Handleiding Lenovo px4-300d - LifeLine 4.0 (pagina 152 van 164) (Engels)

611571

152

Verklein

Vergroot

Pagina terug

1/164

Pagina verder

Configuring Port Forwarding on Double NAT Networks

If for some reason the network configuration cannot be changed and your setup requires the double NAT,

you must perform the port forwarding steps twice. On the primary router, set the port forwarding to the

cascaded router's external IP address. On the cascaded router, set the port forwarding to the px4-300d's

IP address.

Bridging the Secondary Router

Make sure that the primary router (usually the one connected to or acting as the DSL/Cable modem) is the

only one with DHCP (Dynamic Host Configuration Protocol) and NAT (Network Address Translation)

enabled. The secondary should be changed to bridging mode. Ensure that the secondary router connects

to the primary router using a standard port rather than the port labeled Uplink or internet. This turns your

secondary router into a switch; however, you can still enable its Wireless Access Point if so equipped.

Refer to the documentation that came with your router for configuration information and settings.

Bridging the Primary Router

If none of the above options are available, you must enable transparent bridging on your primary router.

This may require contacting your ISP (Internet Service Provider) to configure the DSL or Cable

Modem/NAT into bridge mode, which then disables the first NAT/Firewall. After this first firewall in the

modem is disabled, the secondary router handles all the network traffic, Port Forwarding, and allows

Remote Access to work.

You should not attempt bridging without help from the ISP. If bridge mode is attempted by the

customer and not configured properly, it can render the customer's internet connection inoperable.

Primary router bridging may also require special configuration information and settings on the

secondary router.

If you configured your px4-300d using DHCP, you may not be able to reconnect to it via Remote Access

after a reboot. DHCP automatically receives an IP address from the server whenever the px4-300d

restarts. This is a very simple way to configure the px4-300d but can cause problems with your router's

port forwarding settings. The router does not dynamically update port forwarding settings and cannot port

forward to your px4-300d if its IP address changes.

To resolve this problem, try one of the following processes:

● Increase the length of the DHCP lease: Your router attempts to remember all DHCP clients and

assigns them the same IP address every time they request an IP address; however, the router

forgets clients if they do not request an IP address for a certain amount of time. Your router has a

setting for the duration of the validity of the DHCP lease. If your network requires DHCP, this

may be a good solution; however, it is not always guaranteed to work. Occasionally updating your

router's port forwarding settings may be required.

● Use Static DHCP: Some routers allow you to assign Static IP addresses through the DHCP

system based on the MAC address of the device. This ensures that the px4-300d always gets the

same IP address, and your port forwarding settings are always correct. Static DHCP allows you

to leave your px4-300d in DHCP mode. Refer to your router's documentation for more information

on configuring DHCP settings.

● Use a Manual IP Address: Changing the Manual IP address reduces the reliance of your px4-300d

on the DHCP server; however, you must perform additional configuration for it to work properly.

1. Log in to your router and write down the DHCP range it is using.

Hardware Management

Troubleshooting Routers 142

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Lenovo px4-300d - LifeLine 4.0 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Lenovo px4-300d - LifeLine 4.0

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info