fig. 6.4c - External NMEA Connection on Port 1
Fig. 6.4d - C-COM Connection on Port 1
96 User Manual
6.5 TROUBLESHOOTING
The following is a brief guide to some of the problems you may experience
while using the chartplotter with common solutions.
6.5.1 PROBLEMS AND SOLUTIONS
The chartplotter does not turn On — Make sure that the correct voltage (10-35
volt dc) is present. Check also that the polarity is correct. Refer to the Par. 2.2.
The chartplotter does not turn Off — If, after a 'POWER' pressure (for at least 3
seconds) the chartplotter does not turn Off, then turn Off the voltage.
The chartplotter does not respond to any command — Try to turn Off, and then
turn On. If the problem persists, erase the memory (see Par. 6.6.1).
The chartplotter does not get a valid fix — Make sure that no metal obstacle is
placed around the chartplotter acting as a shield for the antenna. If, after 15 minutes,
the chartplotter does not get the fix, turn it Off and On again.
The chartplotter screen becames very dark after a long exposure to direct sun-
light — Control the contrast (see Par. 2.3).
6.5.2 HELP
If you want to activate a function, the chartplotter has an help on line:
'MENU' + "Help" + 'ENTER'
Use 'ZOOM IN' and 'ZOOM OUT' to select the previous and the next
page.
6.5.3 IF YOU NEED ASSISTANCE
The list above (see Par. 6.4.1) should allow you to solve most of the operat-
ing problems you are likely to encounter. Simply disconnecting the chartplotter
from power for a moment may solve your problem as well.
If this does not help, you can try one additional memory clear option. This
is a factory default RAM Clear that should only be tried after all other attempts have
been made. When using the RAM Clear feature, you will loose all user stored infor-
mation and the chartplotter will default to factory settings. Before this step, you
97
User Manual
have the option of saving user Marks, Track history and Routes to a User C-CARD
(this is an optional purchase from your dealer). To perform a RAM Clear see Par.
6.6.1.
If you still need assistance, call your local dealer, reporting the Software Re-
lease and Cartography information available in the About page.
'MENU' + "About..." + 'ENTER'
6.5.3.1 World Background Charts
The internal background charts can be updated to include the MAX A and
B level charts which provide improved marine data, rivers, lakes, terrestrial data
(major streets , highways , railways, etc...), Nav-Aids, depth areas, territorial water
areas, etc... by reading them from a special data C-CARDs (contact your local dealer).
All units must have the WorldWide Background upload function that is activated
from the system.
Worldwide Background Update
The System Update menu is entered from the About page. To select this menu fol-
low the procedure:
Plug the special data C-CARD + 'MENU' + "About..." + 'ENTER' + 'MENU' +
"Update Worldwide Charts" + 'ENTER'
6.6 SYSTEM TEST
If you have connected your position-finding device according to the instruc-
tions, and chosen the proper menu selection for your device, and are still having
problems with your chartplotter, the extended auto-test should help determine the
problem. Make sure the chartplotter is turned Off. While pressing and holding any
other key, turn the chartplotter On. A new menu will appear on the display:
Fig. 6.6 - System Test
98 User Manual
Use the cursor key to select the preferred test: this will display in reverse
video and with the relative menu window. To choice the test press 'ENTER'. To
exit from any submenu press 'CLEAR'. To exit from the System Test turn Off the
chartplotter.
6.6.1 RAM MENU
This test verifies the integrity of the memories and if preferred during this
test all the internal memory can be erased and the default setting restored.
RAM Test
To verify the integrity of the RAM. If on the screen the message "ERROR"
appears, the RAM is physically damaged.
RAM Clear
To clear internal memory. If the chartplotter exhibits unusual behaviour, or appears
to be malfunctioning, it may be possible to correct the problem by clearing RAM.
This operation will erase all Marks, Events, Routes, stored track plots and desti-
nations. It will also return all selections (Input Data Format, Autopilot selection,
etc.) to original default values. To confirm to clear RAM press 'ENTER' again
(but if at this time you do not wish to clear RAM press 'CLEAR').
6.6.2 DIM MENU
To select the preferred value for contrast and backlight.
