Handleiding La Nordica Gaia Forno (pagina 24 van 88) (Duits, Engels, Frans, Italiaans, Spaans)

696155

Verklein

Vergroot

Pagina terug

1/88

Pagina verder

ENGLISH

The stove is equipped with controls of primary and secondary air by which it is adjusted the combustion air.

1A - PRIMARY air register (Picture 6)

With the register on the door of the ash-drawer it is adjusted the passage of air through the drawer of ash and the grate in the fuel direction.

The primary air is necessary for the combustion process. The ash drawer must be regularly emptied, so that the ash does not obstruct the

primary air entry for the combustion. Through the primary air the re is also kept alive.

During wood combustion, the register of primary air must be opened only for a while, because otherwise the wood burns fast and the stove

may overheat. The register is open when the lever is completely pulled out. The register is closed when the lever is introduced (see chapter

NORMAL OPERATION).

2A - SECONDARY air register (Picture 6)

On the inferior part ( pos. B) and on the over part ( pos. C) of the door there is the secondary air control. Also this control must be opened

(then moved to the right), especially for wood combustion, so that unburnt carbon does not undergo a post-combustion (see chapter

NORMAL OPERATION).

The adjustment of the registers necessary to reach the rated caloric yield is the following one:

Hourly consumption in Kg/h PRIMARY air SECONDARY air TERTIARY AIR

GAIA 1,7

CLOSED OPEN

PRE-ADJUSTED

GAIA Forno 1,7

CLOSED OPEN

PRE-ADJUSTED

FULVIA

1,7

CLOSED OPEN

PRE-ADJUSTED

FULVIA Forno

1,7

CLOSED OPEN

PRE-ADJUSTED

FLUE

Essential requirements for correct appliance operation:

• the internal section must preferably be circular;

• the appliance must be thermally insulated and impermeable and built with suitable materials which are resistant to heat,

combustion products and any condensation;

• there must be no narrowing and vertical passages with deviations must not be greater than 45°;

• if already used, it must be clean;

• all the sections of the ue gas duct must be accessible to inspection;

• inspection openings must be provided for cleaning.

• the technical data from the instruction manual must be respected;

If the ues are of a square or rectangular section, the internal edges must be rounded with a radius of not less than 20 mm.

For the rectangular section, the maximum ratio between the sides must be ≤ 1.5.

A section which is too small causes a reduction in draught. A minimum height of 4 m is advisable.

The following materials are FORBIDDEN and compromise the good operation of the appliance: asbestos cement, galvanised steel, rough and

porous internal surfaces. Picture 1 shows some example solutions.



For a correct installation please respect the sections/lengths of the ue shown in the technical data table. By installations

with dierent dimensions the ue must be suitably sized in accordance with EN13384-1.

The draught created by your ue must be sucient but not excessive.

A section of the ue which is too large can present a volume which is too large to heat and therefore cause operating diculties for the

appliance; to avoid this, it is necessary to intubate the appliance for its entire height. A section which is too small causes a reduction in draught.

ATTENTION: as far as concern the realisation of the ue connection and ammable materials please follow the requirements

provided by UNI 10683 standard. The ue must be at a suitably distance from ammable or combustible material using

suitable insulation or an air space.

It is FORBIDDEN to pass system piping or air ducts inside the ue. It is also forbidden to create moveable or xed openings on

the ue itself, for the connection of further dierent appliances (See chapter CONNECTING A FIREPLACE OR OPEN HEARTH TO THE

FLUE).

CHIMNEY POT

The ue draught depends on the suitability of the chimney pot.

It is therefore essential that, if built in a handcrafted way, the exit section is more than twice the internal section of the flue (Picture 2) .

As it must always go past the ridge of the roof, the chimney pot must ensure exhaust even in the presence of wind (Picture 3).

The chimney pot must meet the following requirements:

• Have an internal section equivalent to that of the chimney.

• Have a useful exit section of double the internal section of the ue.

• Be built so as to prevent rain, snow or any foreign body entering the ue.

• Be easy to inspect, for any maintenance and cleaning operations.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

La Nordica Gaia Forno Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info