715385
15
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
u
Insert the holder with its cable into the opening.
Fig. 36 (5)
u
Press the holder downwards until the tab clicks into place.
Fig. 36 (6)
u
Insert the plugs.
Fig. 36 (7)
4.3.13 Fitting the cable connection
Fig. 37
u
Engage the plug above the upper bearing bracket and care-
fully place the cable strands into the channel.
Fig. 37 (1)
u
Carefully position the grey cable in the guide above the top
bearing bracket.
Fig. 37 (2)
Fig. 38
u
Insert the grey cable into the guide in the top door.
Fig. 38 (1)
u
Engage the plug.
Fig. 38 (2)
u
Position the remaining cable length as a loop in the guide, if
required.
4.3.14 Aligning the doors
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough,
the door may drop out. This may lead to severe injuries. What is
more, the door may not close and therefore the appliance may
fail to cool properly.
u
Screw the turn hinges firmly into place with 4 Nm.
u
Check all of the screws and retighten if necessary.
u
Align the doors flush with the appliance housing using the
two oblong holes in the lower bearing bracket and centre
bearing bracket if needed. To do this undo the middle screw
in the bottom bearing bracket with the T25 tool supplied.
Undo the remaining screws a little with the T25 tool or with a
T25 screwdriver and align using the slotted holes. Undo the
screws in the middle bearing bracket with the T25 tool and
align the middle bearing bracket using the slotted holes.
u
Support the door: Take off the adjustable foot on the bearing
bracket using the open-ended wrench SW10 until it comes
into contact with the floor, then turn an additional 90°.
4.3.15 Fit the bottom soft stop mechanism
Fig. 39
u
Slide the soft stop mechanism on the bearing bracket side at
an angle into the slot as far as the limit stop.
Fig. 39 (1)
u
Slide the soft stop mechanism fully into the slot.
Fig. 39 (2)
w
The unit is positioned correctly when the rib on the soft stop
mechanism is in the guide.
u
Tighten the screw with the T15 screwdriver.
Fig. 39 (3)
u
Push the cover over the hinge.
Fig. 39 (4)
Fig. 40
The door is open 90°
u
Turn the hinge in the mount.
Fig. 40 (1)
u
Insert the bolt with a T15 screwdriver in the mount and
hinge. Make sure that the catch mechanism is sitting
correctly in the groove.
Fig. 40 (2)
u
Push the bearing bracket cover along the hinge and fit on
the mount.
Fig. 40 (3)
u
Remove the locking device.
Fig. 40 (4)
u
Position the panel on the handle side and swing it in.
Fig. 40 (5)
w
The panel is clicked into place.
u
Close the bottom door.
Putting into operation
* Depending on model and options 15
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Liebherr SBSes 8496 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Liebherr SBSes 8496 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Liebherr SBSes 8496

Liebherr SBSes 8496 Gebruiksaanwijzing - Nederlands - 62 pagina's

Liebherr SBSes 8496 Installatiehandleiding - Deutsch - 6 pagina's

Liebherr SBSes 8496 Gebruiksaanwijzing - Deutsch - 30 pagina's

Liebherr SBSes 8496 Gebruiksaanwijzing - Français - 26 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info