Contrast
Each time you pressed thecursor key to right, the screen will decrease brightness,
instead of to left it will increase brightness.
Backlight
To set the backlight. Operates in similar mode as Contrast.
6.6.3 CARTRIDGES
To check the C-CARD and its connector.
Background ROM
To test the WorldWideBackground. If there is not a malfunction, the code of the
Background and the message "OK" are shown.
C-CARD Test
To test the C-CARD. There are the possible situations:
99
User Manual
1. if there is a C-CARD inserted in the slot and there is not a malfunction, the
name of the C-CARD zone and the message "OK" are shown.
2. if there is a C-CARD inserted in the slot, but it is a damaged C-CARD, the
name of the C-CARD zone and the message "Faulty" are shown.
3. if there is not any C-CARD inserted in the slot, the message "not present" is
shown.
4. if there is an User C-CARD inserted in the slot, the message "USER C-CARD"
is shown.
C-CARD Connector
Indicates if there is a malfunction in the connector. It is used only in production.
6.6.4 SERIAL PORTS
If you are having problems receiving data from the position-finding instru-
ment, this test should help determine the problem.
Change Parameters
Allows to change the parameters of the serial interface. This menu allows to
select the Port (Signal Source) between Port 1, Port 2 or Port 3, the Baud Rate
between 4800 or 9600, the Data Bits (Word Length) between 7 or 8, the Parity
between even, odd or none, the Stop Bits between 1 or 2.
Input Data Display
Allows the chartplotter to act as a computer terminal and display the incoming
data exactly as it received.
If the data displayed on the screen is unrecognizable, you may have selected the
wrong input parameters for your particular receiver. Check your receiver manual
to be sure that you have selected the proper interface format. If the screen is
blank, you may have a broken connection and no data is being received.
Use 'ZOOM IN' to stop (or continue after pause) data displaying, 'ENTER' to
show data in hex or ASCII mode (normal or small) and 'CLEAR' to exit.
6.6.5 MODEM TEST
To check the Modem connections. Press 'ENTER' to select the preferred
Port (Port 1 or Port 2
FOR
CHARTPLOTTER
WITH
INTERNAL
GPS
RECEIVER
, Port 1, Port
2 or Port 3
FOR
CHARTPLOTTER
WITH
EXTERNAL
GPS
RECEIVER
) related to the connec-
tions made, to the Port that the Modem C-COM is connected.
100 User Manual
101
User Manual
A
Ter ms
This section explains the terms that may be unfamiliar to the reader.
Advanced Mode
The chartplotter can operate in two different modes: Basic Mode and Advanced Mode. In Advanced
Mode it is possible to have more available functions, for example it is possible to handle Waypoints.
Altitude
Altitude of GPS Antenna on the medium sea level.
Arrival Time
The estimated time of day you will reach your destination, based on your current speed and track from
GPS.
Attention Areas
Attention Areas are areas in which special attention by the mariner is required, because of natural or
man-made hazards, or sailing regulations and restrictions. Moreover a special symbol (!) is placed inside
the area selecting On option. This is valid also for the categories: FISHING FACILITY, MARINE
FARM/CULTURE, MILITARY PRACTICE AREA, RESTRICTED AREA, SEAPLANE LAND-
ING AREA. When the area is small, it is identified only by the boundary.
Azimuth
The angular measurement from the horizon to a satellite or another object.
Basic Mode
The chartplotter can operate in two different modes: Basic Mode and Advanced Mode. In the first
mode there is a restricted number of functions, and it is not possible to handle Waypoints, Marks,
Events and A-B-C-D function.
Beacon
A prominent, specially constructed object forming a conspicuous vertical mark as a fixed aid to navigation.
Buoy
A floating object moored to the sea bottom in a particular (charted) place, as an aid to navigation.
Buoys and Beacons
Buoys and Beacons are used to indicate to mariners recommended or established routes, underwater
dangers, restrictions and regulations. They can be lighted or not and - for the color chartplotter - are
coloured according to their international code.
BRG = Bearing
It is the angle between the North (True or Magnetic) and a destination. It represents the direction to
follow.
