797099
1
Verklein
Vergroot
Pagina terug
1/1
Pagina verder
TECHNICAL DETAILS
Hardware
Power supply Internal power supply unit (100–240 V, 50-60 Hz)
Power consumption Max. 36 W
Environment Temperature range 0–40 °C, humidity 0–95 %; non-condensing
Housing Robust metal housing, 1 HU with mounting brackets for 19“ installation, W 345 x H 44 x D 253 mm)
Number of fans 1 quiet fan
Interfaces
G.FAST / VDSL 1 / VDSL 2 AG.FAST according to ITU G.9700 and G.9701, profiles 106a, 212a
AVDSL2 according to ITU G.993.2, profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a, 35b
AVDSL supervectoring according to ITU G.993.2 (Annex Q)
AVDSL2 vectoring: according to ITU G.993.5 (G.Vector)
ACompatible with VDSL2 from Deutsche Telekom
ACompatible with the U-R2 connection of Deutsche Telekom (1TR112)
AADSL2+ over ISDN according to ITU G.992.5 Annex B/J with DPBO, ITU G.992.3 and ITU G.992.1
AADSL2+ over POTS according to ITU G.992.5 Annex A/M with DPBO, ITU G.992.3 and ITU G.992.1
ASupports only one virtual connection in ATM (VPI-VCI pair) at a time
AAutomatic detection of Deutsche Telekom VDSL connections with VLAN ID 7
WAN 1 / WAN 2 WAN 1 SFP: Compatible with optional LANCOM SFP modules. Set as a WAN port ex-factory, can be configured
as a LAN port.
WAN 1 / WAN 2 TP: 10 / 100 / 1000 Base-TX, autosensing full duplex (WAN 1) / autosensing (WAN 2), auto
node hub
ETH1 - ETH 4 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode. Up to 3 ports can be
operated as additional WAN ports. Ethernet ports can be electrically disabled in the LCOS configuration.
Analog 1 - Analog 4 Use the cables of your analog devices to connect them with the analog interfaces. If necessary, use the enclosed
adapters.
ISDN 1 / ISDN 2 ISDN 1: Internal (NT) ISDN bus. Connect the ISDN interface to an ISDN cable and the ISDN device.
ISDN 2: Internal (NT) ISDN bus. Connect the ISDN interface to an ISDN cable and the ISDN device.
Config (Com) / V.24 Serial configuration interface / COM-port: 9,600 - 115,200 baud
USB USB 2.0 hi-speed host port for connecting USB printers (USB print server), serial devices (COM-port server) or
USB drives (FAT file system)
4G Two SMA connectors for the supplied dipole rod antennas (LTE, UMTS), compatible LANCOM
AirLancer antennas for 4G, or from other manufacturers. Please respect the restrictions which apply in your
country when setting up an antenna system (particularly antenna gain / transmission power).
WAN protocols
G.FAST, VDSL, ADSL,
Ethernet
PPPoE, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without DHCP), RIP-1, RIP-2, VLAN, GRE,
EoGRE, L2TPv2 (LAC or LNS), IPv6 over PPP (IPv6 and IPv4/IPv6 dual stack session), IP(v6)oE (autoconfiguration,
DHCPv6 or static)
ISDN DSS1 (Euro-ISDN), PPP, X75, HDLC, ML-PPP, V.110/GSM/HSCSD
Data transmission in cellular networks
Supported standards UMTS, HSxPA, HSPA+, LTE, LTE Advanced
Supported cellular
network bands
Band 1 (2100 MHz), Band 3 (1800 MHz), Band 7 (2600 MHz), Band 8 (900 MHz), Band 20 (800 MHz), Band 28
(700 MHz), Band 32 (1500 MHz), Band 38 (2600 MHz), Band 40 (2300 MHz), Band 41 (2500 MHz), Band 42
(2500 MHz), Band 43 (2500 MHz)
Max. transmission power +23 dBm
Declaration of Conformity
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives
2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity
is available at the following Internet address: www.lancom-systems.com/doc
Package content
Documentation Quick Reference Guide (DE/EN), Installation Guide (DE/EN)
Cables 2 DSL cables for IP-based connection, 4.25 m, or 2 DSL cables, 3 m (dark blue connectors), depending on the
version;
1 Ethernet cable, 3 m (kiwi colored connectors); 1 IEC power cord 230 V (not for WW devices)
Antennas Two LTE / 4G antennas for LTE / UMTS
Adapters 4 TAE adapters (RJ11 - TAE)
Mounting brackets Two 19” brackets for rack mounting
MOUNTING AND CONNECTING THE DEVICE
f ISDN 1 (NT) / ISDN 2 (NT)
Off Interface deactivated
Green, permanently D-channel active
Green, blinking ISDN connection active
Orange, blinking ISDN connecting
Green / orange, blinking
synchronously
ISDN hardware error
Orange, permanently Connection inactive
c G.FAST / VDSL 1 / VDSL 2
Off Interface deactivated
Green, blinking DSL connecting
Green, pemanently DSL connection active
Green, flickering DSL data transmission
Green / orange,
flickering
DSL transmission error
Green / orange, blinking
synchronously
DSL hardware error
Orange, blinking DSL training
Orange, permanently DSL sync
e ETH 1 - ETH 4
Green, orange off No networking device connected
Green, permanently Connection to network device operational,
no data traffic
Green, flickering Data transmission
Orange off 1000 Mbps
Orange, permanently 10 / 100 Mbps
d WAN 1 / WAN 2
Green, orange off No networking device connected
Green, permanently Connection to network device operational,
no data traffic
Green, flickering Data transmission
Orange off 1000 Mbps
Orange, permanently 10 / 100 Mbps
b RESET
Reset button Short press > restart the device
Long press > reset the device
*) The additional power LED statuses are displayed in 5-seconds rotation
if the device is configured to be managed by the LANCOM Management
Cloud.
This product contains separate open-source software components which
are subject to their own licenses, in particular the General Public License
(GPL). The license information for the device firmware (LCOS) is available
on the device‘s WEBconfig interface under “Extras > License information“.
