646122
5
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
DigiLevel Pro 30/60/120
GB
08
GB
09
Keypad
1. (REF) – Angle reference value setting
2. ( ) – ON / OFF switch
3. (
)
)
) ) – Acoustic signal on/off
4. (MR) – Memory retrieval
5. (UNIT) – Unit of measurement selection
(° degrees / % / IN/FT)
6. (M) – MEMORY function
Display
7. Slope direction
8. Slope angle
9. Current memory position (M1 – M9)
10. Battery charge
DigiLevel Pro 30/60/120
11. Vertical vial
12. Horizontal vial
13. Magnets
14. Measuring surface, 30 / 60 / 120 cm
15. Point laser ON / OFF
16. Tripod threads, 1/4"
Rear
17 . Battery compartment
1
Inserting batteries:
Open the battery compartment (17) on the rear of the DigiLevel and
insert two new batteries (type AAA/LR03) in the manner indicated
by the installation symbols. Ensure correct polarity. The symbol (10)
indicates the level of battery charge.
Digital electronic spirit level with vertical and horizontal angle display and
point laser (650 nm).The slope can be indicated in degrees, IN/FT or percent
on the display.An acoustic signal indicates the horizontal or vertical position.
The slope memory enables angles to be projected elsewhere, while
the separate measurement memory allows up to 9 measurements results
to be stored and retrieved. Milled measuring surfaces, powerful xing
magnets, as well as additional vertical and horizontal vial, illuminated display.
Calibration function for increased accuracy and adaptation to measuring
surface.
Switching on and measuring:
The DigiLevel Pro can measure angles continuously to 360°.
• Switch the DigiLevel Pro on using the on/off switch (2).
• The current operating temperature in °C is shown for a few seconds.
The slope angle is shown in the display (8). If slopes are measured
overhead, the direction of display adjusts automatically.
• The current slope direction is also shown by the symbol (7).
Selection of unit of measurement:
Button (5) allows the desired unit of measurement to be selected
(° degrees, %, IN/FT)
Changing the angle reference value:
With button (1), it is possible to transfer angles elsewhere. To do so,
set the device to the desired slope and press button (1). The display will
then change to “0.0”, and the desired reference angle is now set.
The slope can now be transferred to other objects.
IMPORTANT: When all the slopes have been transferred, make sure
to deactivate the new angle reference value. To do this, switch off
the device by pressing the on/off switch (2) for at least 3 secs. Only
then will the value be reset itself to the measuring surface (14).
Acoustic signal:
• The acoustic signal can be switched on or off with button (3).
• When the angle of slope stands at 0°, 45°, 90° or the most recently
stored value, this is indicated by an acoustic signal.
NOTE: When working with a changed angle reference value, the
acoustic signal is activated on reaching the new reference value
(0°, 45°, 90° display).
2
3
5
6
4
11
12
13
14
15
17
16
97108
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Laserliner DigiLevel Pro 30 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Laserliner DigiLevel Pro 30 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens als bijlage per email.

De handleiding is 0,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info