102 User Manual
Chain
Selects the preferred chain. The Loran chains are groups of transmitting stations that use timed radio
pulse transmissions. In each of these chains there is a master station and two or more slave or secondary
stations. Stations belonging to a same chain transmit pulses in timing groups: a different time base
identifies each chain. The time base of each chain is the Group Repetition Interval or GRI. This GRI
identifies the chain in unique mode. For example the GRI = 4990 identifies the chain of Central Pacific
zone.
COG = Course Over Ground
Direction of the path over ground actually followed by a vessel.
Correction
To compute fix error in automatic mode, place cursor on ship's real position and then follow the
procedure (compute correction). It is also possible to compute the fix error in manual mode (correction
offset). Once you computed the error, you can turn the fix correction On or Off.
Course Vector
The Course Vector is a graphical indication of the direction in which the Vessel is heading. The Course
Vector origin is the vessel’s position so the time line movement is synchronized with the vessels Icon.
Course Vector course is given by the value of COG (Course Over Ground) and its length is propor-
tional to the SOG (Speed Over Ground).
CTS = Course To Steer
The optimum direction the boat should be steered in order to efficiently make headway back to the
courseline while also proceeding toward the destination Waypoint.
Cultural Features
Any man-made topographic feature as built-up area, buildings, roads, ....
Datum
The Latitude and Longitude lines printed on any map are based on certain models of the shape of the
earth: these models are called Datum or Coordinate Systems. There are many different Datum in use,
each one gives different Lat/Lon positions for an identical point on the surface of the earth.
Default
Indicates a value or a setting which is used if the user has not defined a particular value. You can modify
this value using the menu settings.
Depth Lines
Imaginary lines connecting points of equal water depth.
DGPS = Differential GPS
Provides even greater positioning accuracy than standard GPS.
Event
User Point that refers to the ship's position. It is simply a way of marking where the boat is.
File
Collection of information (of the same type) stored on a User C-CARD. Each file must have a unique
name, ideally one that describes its contents. Filenames are kept in a directory on each User C-CARD.
Goto
Sets a particular mark on the map, called Target or Destination.
GPS = Global Positioning System
It is a satellite based navigation system operated by the US Department of Defense. It gives the naviga-
tor a position 24 hours a day, 365 days a year under any weather conditions .
103
User Manual
HDG = Heading
The horizontal direction in which a ship actually points or heads in any moment (see also COG).
HDOP = Horizontal Dilution Of Precision
It is the index for position-fixing accuracy. The smaller the HDOP value, the more accurately the
position can be fixed
Home
In this operating mode (called also Navigate mode) all operations refer to the ship's position.
Latitude
The angular distance North or South of the equator measured by lines encircling the earth parallel to
the equator in degrees from 0° to 90°.
LAT/LON
Coordinate system using Latitude and Longitude coordinates to define a position on earth.
LOG
Speed of the vessel relative to the water.
Longitude
The angular distance East or West of the prime meridian (Greenwich meridian) as measured by lines
perpendicular to the parallels and coverging at the poles from 0° to 180°.
Loran
The Loran Chains are groups of transmitting stations that use timed radio pulse transmissions.
Magnetic Deviation
The angle between the Magnetic North and the Compass North.
Magnetic Variation
The angle between the magnetic and geographic meridians at any place, expressed in degrees West or
East to indicate the direction of magnetic North from true North. It changes from point to point, and
(at the same point) with time.
Mark
Reference points related to cursor position.
Natural Features
Any topographic feature formed by the action of natural processes: coastlines, relief, glaciers, ....
Navigate (mode)
Operating mode (called also Home mode) all operations refer to the ship's position.
NMEA-0183
The NMEA-0183 Data Interface Standard was developed by the National Marine Electronics Associa-
tion of America. It is an international standard that enables equipment from many different manufac-
tures to be connected together and to share information.
Pictures and Diagrams
The MAX data format allows assigning one or more image to any cartographic object. These Pictures
are typically used to facilitate the identification of cartographic objects or places around the map: they
can be the landscape layout nearby a harbor, the shape of a bridge or of a buoy etc.
On some objects, such as bridges, the image associated can represent the Diagram representing the
shape of the objects and the various characteristics (length, heigh, type of bridge etc.).
