Handleiding Loewe klang s1 (pagina 25 van 380) (Alle talen)

807074

Verklein

Vergroot

Pagina terug

1/380

Pagina verder

Loewe klang s1/s3

deutsch

english

[Info]

[Privacy policy]

[Backlight]

[Ambient Light]

19 Equaliser

With the equalizer you can adjust the sound of

the radio to your liking. You can choose from pre-

configured settings or create your own profile.

Please proceed as follows:

Press the button and select [System Set-

tings] and then [Equaliser]. Alternatively, you

can press the button on the remote control.

You can select a sound profile with the or

buttons and then confirm with OK. The follo-

wing profiles are available: [Normal] / [Flat] /

[Jazz] / [Rock] / [Movie] / [Classic] / [Pop]

/ [News] / [My EQ]

Setting up [My EQ]:

To do this, please navigate to [My EQ profile

setup] and confirm with OK. The [Bass] and

[Treble] can now be set in the following menu.

Confirm the [Bass] or [Treble] with the OK

button, make the appropriate settings with

the or buttons and confirm with the

OK button. When you have finished adjusting

the bass and treble, press and hold the

button to save the changes. Select [YES] and

press OK to save this new equalizer profile.

The active sound profile is marked with [*].

20 Network settings

20.1 Network wizard

The network wizard helps to connect the radio

to the Internet. To call it up, please proceed as

follows: Select the [Network] in the [System

Settings] menu and then confirm [Network

wizard]. The radio now starts a search for

available WLAN connections and then lists

them. The various networks can be selected

using the or buttons. At the end of the

list there is the option to select [Rescan] or

[Manual config].

20.2 Wireless network

connection (WLAN)

Depending on the network, you have several

options to choose from to connect to the net-

work. Networks that support a WPS connection

(Wi-Fi Protected Setup) are identified in the list

by the preceding designation [WPS ...]. Other

connections are open networks or connections

that are protected by the password.

Note: An active network connection is indicated

by a white symbol at the bottom right of the

display. If no connection is active, this symbol

is crossed out.

20.3 WPS/Password protected/

Open connection

A WPS connection enables the radio to be

connected to your network in a simple yet pro-

tected manner. There are two options available.

Establishing the connection through

PBC = Push-Button-Configuration (configu-

ration at the push of a button) or by the PIN

procedure, in which the web interface of your

router prompts you to enter a randomly gene-

rated sequence of numbers.

20.4 PBC setup

Select the desired network [WPS ...]. Then

select the [Push button] option in [WPS

menu] and confirm. Now press the WPS

button on your router or access point (AP).

Please refer to the operating instructions of

your router or AP for the exact procedure.

Then press the OK button on the remote

control or radio to initiate a network

connection. Alternatively, the process can

also be started in the [Network] menu under

[PBC WLAN setup]. Follow the instructions

on the display.

20.5 Setup using PIN

Select the desired network [WPS ...]. Then

use the [WPS menu] to select and confirm

the [PIN] option. The radio now generates an

8-digit code, which you should confirm with the

OK button and then enter the number via the

user interface of the router or AP. Please refer to

the Router or AP manual for more information.

20.6 Skip WPS/Setup using

password

Select [Skip WPS] to establish the connection

using the Wi-Fi password. In the case of net-

works without WPS support, you can directly

enter the password. Now enter the password

and confirm it with the [OK] button. If the entry

is correct, the radio connects to your network

and establishes an Internet connection.

20.7 Open connection

We recommend that you do not connect to an

open network. If the network you have selected

is not encrypted, you can confirm this with the

OK button. Then the internet connection is

established.

20.8 Manual network connection

setup

If DHCP is active, please proceed as follows:

Please select the menus [Network] -> [Manu-

al settings] -> [Wireless] -> [DHCP enable].

Then enter the full SSID (network name) and

confirm it with the [OK] button. Now choose

the appropriate encryption method.

Please refer to the configuration of the router

or AP. Depending on the method selected, the

network key is now entered and confirmed with

the [OK] button.

If DHCP is inactive, please proceed as

follows:

Please select the menus [Network] -> [Manu-

al settings] -> [Wireless] -> [DHCP disable].

Now enter the information for [IP address],

[Subnet mask], [Gateway address], [Pri-

mary DNS] and [Secondary DNS]. The

values can be set using the or button.

Use the OK, or to select the individual

number. Then proceed as described under

[DHCP active].

20.9 Show network settings

In this menu you will find all settings of the net-

work profile currently in use. To do this, select

the [View settings] menu in the [Network]

menu. The values can be displayed using the

or button.

20.10 NetRemote PIN setup

In this menu you can set a 4-digit PIN that will be

requested when the “Loewe radio” App is set up

for the first time. The default is “1234”. The PIN

should be changed immediately.

20.11 Network profile

Here you can see the list of network profiles

saved on the radio. If you have created several

profiles, choose the one closest to the corre-

sponding router or AP.

You can delete network profiles that are no

longer required by pressing the or button

to select the profile to be deleted and confirm

with the OK button. The active network profile

is marked with [*].

Note: The active network profile cannot be

deleted.

20.12 Clear network settings

In this menu you can delete the network settings

of the current profile. To do this, select the [YES]

button and confirm your entry with the OK.

Selecting the [NO] button cancels the process.

20.13 Keep network connected

This menu is used to set whether the WLAN

connection to the network should be maintained

in standby mode. This enables you to switch

on the radio using the “Loewe radio” App. This

means that the power consumption in standby

mode is somewhat higher. Select the [YES]

or [NO] button for the setting and confirm the

entry with the OK.

Equaliser | Network Settings

Loewe klang s1 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info