716906
15
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
uCarefully lift up the plugs with a slotted screwdriver and
remove them. Fig. 35 (1)
uPosition the door from above onto the lower bearing pins.
Fig. 35 (2)
uInsert the centre bearing pin through the centre bearing
bracket into the lower door. Make sure that the catch
mechanism is pointing to the rear. Fig. 35 (3)
uInsert the plugs again on the other side of the door.
Fig. 35 (4)
4.3.12 Fitting the upper door
Fig. 36
uPlace the upper door on the centre bearing pins Fig. 36 (1)
uAlign the top of the door with opening in the bearing
bracket. Fig. 36 (2)
uInsert the bolt and tighten with a T15 screwdriver.
Fig. 36 (3)
uFit the protective cover to protect the door: Insert the
protective cover and check that it is attached to the door.
If not, insert the bolt fully. Fig. 36 (4)
NOTICE
Cable crushing
uThe mark on the cable must be centred in the holder. The
tab with the longer opening must point forwards.
uInsert the holder with its cable into the opening.
Fig. 36 (5)
uPress the holder downwards until the tab clicks into
place. Fig. 36 (6)
uInsert the plugs. Fig. 36 (7)
4.3.13 Fitting the cable connection
Fig. 37
uEngage the plug above the upper bearing bracket and
carefully place the cable strands into the channel.
Fig. 37 (1)
uCarefully position the grey cable in the guide above the
top bearing bracket. Fig. 37 (2)
Fig. 38
uInsert the grey cable into the guide in the top door.
Fig. 38 (1)
uEngage the plug. Fig. 38 (2)
uPosition the remaining cable length as a loop in the
guide, if required.
4.3.14 Aligning the doors
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly
enough, the door may drop out. This may lead to severe
injuries. What is more, the door may not close and therefore
the appliance may fail to cool properly.
uScrew the turn hinges firmly into place with 4 Nm.
uCheck all of the screws and retighten if necessary.
uAlign the doors flush with the appliance housing using
the two oblong holes in the lower bearing bracket and
centre bearing bracket if needed. To do this undo the
middle screw in the bottom bearing bracket with the T25
tool supplied. Undo the remaining screws a little with
the T25 tool or with a T25 screwdriver and align using
the slotted holes. Undo the screws in the middle bearing
bracket with the T25 tool and align the middle bearing
bracket using the slotted holes.
Putting into operation
* Depending on model and options 15
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Liebherr SWTNes 4285 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Liebherr SWTNes 4285 in de taal/talen: Engels als bijlage per email.

De handleiding is 2.28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Liebherr SWTNes 4285

Liebherr SWTNes 4285 Gebruiksaanwijzing - Nederlands - 34 pagina's

Liebherr SWTNes 4285 Gebruiksaanwijzing - Deutsch - 34 pagina's

Liebherr SWTNes 4285 Gebruiksaanwijzing - Français - 34 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info