104 User Manual
Fig.A.1 - Pictures and Diagrams
OSGB = Ordnance Survey of Great Britain
A coordinate system describing only Great Britain. Generally used with GBR36 datum, which also
describes only Great Britain. This coordinate system cannot be used in any other part of the world.
Port Info
The Port Info function is a combination of a new Port Info database containing all the relevant Safety
and Navigational information normally found in good pilot books and a new presentation software
which displays special Port Facility Symbols.
Ports & Services
Areas along shore with facilities for mooring, downloading and uploading of ships, generally sheltered
from waves and winds. Port installations are piers, wharves, pontoons, dry docks, cranes... .
Route
Sequence of Waypoints connected by segments. Among the available Routes, only one is the active
Route, which is shown by a straight line and arrows to indicate the direction.
RTCM = Radio Technical Commission for Maritime Services
The data format created by the Radio Technical Commission Maritime to transmit Differential GPS
corrections.
SOG = Speed Over Ground
A calculation of the rate of movement of the ship over the ground.
Speed
The current velocity at which you are travelling, relative to a ground location.
Spot Sounding
Depth of the water in a specific and charted position
STR = Steering
The difference between COG and CTS. If COG is 25° and CTS is 30°, then STR is 5° Right.
Target
In order to tag on the chart the point, towards which the ship is Heading, you can use a special mark,
called Target. When the Target is placed, all navigation data are referred to this Target.
TD = Time Difference
Loran positions are determined by precise timing of the intervals between reception of pulses transmit-
ted by pairs of stations in the selected chain. Between any two stations a ship must be located some-
where along a line of possible positions where the measured Time Difference, TD, between arrival of
pulses from those stations would be observed. The TD is measured from the time of reception of the
master station signal to the time of reception of the slave station signal.
Tide
The periodic rise and fall of the surface of oceans, bays, etc., due principally to the gravitational interac-
tions between the Moon and Earth.
105
User Manual
Tide Info
The Tide Info feature is the combination of a new tide heights database that will be included within
new C-CARDs and new features which calculate the tide graph for all primary and secondary ports
world-wide. This function can calculate the tide heights for any past or future date and as a by-product
of this calculation will also display the Maximum and Minimum Tide height and time for the day
selected plus the times of Sunrise and Sunset. At some chart levels, the chartplotter will display a new
Tide Diamond Symbol for every Port or tide point in the database covered by that particular C-CARD.
Tide & Currents
The new worldwide database with tidal stream information is now available with MAX C-CARDs.
When data/time is available, Tidal stream arrows are shown on the charts, indicating the direction and
strength of the Tide.
Fig. A.1a - Tides & Currents
If no data/time is available from the GPS or the chart plotter is not in Simulation mode, the icon on the
map is generic one. The colour of the arrow denotes the strength of the current as follows:
Fig. A.1b - Tides & Currents table
When the chart plotter receives a valid position fix, the Tide icons are shown on the charts on the basis
of the current date and time: the screen displays and changes arrows as date/time changes.
Time Line
The location where the ship will be after the time set by the user.
Tracks & Routes
Recommended and established routes for ships at sea, including traffic separation schemes, deep water
routes, ....
TRN = Turning
The difference between COG and BRG. If COG is 80° and BRG is 75°, TRN is 5° Left.
TTG = Time To Go
The estimated time needed to reach your destination, based on your current speed and the distance to
destination.
User Point
Place on the chart identified by its coordinates and displayed on the screen with a reference symbol (see
Mark, Waypoint and Event).
106 User Manual
UTC = Universal Time Coordinated
A time scale based on the rotation of the earth that is used by most broadcast time services.
UTM = Universal Transverse Mercator
Metric Grid system used on most large and intermediate scale land topographic charts and maps.
VAD = Value Added Data
The Value Added Data (VAD) is a collection of additional cartographic objects which are not present
on the original paper chart (from which the electronic chart derives). These objects have been obtained
from other sources (that C-MAP believes to be reliable) and then merged to the electronic charts in
order to provide more information useful for the navigation.
VAD object can be any cartographic objects and it can be distinguished from the official-chart-objects
from the Quick Info. A dedicated icon is shown on the Quick Info window to indicate that the object
queried is a VAD.
