805908
10
Verklein
Vergroot
Pagina terug
1/17
Pagina verder
18 19
Note
-The alarm will sound for 2 minutes if you do not deactivate it by pressing any button. In this case the
alarm will be repeated automatically after 24 hours.
-Rising alarm sound (crescendo, duration: 2 minutes) changes the volume 4 times whilst the alarm signal
is heard.
Switching off the alarm signal
Press any button except the “ ” button to stop the alarm signal. It is not necessary to reactivate the
alarm. The alarm will set itself automatically to the previously set time.
Snooze function
Touch the “ “ eld or press the “ ” button to activate the snooze function. The alarm signal
will sound again after approx. 5 minutes.
Lunar phases
The weather station has a display which automatically displays the current lunar phase
°C/°F temperature display
-The temperature is displayed either in °C or °F. Briey press the “ ” button to switch between the
individual modes.
Comfort display
-indoor comfort level is calculated according to the indoor temperature and humidity, a total of 5 levels.
Displaying temperature/humidity/barometric pressure and temperature/humidity trend
-The current indoor temperature/humidity/barometric pressure and the temperature/humidity trend
(indoors) are shown in the LCD display.
-After successfully connecting with the remote sensor, the weather station can display the remote tem-
perature/humidity and the temperature/humidity trend (remote)
-You may see the following displays:
The temperature/humidity is rising.
The temperature/humidity is remaining constant.
The temperature/humidity is falling.
1.
1.
New moon Waxing
half-moon Half-moon Waxing full
moon
Full
moon
Waning full
moon Half-moon Waning
half-moon
Comfortable Too cold or too hot
Remote sensor transmission
When the Weather Station successfully receives signals from the wireless sensor, the temperature and
humidity of the “REMOTE SENSOR” are displayed on the “REMOTE SENSOR” column of the weather
station. The weather station can connect with up to 3 channel wireless sensors, but you can only choose
one channel at a time.
Press the “ ” key to switch the display of different channels of remote temperature and humidity. When
the “ “ is displayed, the channel will automatically switch every 5 seconds to different channels.
If the weather station failed to receive transmission from a remote sensor (“- -”display on the LCD),
press and hold the “ ” button for 3 seconds to receive transmission manually. The remote temperature
will show an animation of the RF antenna symbol, the Base Station will re-receive the wireless signal of
the remote sensor.
Note
-When the wireless sensor sets different channels, the weather station “REMOTE SENSOR” also wants
to switch to the same channel. When there is no wireless sensor signal transmission on the channel, “--”
will be displayed in the channel of the weather station
-When the wireless remote sensor has no channel selection function, the sensor defaults to channel 1.
Maximum / Minimum Temperature/and Relative Humidity
To switch between indoor/remote maximum, minimum temperature and humidity data, press the
“MEM” button:
-Once to display the maximum temperature and humidity values.
-Twice to display the minimum temperature and humidity values
-Three times to return to the current temperature and humidity levels
To reset the maximum and minimum temperature and humidity, press and hold down the “MEM”
button for about 2 seconds. This will reset all minimum and maximum data recorded to the current
displayed values.
Note
-If the temperature reading is below the temperature range, tLL.L will be displayed. If the temperature
reading is above the temperature range, HH.H will be displayed.
Setting the Remote Temperature Alert
Press and hold down the “ ” button for 2 seconds until the “Temperature Alert” icon starts to ash
The icon of Upper limit of the Temperature alarm starts to ash. Use the “ ” and “ ” buttons to set
the required maximum temperature. Press “ ” to conrm your setting.
The icon of the Lower limit of the Temperature alarm starts to ash. Use the “ ” and “ ” buttons to set
the required minimum temperature. Press “ ” to conrm your setting and to end the setting procedure
Note:
-Before entering the setup, you must select the correct channel, different channels can set different
temperature alarm ranges.
Temperature and frost alert
Press “ ” to activate or deactivate the remote temperature alert. When the remote temperature alarm
is activated, the temperature alarm icon is displayed in the remote sensor bar.
When the remote channel temperature value exceeds the set temperature range, the alarm will be acti-
vated. The Weather Station alarm will sound 5 times continuously every minute, while the temperature
alarm “ “ ashes. If the temperature activates the alarm, the upper limit icon “ “ or the lower limit
icon “ “ also ashes.
When the temperature of REMOTE SENSOR is –1°C to + 3°C or +30°F to + 37°F, the frost alarm will be
activated, the symbol “ “ will ash.
1.
2.
1.
2.
3.
1.
2.
3.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

LifeGoods-LG1177

Zoeken resetten

  • Hallo,
    Ik heb een weerstation van lifegood , sinds enkele dagen produceert het station steeds een heel irritante piep. Ik heb nieuwe batterijen in het station en de buiten sensor gedaan, doch de piep blijft. Dat duidt volgens mij op een of andere storin. Kunt hier iets over zeggen.? Gesteld op 20-8-2024 om 09:33

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw LifeGoods LG1177 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van LifeGoods LG1177 in de taal/talen: Nederlands, Engels, Frans als bijlage per email.

De handleiding is 0.57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info