Handleiding Liebherr GNP 2713-23 (pagina 8 van 14) (Engels)

710260

Verklein

Vergroot

Pagina terug

1/14

Pagina verder

When installing with kitchen units (max. depth 580 mm), the

appliance can be positioned directly next to the kitchen cabinet

Fig. 10 (3)

. The appliance will project by 34 mm

at the sides

and 50 mm

in the centre of the appliance in relation to the

kitchen cabinet front.

NOTICE

Danger of overheating due to insufficient air ventilation!

The compressor may be damaged if there is insufficient air

ventilation.

Take care to ensure adequate air ventilation.

Observe the ventilation requirements.

Ventilation requirements:

At the back of the stack cabinet there has to be a ventilation

duct of at least 50 mm depth throughout the width of the

stack cabinet.

The cross section of the ventilation gap below the ceiling

must be at least 300 cm

the larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 10 (4)

, the distance between appliance and wall has to be

at least 40 mm. This corresponds to the projection of the

handle when the door is open.

4.5 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film!

Do not allow children to play with packing material.

The packaging is made of recyclable materials:

corrugated board/cardboard

expanded polystyrene parts

polythene bags and sheets

polypropylene straps

nailed wooden frame with polyethylene panel*

Take the packaging material to an official collecting point.

4.6 Connecting the appliance

NOTICE

Failure to connect properly

Damage to the electronics.

Do not use a standalone inverter.

Do not use an energy saving plug.

WARNING

Failure to connect properly

Fire hazard.

Do not use an extension cable.

Do not use distributor blocks.

The type of current (alternating current) and voltage at the

installation site have to conform with the data on the type plate

(see 1 Appliance at a glance) .

The socket must be properly earthed and fused. The tripping

current for the fuse must be between 10 A and 16 A.

The socket must be easily accessible so that the appliance can

be quickly disconnected from the supply in an emergency. It

must be outside the area of the rear of the appliance.

Check the electrical connection.

Plug in the power plug.

4.7 Switching on the appliance

Press the On/Off button

Fig. 3 (1)

The appliance is switched on. The temperature display and

Alarm symbol

Fig. 3 (10)

flash until the temperature is cold

enough.

If “DEMO” is displayed, demo mode is activated. Please

contact the after sales service.

5 Control

5.1 Brightness of the temperature

display

You can adjust the brightness of the temperature display to the

light conditions of the room in which the appliance is installed.

5.1.1 Adjusting the brightness

The background lighting can either be turned off or set to one

of 5 levels. The factory setting is that the background lighting is

turned off.

To activate the setting mode: Press the SuperFrost button

Fig. 3 (2)

for about 5 seconds.

The menu symbol

Fig. 3 (9)

shines and the child lock symbol

Fig. 3 (8)

flashes.

Press the setting button

Fig. 3 (6)

to select the brightness

function.

The child lock symbol

Fig. 3 (8)

turns off and the brightness

symbol

Fig. 3 (3)

flashes.

To confirm: Briefly press the SuperFrost button

Fig. 3 (2)

The brightness symbol

Fig. 3 (3)

shines.

Using the setting button

Fig. 3 (6)

, select either "off" or the

brightness wanted. The more display fields of the tempera-

ture display that light up, the brighter it is. If no field is lit up, it

means "off".

To confirm: Press the SuperFrost button

Fig. 3 (2)

The brightness symbol

Fig. 3 (3)

flashes.

The brightness is adjusted to the new value.

To deactivate the setting mode: Press the On/Off button

Fig. 3 (1)

-or-

Wait for 5 minutes.

The brightness symbol

Fig. 3 (3)

and the menu symbol

Fig. 3 (9)

go out.

The temperature is indicated again in the temperature

display.

5.2 Child proofing

The child-proofing function enables you to make

sure that the appliance is not inadvertently switched

off by playing children.

5.2.1 To activate child lock

To activate the setting mode: Press the SuperFrost button

Fig. 3 (2)

for about 5 seconds.

The menu symbol

Fig. 3 (9)

shines and the child lock symbol

Fig. 3 (8)

flashes.

Briefly press the SuperFrost button

Fig. 3 (2)

to select the

child lock function.

The child lock symbol

Fig. 3 (8)

shines. The

-15 °C and -21 °C LEDs shine in the temperature

display.

Control

8 * Depending on model and options

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Liebherr GNP 2713-23 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Liebherr GNP 2713-23

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info