The same icon is also shown on the Full Info page and in addition the extended text Value Added Data
is shown on the details of the VAD object.
WAAS = Wide Area Augumentation System
The Federal Aviation Administration (FAA), in cooperation with other DOT organizations and DOD,
is augmenting the GPS/SPS with a satellite-based augmentation system, the WAAS. It will provide a
signal-in-space to WAAS users to support en route through precision approach navigation. After achieving
initial operational capability, the WAAS will then be incrementally improved over the next years to
expand the area of coverage, increase the availability of precision approaches, increase signal redun-
dancy and reduce operational restrictions.
Waypoint
Any point to which one intends to navigate. A sequence of Waypoints makes up a Route plan .
WGS-84 = World Geodetic System 1984
Coordinates System or Datum developed by the Defense Mapping Agency (DMA).
Zoom-In
Shows more detail in a smaller area.
Zoom-Out
Operates similarly to zoom -in, but in the reverse, showing a wider but less detailed view.
XTE = Cross Track Error
The distance from the ship's present position to the closest point on a line between the origin and
destinations Waypoints of the navigation leg being traveled.
107
User Manual
B
Smart DGPS WAAS Receiver
The Smart DGPS WAAS receiver is based on a ultimate 12 channel GPS
engine that delivers accuracy better than three meters by decoding the GPS correc-
tion signals from the satellite-based WAAS (Wide Area Augmentation System). The
GPS engine, interface electronics and the passive antenna are enclosed inside the
water-proof plastic housing. This provides advanced state of the art GPS perfor-
mance in an easy to use package.
Note
The characteristics of your Receiver could not be the same as the following explained. Contact the
dealer the chartplotter was purchased from for more information.
B.1 TECHNICAL SPECIFICATIONS
B.1.1 PYSICAL CHARACTERISTICS
Color : Ivory white
Dimensions : 97mm in diameter x 32mm in height (flush mounted) or
61,5mm on flag-pole mount
Weight : 160 grams (without cable)
Cable : white 15 meter 8x28AWG cable
B.1.2 ELECTRICAL CHARACTERISTICS
Input Voltage : 10 Vdc to 35 Vdc unregulated
Power Consumption : 1,2 Watt
B.1.3 GPS PERFORMANCE
Geodetic Datum : WGS84
Channels : 12 parallel Channels
Frequency : 1575.42MHz (L1, C/A code)
108 User Manual
Acquisition Time (Approximate)
Hot start : < 20 seconds
Warm start : < 45 seconds
Cold start : < 40 seconds
DGPS Capability : RTCM SC104 v. 2,WAAS (North America), EGNOS
(Europe), MSAS (Asia)
Output Format : NMEA 0183 Version 2.0, Baud Rate 4800, N81
Interfaces : Asynchronous serial output compatible with RS-232
(TTL voltage levels) RS-232 polarity
B.1.4 ENVIRONMENTAL CHARACTERISTICS
Operating Temperature: 0° C~ +60° C
Storage Temperature : -20° C~ +85° C
Relative Humidity : 95% non-condensing
Water Resistance : 100% waterproof
B.2 WIRING
See the following table for a functional description of each wire in the GPS cable.
Fig. B.2 - GPS Connection
B.3 SOFTWARE INTERFACE
The GPS products interface protocol design is based on the National Marine
Electronics Association's NMEA-0183 ASCII interface specification. These standards
109
User Manual
are defined in "NMEA-0183 Version 2.0" (for more information see NMEA,
www..nmea.org).
B.4 MECHANICAL CHARACTERISTICS & MOUNTING
B.4.1 INSTALLING
Choose a location for the antenna that has a clear view of the sky. Ensure
there are no major obstructions or fixtures in the immediate proximity to the an-
tenna. The antenna relies on direct “line of sight” satellite reception. If you are un-
sure that the chosen location is suitable it may be advisable to mount the antenna in
a temporary manner to verify correct operation. The thread used on the antenna (1
inch, 14 TPI) is an industry standard thread used on a wide range of mounting brack-
ets, including the swivel joints commonly used for angled surfaces. However due to
the manufacturing process of these mounting brackets you may see that there is
some slop when tightening down the antenna to the bracket. This is of no concern
however as the antenna must be tightened until the antenna stops rotating on the
antenna mounting bracket.
