793229
14
Verklein
Vergroot
Pagina terug
1/85
Pagina verder
14 GB/IE
Safety/Start-up
Verify the existing mains voltage matches the
required operating voltage of the lamp (see
“Technical data“) before use.
Ensure that the light does not come into contact
with water or other liquids under any circumstances.
Always unplug the lamp from the mains prior
to assembly, disassembly, cleaning or if the
lamp will not be used for extended periods.
Never open any of the components of the elec-
trical equipment or insert any objects into the
same components. This will pose a risk of fatal
injury from electric shock.
The illuminant in this light must be replaced by
the manufactured or an authorised technician
or similarly qualified person.
This light is not suitable for dimmer
or electronic switches.
Prevent fire and injury hazards
Do not look into the illuminant from a close
distance during operation.
Do not look at the LED with an optical instrument
(e.g. magnifier).
Do not cover the lamp or the mains plug with
objects. Excessive heat can result in a fire.
Do not operate the lamp unattended.
For your safety
Mount the light so that it is protected from
moisture and dirt.
Always be attentive! Always pay attention to
what you are doing and always proceed with
caution. Never mount or use the light if you are
having difficulty concentrating or do not feel well.
In order to disconnect the light completely from
the power supply, the mains plug must be
removed from the socket.
Start-up
Installing the light
Note: Remove all packaging materials from the
product.
Note: During assembly, make sure that you pull the
power cord 3 slowly through the base 1.
Carefully remove the bottom of the base 1b
(see Fig. A).
Insert the standpipe 2 into the base 1 (see
Fig. B). Make sure that the power cord
3
,
which
runs through the standpipe 2, is not pinched.
First slide the washer 4, then the toothed
washer 4 and finally the nut 6 onto the
standpipe 2 from below (see Fig. C).
Then tighten the nut 6 using the tool 7 (see
Fig. C). Pay attention to the correct fit. Place
the power cord 3 in the base 1 as shown in
Figure D. Make sure that the power cord 3 is
not pinched inside the base 1.
Then place the assembled lamp on the bottom
of the base 1b . Make sure that the power cord
3 is in the recess provided on the underside
of the base 1b (see Fig. E).
Screw the bottom of the stand 1b tight with the
screws 8 provided (see Fig. F).
Glue the screw covers 9 to the intended loca-
tion on the screws 8 (see Fig. G).
Insert the mains plug 13 into a properly installed
socket (see Fig. H).
The lamp is now ready for use.
Switch the lamp on and off
Switch the light on or off using the ON/OFF
switch 12 (see Fig. H).
Adjusting the reflector
CAUTION! RISK OF BURNS DUE TO
HOT SURFACES!
Note: Only change the position of the reflector 10
if the lamp is turned off.
Start-up/Maintenance and cleaning/Disposal/Guarantee and service
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Livarno IAN 378535 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Livarno IAN 378535 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens als bijlage per email.

De handleiding is 1.22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info