If the respective license demands, the source files for the corresponding
software components will be made available on a download server upon
request.
a c eb fd
4
Please observe the following when setting up the device
AThe mains plug of the device must be freely accessible.
AFor devices to be operated on the desktop, please attach the adhesive rubber
footpads
ADo not rest any objects on top of the device and do not stack multiple devices
A Keep the ventilation slots on the side of the device clear of obstruction
AMount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.
Pay attention to the “R” and “L” marks on the brackets for accurate mounting.
a4G / LTE antenna connectors
Connect the supplied cellular antennas to the connectors
at the front of the device.
bG.FAST / VDSL / ADSL interfaces*
If required, use the supplied DSL cables for the IP-based line to
connect each G.FAST / VDSL / ADSL interface to a separate provid-
er’s telephone socket. For more information, please contact your
Internet service provider.
* Please use the appropriate cables depending on the design
cWAN 1 interfaces (SFP / TP combo port)
Insert a suitable SFP module (e.g. 1000Base-SX or 1000Base-LX)
into the SFP port. Choose a cable compatible with the SFP module
and connect it as described in the module’s documentation. SFP
modulel and cable are not included.
If desired, alternatively connect the WAN 1 TP interface to a WAN
modem using an ethernet cable.
dWAN 2 interface (TP)
Connect the WAN 2 interface to a WAN modem using an Ethernet
cable.
eEthernet interface
Use the cable with the kiwi-colored connectors to connect one of
the interfaces ETH 1 to ETH 4 to your PC or a LAN switch.
fAnalog interfaces
Connect analog terminal devices to the analog interfaces either
directly via RJ11 or with the help of the enclosed TAE adapters.
gISDN interfaces
ISDN 1: Internal (NT) ISDN bus
ISDN 2: Internal (NT) ISDN-bus
A 100-Ohm resistor for line termination is
switchable in LCOS.
hSIM card slots
Slide the SIM card(s) into slot SIM1 or SIM2 using the marker
to ensure that the card is the right way round. Ensure that the
SIM card clicks into place on insertion. To remove the card from
the device, press the card lightly into the device.
Let go to release the SIM card from the slot. SIM
iConfiguration interface
Use the included serial configuration cable to connect the serial
interface (COM) to the serial interface of the device you want to
use for configuring / monitoring.
jUSB interface
You can use the USB interface to connect a USB printer or a
USB storage device.
k
l
Power connector and grounding point (device back side)
Supply power to the device via the power connector. Please
use the IEC power cable supplied (separately available for WW
devices).
ATTENTION: High touch current possible! Connect to earth
before connecting the power supply.
Warning! High touch current.
Connect to earth before
connecting the power supply.
hi
j
j
cd
bef
POWER
RESET
VPN
VoIP
4G
VDSL 2 WAN 1 WAN 1 WAN 2 ETH 1 ETH 2 ETH 3 ETH 4 ANALOG 1 ANALOG 2 ANALOG 3 ANALOG 4 ISDN 1 (NT) ISDN 2 (NT)
SIM 2
SIM 1
COM USB
LANCOM 1926VAG-4G
Systems
G.FAST / VDSL 1
1
1
1
1
g
POWER
RESET
VPN
VoIP
4G
VDSL 2 WAN 1 WAN 1 WAN 2 ETH 1 ETH 2 ETH 3 ETH 4 ANALOG 1 ANALOG 2 ANALOG 3 ANALOG 4 ISDN 1 (NT) ISDN 2 (NT)
SIM 2
SIM 1
COM USB
LANCOM 1926VAG-4G
Systems
G.FAST / VDSL 1
K
K
L
L
LANCOM 1926VAG-4G
Quick Reference Guide
Cloud-ready
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document
contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111963/0122
a 4G / VoIP / VPN / POWER
4G
Off Cellular interface disabled
Green,permanently Connection to cellular network active
Green, flickering Cellular data transmission
Orange, permanently Logon to cellular network successful
Orange, blinking Logging on to cellular network
Red, permanently Hardware error / module unavailable
Red / green, blinking SIM card error (PIN)
Red / orange, blinking Uploading module firmware
VoIP
Off No SIP accounts defined or VCM is off
Green, permanently All defined and active SIP accounts
(outgoing) were successfully registered
Red, permanently Not all of the defined and active SIP accounts
were registered (possibly still in process)
Red or green, inverse
flashing
Number of currently used lines
(connecting or connected)
VPN
Off VPN connection inactive
Green, permanently VPN connection active
Green, flashing VPN connecting
POWER
Off Device switched off
Green, permanently* Device operational, resp. device paired /
claimed and LANCOM Management Cloud
(LMC) accessible
Green / red, blinking No password set. Without a password
the configuration data in the device is
unprotected.
Red, blinking Charge or time limit reached
1x green inverse blinking* Connection to the LMC active, pairing OK,
device not claimed
2x green inverse blinking* Pairing error, resp. LMC activation code not
available
3x green inverse blinking* LMC not accessible, resp. communication
error

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lancom 1926VAG-4G bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lancom 1926VAG-4G in de taal/talen: Engels als bijlage per email.

De handleiding is 0.41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Lancom 1926VAG-4G

Lancom 1926VAG-4G Installatiehandleiding - Deutsch - 19 pagina's

Lancom 1926VAG-4G Snelstart handleiding - Deutsch - 1 pagina's

Lancom 1926VAG-4G Installatiehandleiding - English - 19 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info