Fig.B.4.1 - Installing GPS Antenna (I)
The antenna design also allows for easy flush mounting.
1. Apply the adhesive mounting template sheet in the area that was verified
to receive satellite signal well.
2. Then, following template instruction, drill a 0,95 inch (24 mm) hole and
three 0,155 inch (4 mm) holes.
110 User Manual
Fig.B.4.1a - Installing GPS Antenna (II)
3. Remove the template and let the cable go through the central hole.
4. Apply a small coat of RTV to the underside of the antenna.
5. Place the antenna and then screw it with the three M3 screws.
Fig.B.5.4.1b - Installing GPS Antenna (III)
B.4.2 DIMENSIONS
Fig.B.4.2 - GPS Antenna Dimensions
111
User Manual
Analytical Index
A
A-B-C-D function ........................... 35, 67
Add to Route .................................. 65, 67
Adding Event ........................................ 66
Adding Mark .......................................... 63
Adding Waypoint .................................. 53
Additional Second Factor ..................... 82
Advanced Functions ............................. 31
Advanced Mode ............. 18, 31, 53, 101
Advanced Settings ............................... 79
Alarms menu ........................................ 84
Alternate Solution ................................. 82
Altitude ......................................... 32, 101
Anchor Alarm ........................................ 85
Antenna .............................................. 109
Arrival Alarm ......................................... 84
Arrival Time ........................................ 101
ASF ....................................................... 82
assistance ............................................. 96
Attention Areas ............................ 43, 101
Automatic Info ...................................... 45
Autopilot ................................................ 22
Autopilot Connection ............................ 22
Azimuth ............................................... 101
B
Background ROM ................................. 98
backlight .................................. 17, 19, 98
Backlight Timeout ................................. 80
Basic Mode .................... 18, 31, 53, 101
Basic Settings Menu ............................. 31
Beacon ................................................ 101
Beacon Receiver Connection ............... 24
Bearing ............................................... 101
Bearings ................................................ 84
Beeper .................................................. 80
BRG .................................................... 101
Buoy .................................................... 101
Buoys ID ............................................... 42
C
C-CARD ......................................... 24, 98
C-CARD Connector .............................. 99
C-CARD Test ........................................ 98
C-COM .................................................. 23
C-COM Connection .............................. 23
C-COM GSM Plus ............................... 23
C-Link ............................................ 34, 73
C-Staff ................................................... 87
C-Voice ................................................. 34
Cable Wiring Page ............................... 34
Calibration ............................................. 84
Cartridges ............................................. 98
Caution Notice ...................................... 19
Chain ............................................ 82, 102
Change Parameters ............................. 99
Changing Speed & Fuel ....................... 62
Changing User C-CARD ....................... 72
Chart Boundaries .................................. 45
chartplotter ............................................ 15
Charts ................................................... 27
COG .................................................... 102
Color .................. 12, 59, 61, 65, 67, 69
Compass menu .................................... 83
Compute Correction ............................. 81
consumption ......................................... 15
contrast ................................... 17, 19, 98
Conventions .......................................... 11
Coordinate System ............................... 82
Correction .................................... 81, 102
Correction Offset .................................. 81
Course Over Ground .......................... 102
Course To Steer ................................. 102
Course Vector .............................. 31, 102
Creating a route .................................... 54
Cross Track Error ............................... 106
CTS ..................................................... 102
Cultural Features ......................... 44, 102
Currents Prediction ............................... 41
Cursor Control ...................................... 87
cursor key ............................................. 18
Cursor Speed ........................................ 32
D
Date ...................................................... 87
Date Format .......................................... 80
112 User Manual
Datum ................................................. 102
Dead Reckoning ................................... 82
Default ................................................ 102
Deleting A-B-C-D ........................... 36, 68
Deleting Event ...................................... 66
Deleting File .......................................... 72
Deleting Mark ........................................ 63
Deleting MOB ....................................... 51
Deleting route ......................... 55, 61, 62
Deleting Selected Track ....................... 69
Deleting Target .............................. 37, 56
Deleting Track ...................................... 69
Deleting User Point .............................. 60
Deleting Waypoint ......................... 46, 54
Depth ............................................. 31, 32
Depth Alarm .......................................... 85
Depth Areas .......................................... 44
Depth Graph ......................................... 29
Depth Lines ......................................... 102
Depth Window ...................................... 31
DGPS .................................. 12, 102, 107
Diagrams ............................................ 103
Differential Correction Source .............. 34
