626738

La Crosse WS-1516-IT Handleiding

16
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
61
--Indoor Temperature Readings
– Outdoor Temperature/Humidity Readings
--Wind Readings
--Rain reading
– Minimum and Maximum Readings
--Alarms
--History
– Forecast Icons
-Display information
– Power Source
FIRST THINGS FIRST, OR BATTERIES, BATTERIES, BATTERIES
Batteries are the number one warranty issue that we have. We recommend new, plain alkaline
batteries for our products.
A good alkaline battery will have an expiration date printed on it. Alkaline batteries are dated six
to seven years beyond the current year. Therefore a battery with an expiration date three years
beyond the current year has already been sitting on a shelf for three to four years. Consider what
happens to your car battery if you let it sit unused for three to four years.
If you have a voltmeter and your older batteries test to 1.48 or better, they should power our
products. New plain alkaline batteries often test to 1.6 or better.
Use good quality alkaline batteries with an expiration date of at least six years into the future or
newer. If you are using questionable batteries, be sure they measure at least 1.48 on a
voltmeter. Generic or store brand batteries, and batteries labeled super, ultra, max, heavy duty,
lithium and rechargeable should be avoided. These batteries provide their power at different
rates than plain alkaline batteries. This may cause problems, especially with the display unit. It is
not always a low battery that causes problems. It may be an overpowered battery.
– Proper Restart (Quick Set-up Guide)
62
In the event of installing or changing batteries in any of the units, all units need to be reset by
following the setup procedures.
1. Remove batteries from the Thermo-hygro (outdoor) sensor, Rain sensor and the
Base station (s).
Let sit without batteries for 15 minutes.
2.Then disconnect and reconnect the Wind sensor cable (be sure it clicks into place).
Reinsert the batteries into the Thermo-hygro sensor and Rain sensor first. Be sure to
use a new, quality alkaline battery (heavy duty and rechargeable types should be
avoided)
Note: It is important that the sensors be at least 5 feet from your base during the
restart.
3. Return to the base station, with the batteries out, and press any button 20 times.
Verify that the display is completely blank before proceeding.
4. Reinstall batteries in the display and do not press any other buttons for AT LEAST
30 minutes while the station completes its startup sequence.
5. Please note you may see Wind and Temperature/humidity, but you will generally
not see Rain until you tip the rocker 30 minutes after start up. This is
because the station will first find the Thermhygro sensor and spend 15 minutes
locking in this code. Then is will actively search for the Rain gauge for 15
minutes to lock in its code.
63
Mounting Sensors
It is best to set everything up in the house to be sure it works before mounting the sensors. Tip
the Rain gauge and spin the Wind sensor, to be sure they read to the base.
We do not have a complete sensor installation guide as each Home Installation is different and
covering all of the variables would result in a guide far longer than anyone would be willing to
read. Our website http://www.lacrossetechnology.com/support/setup.php
has some tips.
With that said, here are a few general guidelines to remember when installing your sensors:
Place the Wind sensor as high as you can install it. In most cases 4-6 ft above the peak of your
roof (or more) is required for accurate readings. (Avoid tall trees or other obstructions that may
block or reflect the wind).
Be sure to observe the Directions listed on the sensor. The point of the vane will tell you where
the wind is coming from.
Please carefully thread the Wind cord through the mast and be sure the cord fits in the slot or
hole designed to prevent pinching. Please note the proper Direction when mounting.
Be sure not to overtighten U bolts to mast, as they can crack the mast.
Avoid: Transmitting antennas. PVC pipe (unless electrical grade) as a mast, improper extension
cords (phone cord is much more resistant than our sensor cord) and modifications of the cords in
any way.
Please note most recording stations have sensors mounted 33 ft up or higher.
5. Install the Rain gauge on a level platform that is stationary. If the gauge isn't level it will
read low, and it it isn't stationary wind will cause it to read rain that isn't falling.
Tip: Be sure not to screw the rain sensor down too tightly as that will result in a low or
inaccurate reading.
64
6. Place the Rain gauge 2-3ft (or more) above the ground. This will prevent dirt from clogging
the gauge and will place it higher than most insects are willing to climb. Placing the gauge
extremely high is generally not a good idea as you may need to periodically clear debris
such as leaves, spider nests etc.
7. Place the Thermo-hygro sensor in a well-shaded area that is protected from direct rainfall
and sun, as it will read high if exposed to the sun. If the sensor gets too wet it will never
read accurate humidity again, so take care to ensure that it will not be exposed to a
downpour. Light incidental exposure to water typically will not harm the sensor.
8- A good location is under the eaves on the north side of the house. You can also build a
small roof or box for it if you do not have an overhang. Please be sure it is well vented.
9- Your Wind cord, must be plugged into the Thermo-hygro sensor before installing batteries.
Be sure the cord is secured from blowing around (do not staple or pinch), and occasionally
check for animals chewing through.
–Program Set Up Menu
There are five function keys: SET, +, HISTORY, ALARM, and MIN/MAX. You begin by pressing
the SET button until the display flashes. When you press and release the SET button after each
step, you will be moved to the next step. You may exit the programming mode at any time by
pressing the ALARM button.
If you stay at the set mode for more than 30 seconds, the unit will return to normal display mode.
If you want to change the settings, you just need to press the function keys you need. At this
stage, the unit will not return to the normal display mode. After changing the settings, you can
press and release the SET button to get to the next step.
1. CONTRAST SETTING:
Press and hold the SET button for two seconds. LCD and a number from 1-8 will be flashing. To
increase the contrast of the LCD display, press and release the PLUS button. To decrease the
… 16 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw La Crosse WS-1516-IT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van La Crosse WS-1516-IT in de taal/talen: Engels als bijlage per email.

De handleiding is 0,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info