812600
8
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
MANUAL FOR USE AND MAINTENANCE
8 LSC 001 -UK- REV. 06
HEATING PHASE AND PRESET PHASE FOR OPERATION
(Range New - Rapid - Spazio - S3)
In the S5 1 GROUP range , turn the switch knob to position 2 (boiler heating element ON )
a) Fasten the lter holders (11) to the delivery groups (16).
b) Open the steam valves (5) (turning them anticlockwise) and leave them open; then move the steam
wands (8) over the grid (10).
c) Wait for steam to come out of the wands (8) (about 15 / 20 minutes) then close the steam valves (5)
(turning them clockwise).
d) Wait for the appliance to reach operating temperature, which can be seen on the pressure gauge (4)
on the appliance (1 bar pressure).
On the Seletron model it is possible to view the temperature in ° set during the installation phase
being reached on the display (33).
NOTE. The operating temperature is the boiler temperature during normal operation.
e) The appliance is ready for use.
HEATING PHASE AND PRESET PHASE FOR OPERATION
(Range S5 - Compact)
a) Fasten the lter holders (11) to the delivery groups (16).
b) Open the steam valves (5) (moving the lever upwards) and leave them open; then move the steam
wands (8) over the grid (10).
c) Wait for steam to come out of the wands (8) (about 15 / 20 minutes) then close the steam valves (5)
by moving the lever back to its original position.
d) Wait for the appliance to reach operating temperature, which can be seen on the pressure gauge (4) on
the appliance (1 bar pressure). For S5 range models, check the control panel (13) to make sure that the
temperature set at the time of installation, given in °C, has been reached. During the heating phases,
make sure that the symbols on the control panel (13) switch on in progression as the temperature rises.
The display will start to show this as soon as the temperature reaches 105 °C and will continue until
the appliance reaches its operating temperature (the set temperature symbols will go from ashing to
xed). Each time that the temperature drops to below the SET level, the symbol indicating the operating
temperature will start to ash (heating phase) until the set temperature is reached.
NOTE. The operating temperature is the boiler temperature during normal operation.
e) The appliance is ready for use.
COFFEE PREPARATION
a)
Remove a lter holder (11/a or 11/b according to whether 1 or 2 cups of coffee are required) from the
delivery
group (16).
b) Fill it with ground coffee, taking care not to leave any coffee powder on the top edge of the lter holder.
Press down the coffee with the special coffee tamper provided.
c) Firmly re-attach the lter holder to the group, without tightening it excessively.
d) Place one or two cups below the lter holder (according to whether it is for 1 or 2 cups of coffee).
e) Push the button (12) on the delivery group until the required of amount of coffee has been delivered,
then manually stop the delivery function by pressing the same button again.
f) For EK and Seletron models, it is sufcient to press any of the coffee delivery buttons (25-26-27-28)
with pre-set doses (set during installation) or alternatively, to use the manual delivery button (29).
NOTE. To stop coffee delivery earlier after using one of the buttons with pre-set doses, just press
the button (29) on the same touchpad (except for range Super 3000 Seletron model).
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw La Spaziale RAPID bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van La Spaziale RAPID in de taal/talen: Engels als bijlage per email.

De handleiding is 1.91 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info