Differential GPS .................................. 102
Dim Menu ............................................. 98
Dimensions ........................................... 89
Display Mode ................................. 38, 45
Displaying Track ................................... 69
Distance ................................................ 32
distance (track) ..................................... 70
Dynamic Nav-Aids ................................ 40
E
Echosounder ........................................ 35
Editing Event ........................................ 66
Editing Mark .......................................... 64
Editing Waypoint .................................. 58
Enabling Track storing .......................... 69
Event ............................................ 65, 102
Expanded Info page ............................. 46
Extern Waypoint ................................... 80
External Connections ........................... 20
External NMEA Connection .................. 22
External Wiring ..................................... 92
F
Features ................................................ 37
File ............................................... 71, 102
Filter ...................................................... 81
Filter Dump ........................................... 81
Find Function ........................................ 49
Find Port ............................................... 49
Finding Port Services ........................... 97
Finding User Point ................................ 59
Fish Finder ............................................ 88
Fix Correction ....................................... 81
Fix Datum ............................................. 82
Fix menu ............................................... 80
Fonts & Symbols .................................. 39
Formatting User C-CARD ..................... 72
Fuel ....................................................... 62
Functions Menu .................................... 17
G
Goto ...................................... 63, 66, 102
GPS ...................................... 20, 29, 102
GPS cable .......................................... 108
GPS Connection ................................... 20
GPS Data Page .................................... 29
GPS Performance .............................. 107
GPS Setup Menu .................................. 33
Graphic Data Page ............................... 30
Grounding Alarm .................................. 85
Grounding Alarm Range ....................... 86
Grounding Alarm Report ...................... 86
GSM ...................................................... 23
H
HDG .................................................... 103
HDOP .................................................. 103
Heading ....................................... 86, 103
Help ....................................................... 96
Home ........................................... 17, 103
I
Info Function ......................................... 47
info Tree ................................................ 46
Input Data Display ................................ 99
Inserting A-B-C-D ................... 35, 67, 68
Inserting C-CARD ................................. 25
Inserting MOB ....................................... 50
Inserting Waypoint ................................ 57
Installation ............................................ 90
K
key ........................................................ 15
Keyboard ....................................... 15, 17
L
Land Elevation Values .......................... 44
Landmarks ............................................ 44
language ............................................... 19
LAT/LON ............................................. 103
Lat/Lon Grid .......................................... 44
Latitude ............................................... 103
LCD Display .......................................... 14
113
User Manual
Light Sectors ......................................... 43
line pattern ............................................ 69
Loading File .......................................... 72
LOG .................................................... 103
Longitude ............................................ 103
Loran ................................................... 103
M
Magnetic Deviation ............................. 103
Magnetic Variation .............................. 103
Man OverBoard .................................... 18
Map Datum ........................................... 83
Map Menu ...................................... 13, 38
Map Orientation ............................. 39, 83
Map Presentation ................................. 45
Marine Settings ..................................... 24
Mark ............................................. 63, 103
MAX ...................................................... 37
Memory ................................................. 15
Mixing Levels ........................................ 40
MOB ............................................... 18, 50
Modem Test .......................................... 99
Moving A-B-C-D .................................... 68
Moving Mark ......................................... 63
Moving Waypoint .................................. 56
N
Names .................................................. 42
Natural Features ................................. 103
Nav-Aids ........................................ 40, 43
Navigate ....................................... 17, 103
Navigate menu ..................................... 82
Navigating on A-B-C-D .................. 36, 68
Navigation ............................................. 34
Navigation Data Page ........................... 30
Navigation Speed ................................. 34
Nearest Services .................................. 49
NMEA .................................................... 22
NMEA WPL & RTE ............................... 62
NMEA-0183 ........................................ 103
O
Obstructions ......................................... 50
OSGB .......................................... 82, 104
Other Map Configurations .................... 42
Output Port ........................................... 35
P
Pair ........................................................ 82
Palette ................................................... 38
Perspective View .................................. 38
Phisical Characteristics ........................ 14
Pictures ............................................... 103
POIs ...................................................... 44
Port 1/Port 2/Port 3 Input ..................... 32
Port 1/Port 2/Port 3 NMEA Output ....... 33
Port 1/Port 2/Port 3 Output ................... 33
Port Info ....................................... 47, 104
Ports & Services .......................... 43, 104
Position Filter ........................................ 81
problems ............................................... 96
R
RAM Clear ............................................ 98
RAM Menu ............................................ 98
RAM Test .............................................. 98
Receiver ................................................ 12
removing ............................................... 91
Removing C-CARD .............................. 25
Reset Partial Trip .................................. 83
Reset Total Trip .................................... 83
Restart GPS ......................................... 33
Reversing route ............................. 61, 62
Rivers & Lakes ..................................... 44
Roads ................................................... 44
Rocks < ................................................. 44
Rocks > ................................................. 44
Rolling Road Page ................................ 30
Rolling Road Scale ............................... 83
route ...................................... 54, 60, 104
Route Name ......................................... 62
Route Report ........................................ 61
RTCM .................................................. 104
S
Safety Status Bar ................................. 40
Saving File ............................................ 71
screen display ....................................... 27
Seabed Type ........................................ 43
Selecting active Track .......................... 69
Selecting Route .................................... 60
Selecting route ...................................... 62
Selecting track line pattern ................... 69
Send & Receive Marks/Routes ............ 34
Send/Receive Route ............................. 62
Serial Ports ........................................... 99
Setup menu .......................................... 79
Simulation Mode ................................... 86
Simulator ............................................... 86
size ........................................................ 14
Smart DGPS WAAS Receiver ........... 107
SOG .................................................... 104
Specifications ....................................... 12
Speed ..................... 32, 62, 81, 86, 104
Speed Filter .......................................... 81
Speed Over Ground ........................... 104
114 User Manual
Spot Sounding .................................... 104
Static Navigation ................................... 82
Steering .............................................. 104
STR ..................................................... 104
Structure ............................................... 41
Surface Clutter ...................................... 41
System Test .......................................... 97
System Update ..................................... 97
T
Target ............................ 17, 36, 55, 104
TD ................................................ 82, 104
Temperature .................................. 15, 32
Text Area ....................................... 17, 27
Tide ............................................ 104, 105
Tide & Currents .................................. 105
Tide Graph ............................................ 48
Tide Info ....................................... 47, 105
Tide Stations ......................................... 50
Tides & Currents ................................... 43
Time ...................................................... 87
time (track) ............................................ 70
Time Difference .................................. 104
Time Format ......................................... 79
Time Line ............................................ 105
Time Reference .................................... 79
Time To Go ........................... 36, 56, 105
title page ............................................... 19
track ...................................................... 68
Track memorizing type ......................... 70
Tracks & Routes .......................... 44, 105
TRN ..................................................... 105
TTG .............................................. 56, 105
Turning ................................................ 105
Turning Off ............................................ 19
Typical Connection ............................... 93
U
Underwater Objects .............................. 44
Units Selection ...................................... 32
User C-CARD ................................ 70, 99
User Point ...................... 31, 59, 65, 105
User Points List ...................... 59, 65, 67
UTC .............................................. 79, 106
UTM ............................................. 82, 106
V
VAD ..................................................... 106
Value Added Data ....................... 45, 106
Variation ................................................ 84
Voice Menu ........................................... 34
voltage .................................................. 18
W
WAAS ................................. 12, 106, 107
Waypoint ............................... 53, 80, 106
Weight ................................................... 14
WGS-84 .............................................. 106
Wind Speed .......................................... 80
World Background Charts .................... 97
Wrecks .................................................. 50
X
XTE ..................................................... 106
XTE Alarm ............................................ 85
Z
Zoom Type .......................................... 39
Zoom-In .............................................. 106
Zoom-Out ............................................ 106
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lorenz COMPACT 7 Plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lorenz COMPACT 7 Plus in de taal/talen: Engels als bijlage per email.

De handleiding is 3,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info